Answered: )Find the cutting speed in meter/minute…

)Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle speed of 210 rpm. Cutting speed in meter/minute=

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter6: Milling

Section6.4: Indexing And Rotary Table Operations

Problem 6RQ: If the outside of a 6"-diameter disk is to be milled using a rotary table and a 3/4" diameter...

See similar textbooks

Related questions

Q: 11. Two cutting tools with tool life equations given below are being compared: Tool 1: VTº-1-150…

Q: In orthogonal cutting, the depth of cut is 0.5 mm at a cutting speed of 2 m/s. If the chip thickness…

Q: 1.To mill material having a cutting speed of 40 fpm. What should be the RPM of 1.25 inches diameter…

A: Velocity, V= πDN12, where, V= Velocity in fpmD= Diameter in inches (12 is divided in the above…

Q: . In an orthogonal cutting operationn, uncut chip thickness t is = 0.127 mm chip thickness t is =…

Q: 45) Find the RPM for turning a 1 1/4 inch shaft on a lathe with the material having a cutting speed…

Q: what is the cutting speed of a shaper having 80 strokes per minute with a length of a stroke at 1.25…

A: Given data, S = 80 stroke/min L = 1.25 feet = 15 in Find Cutting speed = V

Q: (b):- Calculate the total time to mill a block of aluminum with dimensions of 100 x 40 x 50 to…

Q: In a turning operation on stainless steel, cutting speed = 150 m/min, feed = 0.25 mm/rev, and depth…

A: From the given table write the specific energy for cutting stainless steel.

Q: Determine the optimum cutting speed for an operation on a lathe machine using the following…

Q: 1. A workpiece with 25mm diameter is turned in a centre lathe with a back rake angle of 12 degrees…

A: For solution refer below images.

Q: 9. Ceramics are the hardest tool materials in the world. 10. The smaller the cutting ratio, the…

A: Given: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Find the end mill diameter for slotting operation by a cutting speed of 16 meter /minute and spindle…

A: Given details: Cutting speedVc=16meter/minSpindle speedn=275rpmformula used : Vc=πdn1000

Q: Figure and table given below shows the design details of a taper turning operation with a cutting…

A: Given: cutting speed is 22 m/ minute. feed is 0.2 mm/ revolution. Depth of cut is 0.5 mm.

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

Q: If a fairing operation is executed at a rotational speed of 40.0 rev / min, the feed is 0.015 in /…

A: As the outer and inner diameter is not given so I am assuming it as D0 and Direspectivelya)…

Q: D d a° L1 SI. Parameter in Dimension in No: Drawing mm 1 d 35 2 L1 28 Cutting speed (Cs) in m/…

Q: In the following milling method, metal is cut by a cutter rotating in the same feed direction of…

A: Ans- b. Down milling.

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given D = 22 mm = 0.022 m Speed, N = 260 rpm

Q: A cylindrical mild steel work piece of Ø55 X 200mm undergoes a turning operation on a lathe machine…

A: Given data Diameter of work piece = 55 mmLength of work piece = 200 mmFinal diameter = 45 mmCutting…

Q: Determine the number of strokes per minute at which the shaper should run to machine a piece of…

A: The number of strokes per minute at which the shaper should run to machine a piece of copper is 96…

Q: The feed f in milling is usually given as a feed per cutter tooth; called the chip, it represents…

A: This statement is (TRUE)

Q: In orthogonal cutting if the depth of cut is a 1.25 mm and chip thickness after cutting is 2 mm,…

A: The cutting operation in which the angle between the cutting edge of tool and cutting velocity is 90…

Q: In a turning operation on cast iron (150 BHN), the cutting speed is 340 ft/min, feed is 0.06 in/rev,…

A: Given data as per question Cutting speed = 340 ft/min Feed =0.06 in/rev Depth of cut =0.05…

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

A: Given data Mill diameter (d) = 14 mm = 14 x 10-3 m Cutting speed (v) = 16 m/min

Q: The workpiece of size o 50 mm x 90 mm length is to be reduced to o 42 mm x 85 mm. If the depth of…

A: We have provided data from the question, Initial diameter= 50 mm; Initial length= 90 mm Final…

Q: 3. Using a lathe machine having a motor power of 4 KW and mechanical efficiency of 0.85, calculate…

A: Given: The power of the motor is, P=4 kW. The mechanical efficiency of the motor is, η=0.85. The…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following.…

A: In machining, taper turning is a process in which the diameter of cylindrical workpieces reduces…

Q: The blade on a typical table saw rotates at 3100 revolutions per minute. Calculate the linear…

A: Calculated the linear velocity in miles per hour of one teeth at the edge of the 10 inch diameter…

Q: QUESTION 1 Calculate the spindie speed in RPM of a lathe turning a 96 milimeter diameter material…

