For a 99.0 wt% Fe- 1.0 wt% C steel at a temperature just below the eutectoid, answer Question 27 - 30. Incorrect Question 26 The compositions of Fe3C = wt% C 6.67 Incorrect Question 27 The composition of ferrite (a) = wt% C 0.08 Question 28 Incorrect The amount of cementite (in grams) that forms in 100 g of steel. 6.67 Question 29 Unanswered The microconstituents present and the amount of each microconstituent.

For a 99.0 wt% Fe- 1.0 wt% C steel at a temperature just below the eutectoid, answer Question 27 - 30. Incorrect Question 26 The compositions of Fe3C = wt% C 6.67 Incorrect Question 27 The composition of ferrite (a) = wt% C 0.08 Question 28 Incorrect The amount of cementite (in grams) that forms in 100 g of steel. 6.67 Question 29 Unanswered The microconstituents present and the amount of each microconstituent.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The triple point of hydrogen occurs at a temperature of13.8 K and a pressure of 0.069 atm.(a) What is the vapor pressure of solid hydrogen at 13.8 K?(b) Suppose a sample of solid hydrogen is held under an external pressure of 0.030 atm and heated from 5 to 300 K. What phase change(s), if any, will occur?
10.15) A magnesium-lead alloy of mass 5.5 ka consists of a solid a phase that has a compo- sition that is just slightly below the solubility limit at 200°C (390°F). (a) What mass of lead is in the alloy? (b) If the alloy is heated to 350°C (660°F). how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase?
Copper and copper alloys as specified by the Copper Development Association (CDA) and are designated as C00001 thru C99999 in the Unified Numbering System (UNS). True False An alloy steel designated as AISI 4130 WQT 700 means: chromium-molybdenum alloy steel containing .30% carbon in solution, that is through heat treated and water quenched. True False An AISI 4340 alloy steel contains .43 percent or 43 points of the element carbon in solution. True False Chemicals from which the commercially important plastic resins are derived are themselves derived from natural products that are quite plentiful; these raw materials include coal, water, limestone, sulfur, salt, and petroleum. True False There are two (2) types of polymerization; addition or linear and cross-linked or condensation. Addition polymers are thermoplastics and cross-linked polymers are thermosetting materials. True False
the behaviour of graphite materials under stress
The Fe – Au solid – liquid T – xB phase diagram can be viewed as the intersection of asolid – phase miscibility gap with a solid – liquid phase – transition loop having aminimum at xAu = 0.8. The miscibility gap intersects the phase transition loop at xAu =0.1 and at xAu = 0.3. Fe has a higher melting point than Au. Sketch the phase diagramand label all the areas.
A substance exists in two solid modifications alpha and beta and also as liquid and vapour at a pressure of 1 atm alpha melts at a lower temperature to form liquid. Also alpha is denser than the liquid but beta is less dense than the liquid assuming that no meta stable equilibria are observed sketch p-t phase diagram show the significance of each point,line and region also show all triple points.
In analysis of an aluminum-zinc alloy, the mass of gelatin capsule is 0.1192g, mass of alloy is 0.2634g, mass of empty Beaker is 168.2449, mass of Beaker + Water is 272.5682g, the temperature of water is 22 degrees Celsius, the vapor pressure of water from table 1 is 19.827 mm Hg, Calculate mass of alloy sample.
An alloy of Component A and Component B, which do not react but are miscible in all proportions in molten state, is used to manufacture “Fail Safe” devices for boiler. Narrate the effect of composition on equilibrium: Solid ↔ Liquid with the help of a phase diagram, if the melting point of A (900 ºC), B (350 ºC) and the lowest melting of all compositions is 280 ºC at 12.6% of A and 87.4% of B.
1.50% Pearlite, 50% Tempered Martensite 2.50% Bainite, 45% Martensite, 5% Austenite
Select All the correct statements from below. a. If the averaged distance between partial dislocations for material A observed under TEM is smaller than material B, the estimated stacking fault energy of material A is lower than material B. b. K_IC is a material property that doesn't change with testing conditions c. The main difference between high cycle fatigue and low cycle fatigue is the difference in the number of cycles to failure d. A negative R value in fatigue test indicate the minimum stress is compressive in nature
A piston, 9 cm in diameter, is used to increase the internal pressure in a cylinder from 0 to 50 MPa. The cylinder, which is made of peak-aged aluminum alloy (yield strength = 500 MPa, Kic = 35 MPaVm), has the following dimensions: length = 20 cm, inner diameter = 9 cm and outer diameter =1 1 cm. The piston-cylinder arrangement suffered a malfunction which caused the cylinder to burst. Post-failure analyses showed the presence of a defect in the form of an elliptical flaw 4.4 mm long at the inner wall, 1.5 mm deep and oriented normal to the hoop stress in the cylinder. Compute the magnitude of the pressure at which the cylinder burst.
When the Ni-Ti shape-memory alloy (SMA) alloy is heated, austenite transformation occurs at As=50 ºC and completes at Af=80 ºC. Assume there is no austenite structure at room temperature. Propose a constitutive model to estimate the volume fraction of austenite structure in the SMA actuator at 70ºC.