For a 34.4 mm diameter smooth pipe, calculate the threshold velocity (m/s) and corresponding flow rate (L/s) at which the flow regime in the pipe changes from transitional to turbulent. Use v = 10-6 m2/s for water at 20°C and t = 3.1415. Give your answers to 3 significant figures. Vtrans26.2 = (m/s) Qtrans26.2 = (L/s)

For a 34.4 mm diameter smooth pipe, calculate the threshold velocity (m/s) and corresponding flow rate (L/s) at which the flow regime in the pipe changes from transitional to turbulent. Use v = 10-6 m2/s for water at 20°C and t = 3.1415. Give your answers to 3 significant figures. Vtrans26.2 = (m/s) Qtrans26.2 = (L/s)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

I6 a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter pipe. Show your calculations. b) If the fluid velocity measured at the pipe center is 0.3 m/s and yields a Reynolds number based on local velocity of 4000, what is the fluid cross-sectional average velocity in the pipe? c) At what value of Re is the discharge coefficient of an orifice meter approximately independent of geometry and flow rate?
EXAMPLE 9 : The velocity of oil ( S = 0.8 ) through the 5 cm diameter smooth pipe is 1.2 m/s . L = 12 m , 24 = 1m . 2 = 2 m , and the manometer deflection is 10 cm . Determine the flow direction , the friction coefficient f , whether the flow is laminar or turbulent , and the viscosity of the oil.
In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the center, as measured by pitot tube are 2.4 m/s and 2.0 m/s respectively. Assume the flow in the pipe to be turbulent find: 1-Dischrge through the pipe,2-Coefficient of friction, 3 Height of roughness projections.Please do not waste my question solve with correct answers only.
The rate of flow of water in a 150 mm diameter is measured with a venturi meter with a 50 mm diameter throat. When the pressure drop over the converging section is 121 mm of water, the flow rate is 2.91kg/s. What is the coefficient for the converging cone of the meter at this flow rate?A. 0.81B. 0.985C. 0.90D. 0.745
estimate the distance X required to obtain a volume flow rate of 7.1 x 10^-3 m^3/s.
Three pipes connected in series with lengths L1 = L2 = L3 = 150 m and diameters D1 =75 mm, D2 = 50 mm, D3 = 25 mm. The discharge at the 25mm pipe = 200 lps, kinematic viscosity = 1.12 x 10-6 m2/s and ε = 0.35 mm. Using Colebrook and Darcy-Weisbach Formula, determine the following:a. relative roughness of the 25mm pipeb. roughness coefficient of 75mm pipec. head loss of 50 mm pipe
Air flows through a duct at 2,700 cubic feet per minute (CFM). After several feet and a few vents, the air-flow decreases to 1,890 CFM. What is the percent drop that has occurred? (Simplify your answer completely.)
What is the Reynolds number for a straight and perfectly smooth pipe of length 500 m and diameter 0.2 m, transporting oil (density 900 kg/m3 and viscosity 0.5 Pa-s) at a flow rate of 100 kg/s from sea level to an elevated height 10 m above sea level? What is the viscous pressure drop along the pipe?
For the given pipeline system, determine the nominal diameter, D, of the pipe. Minor losses are negligible and γw=9810 N/m3. Pipe roughness = 0.000010 m, Pipe length=200 m, kinematic viscosity=10-6 m2/s, and average discharge Q=0.2 m3/s. Consider ZA=110 m, ZB=80m and PI=3.14
A pipeline has the following data at its two section A and B Item Section - A Section - B Diameter (cm) 30 45 Elevation (m) 10 16 Pressure (k Pa) 40 30 Kinetic energy correction factor, α 1.08 1.25Assume ahead loss equal to 20 times the velocity head of A and calculate the discharge of water through this pipeline when flowing from B to A.
The Reynolds number is one of the most important dimensionless numbers that have been established in transport phenomena. Define what is the Reynolds number, explain its significance, and determine its limiting values for different flow systems, particularly for flow in a cylindrical channel. How is the Reynolds number defined for a channel that is not cylindrical? What is the hydraulic diameter?
What is the Reynolds number for a flow of oil (s.g. = 0.8, ft= 0.00200 lb -s/ft2) in a 6.5-in-diameter pipe at a flowrate of 8 ft3/s. Is the flow laminar or turbulent? Provide the free-body diagram.