Q: A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an…

A: there are 4 subparts posted in 1 question, as per honor code and answering guidelines I can answer…

Q: Find the end mill diameter for slotting operation by a cutting speed of 18 meter /minute and spindle…

Q: Q) An engine lathe is used to turn a cylindrical work part 150 mm in diameter by 500 mm long.…

A: GIVEN: D=150mm L=500mm F=0.3mm/rev d=3mm Cutting speed, V=2.5m/s=2500X60=150000mm/min a) CUTTTING…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following. )…

A: The most common lathe machining operation is turning. A cutting tool removes material from the…

Q: Which option about chief elements in metal cutting is wrong? a)Chip width is the distance between…

A: Feed of cutting is expressed in mm per revolution. And cutting speed is expressed in mm per second.

Q: Find the end mill diameter for slotting operation by a cutting speed of 16 meter /minute and spindle…

Q: (j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min,…

A: Given data : stainless steel with hardness = 200 HB cutting speed (v) = 250 m/min feed (f) = 0.3…

Q: Question 3. A cemented carbide tool is used to turn a part with length= 18.0 in and diameter = 3.0…

Q: 8. Turning is a machining process in which a single-point tool removes material from the surface of…

A: The general process of turning involves rotating a part while a single-point cutting tool is moved…

Q: Question: Determine the optimum cutting speed for an operation on a Lathe machine using the…

A: Given:-Tc=tool change time=3 minTr=tool regrinds time= 3 minCm= Machine running cost= Rs 0.50 per…

Q: The blade on a typical table saw rotates at 3850 revolutions per minute. Calculate the linear…

Q: b):- Calculate the total time to mill a block of aluminum with dimensions of 100 x 40 x 50 to remove…

Q: In a machining operation, doubling the cutting speed reduces the tool life to 1/8th of the original…

A: Given:Taylor's tool life equation,VTn=C

Q: Table 1 below shows the cutting speed for some common materials and the feed rates for various…

Q: Q1_Tuming operation carried out on Aluminum shaft with specific energy of 0.7 N.m/mm. Cutting speed…

A: As per our guidelines we are supposed to do only first question, if more than one question asked,…

Q: In the horizontal milling machine, plain milling is accomplished on the top surface of a rectangular…

Q: 6. Compute for the necessary stroke per minute on 8 inches copper if it has 100 fpm as its cutting…

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

20)Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle speed of 210 rpm. Cutting speed in meter/minute=

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Figure and table given below shows the design details of a taper turning operation with a cutting speed of 22 m/ minute, feed 0.2 mm/ revolution; Depth of cut of 0.5 mm. Using the given data find the following. (a) Diameter "D" in mm . (b) Spindle speed in rpm. (c) Time for n passes to complete taper turning in minutes.
Figure and table given below shows the design details of a taper turning operation with a cutting speed of 22 m/ minute, feed 0.2 mm/ revolution; Depth of cut of 0.5 mm. (c) Time for n passes to complete taper turning in minutes .
Find the end mill diameter for slotting operation by a cutting speed of 16 meter /minute and spindle speed of 275 rpm. End mill diameter in mm =
6) Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a cutting speed of 16 meter /minute. Spindle speed in rpm=
Figure and table given below shows the design details of a taper turning operation with a cutting speed of 22 m/ minute, feed 0.2 mm/ revolution; Depth of cut of 0.5 mm. Using the given data find the following. (d) Time for single pass "Tsingle" in minutes
If a fairing operation is executed at a rotational speed of 40.0 rev / min, the feed is 0.015 in / rev and the depth of cut is 0.180 in, it determines: a) cutting time to complete the fairing operation; and b) the cutting speed; and c) The speed of metal removal at the beginning and end of the cut d) The power dissipated.
The following data is applicable for a turning operation. The length of job is 900 mm, diameter of job is 200 mm, feed rate is 0.25 mm/rev and optimum cutting speed is 300 m/min. The machining time (in min) is ___. A. 7.539 B. 7.90 C. 8.25 D. 9.00
Figure and table given below shows the design details of a taper turning operation with a cutting speed of 22 m/ minute, feed 0.2 mm/ revolution; Depth of cut of 0.5 mm. Using the given data find the following. (a) Diameter "D" in mm
It is required to cut screw threads of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If the spindle speed is 60 rpm, then the speed of the lead screw will be.
For the operation of straight turning in a lathe machine, the diameter of the workpiece is 80 mm, the length is 0.12 m, the cutting speed is 80 m / min, the feed is 0.5 mm / rev and the depth of cut is 0.002 m . Find the material removing rate and the time of machining.
Figure and table given below shows the design details of a taper turning operation with a cutting speed of 22 m/ minute, feed 0.2 mm/ revolution; Depth of cut of 0.5 mm. Using the given data find the following. (b) Spindle speed in rpm
1.) On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The cutting speed is _________?(m/min)