Find the throat diameter of a Venturi meter when fitted to a horizontal pipe 10 cm diameter having a discharge of 20lit/s. The differential U-tube mercury manometer, shows a deflection giving a reading of 60 cm, Ca 0.98. In case, this Venturi meter is introduced in a vertical pipe, with the water flowing upwards, find the difference in the reading of mercury gauge. The dimensions of pipe and Venturi meter remain unaltered, as well as the discharge through the pipe.

Find the throat diameter of a Venturi meter when fitted to a horizontal pipe 10 cm diameter having a discharge of 20lit/s. The differential U-tube mercury manometer, shows a deflection giving a reading of 60 cm, Ca 0.98. In case, this Venturi meter is introduced in a vertical pipe, with the water flowing upwards, find the difference in the reading of mercury gauge. The dimensions of pipe and Venturi meter remain unaltered, as well as the discharge through the pipe.

Name: P.7.5Find the throat diameter of a Venturi meter when fitted to a hor
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: P.7.5Find the throat diameter of a Venturi meter when fitted to a horizontal pipe 10 cmdiameter having a discharge of 20lit/s. The differential U-tube mercury manometer,shows a deflection giving a reading of 60 cm, Ca = 0.98. In case, this Venturi m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

No wrong answer ..When 0.23 m³/s of water flows through a 300-mm diameter pipe, the level difference in a U-tube manometer, connected between two points, separated by 120 m, is 280 mm of mercury. What is the friction factor for the pipe?
Water at 20°C flows through the orifice in Fig. ,which is monitored by a mercury manometer. If d = 3 cm,(a) what is h when the flow rate is 20 m3/h and (b) what isQ in m3/h when h = 58 cm?
The reservoirs in Fig. contains water at 208C. If thepipe is smooth with L = 4500 m and d = 4 cm, what willthe flow rate in m3/h be for Dz =100 m?
When 0.23 m³/s of water flows through a 300-mm diameter pipe, the level difference in a U-tube manometer, connected between two points, separated by 120 m, is 280 mm of mercury. What is the friction factor for the pipe?
Two reservoirs, which differ in surface elevation by 40 m,are connected by a new commercial steel pipe of diameter8 cm. If the desired flow rate is 200 N/s of water at 20°C,what is the proper length of the pipe?
If the pressure in a tank of oil (sp gr 0.85) is 376 kN/m2, what is the equivalent head (a) inmeters of oil; (b) in meters of water; (c) in meters of mercury? maintaining the liquid head h at 5.67 ft, to what pressure PA be raised in order to double the discharge?
Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a point 95 m below the reservoir surface. The turbine delivers 0.950 MW. Calculate the required flow of water in m3/min if friction is neglected. If friction were included would a higher or lower flow rate be required? (Note: The equation you will solve in this problem has multiple roots. Find a solution less than 1.0 m3/s.) V=___m^3/min?
A test on 30-cm-diameter pipe with water showed a gage difference of 33 cm on mercury-water manometer connected to two piezometer rings 120 m apart. The flow was 0.23 m/s. What is the friction factor?
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
An orifice on vertical wall has a head of 1.13m of oil ( sp.gr.=0.89). It discharges 6192N of oil in 88 seconds . The trajectory measures yield x = 2.4m and y = 1.37m . Assuming the area of the opening is 25cm2, Calculate Coefficient of Contraction, Coefficient or Velocity
nlet and throat diameters of a horizontal venturimeter are 350 mm and 150mm respectively. The liquid flowing through the venturimeter is water. Pressure intensity at inlet is 13.734 N/cm2 , while pressure at throat is 68.66 kPa. Find the actual flow rate, assuming Cd is 0.78.
A digital flowmeter on point in a system at P = 12.20 psia and T = 85.50 ∘C reads a value of 13.68 SLM. What is the actual volumetric flow rate of this stream in liters/min?