For a 99.65 wt% Fe-0.35 wt% C alloy at a temperature just up the eutectoid teamperature, determine the following: (a) The fractions of each phases. (b) The Cooling curve for the specific alloy. (C) Descript the phases for this alloy. y+ Fe;C a + Fe;C 6.70 0.35 0.76 Composition (wt % C) allurgy I Bassim Sh Bache Temperature

For a 99.65 wt% Fe-0.35 wt% C alloy at a temperature just up the eutectoid teamperature, determine the following: (a) The fractions of each phases. (b) The Cooling curve for the specific alloy. (C) Descript the phases for this alloy. y+ Fe;C a + Fe;C 6.70 0.35 0.76 Composition (wt % C) allurgy I Bassim Sh Bache Temperature

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter26: Welding Metallurgy

Section: Chapter Questions

Problem 12R: What is a eutectic composition?

See similar textbooks

Similar questions

Q.1.For hypoeutoctoid plain carbon steel(select %C content yourself), determine the phasesthat are present, the compositionsof these phases, and the percentages or fractionsof the phases.Make schematic sketches of the microstructurethat would be observed for conditions of very slow cooling at the following temperatures: a)Just above the austenite transformation temperature b)The austenite transformation temperature -10C c)The eutectoid transformation temperature +10C d)The eutectoid transformation temperature -10C
When alloys A, B, and C are gently cooled from 1000 o C in the following temperature ranges, sketch their microstructures. (equilibrium cooling). List every phase present in the microstructures. Comment on the constituent phases of the resulting alloy and its mechanical characteristics. Please keep it brief.
A 80%Sn-20%Pb alloy is melted fully at 300°C and then slowly cooled down to 182°C. Sketch the microstructures at 300°C, 200°C, and 182°C, respectively. Label all phases and indicate their approximate compositions. Also, determine the follows for this alloy at 182°C. (1) The weight fractions of α and β phases.(2) The weight fractions of primary β and eutectic structure.(3) The weight fraction of eutectic β .
Copper-Nickel alloy is widely applied in industry. (a) List at least three applications where Cu-Ni alloy is used; (b) How many components and phases are shown in the below phase diagram? (c) For a mixture of 40 wt% Cu and 60 wt% Ni at 1320 oC, what phases are present? Identify theamount of these phases by applying “lever rule”.
For a steel with a 0.2 wt%C, what is the mass fraction and composition of phases at 600 (Please draw connections on the graph)
Describe the phases present at the eutectic temperature when the overall composition is x(Cu)= 0.5
Question: For 5.7 kg of a magnesium–lead alloy of composition 50 wt% Pb–50 wt% Mg, is it possible, at equilibrium, to have α and Mg2Pb phases with respective masses of 5.13 and 0.57 kg? If so, what will be the approximate temperature of the alloy? If such an alloy is not possible, then explain why.
Below is shown the isothermal transformation diagram for a 0.45 wt% C iron-carbon alloy. List the microconstituent(s) present for the heat treatment labeled (a)-(c) on this diagram. It is not necessary to state the proportion(s) of the microconstituents. I would love an explaiation aswel on how i whould read this diagram. Thanks
From the phase diagram of the Fe-0.25wt%C alloy below, determine the phase fraction and elemental composition of the resulting phase immediately after solidification across the eutectoid line (725 C). a.alpha_eutectoid = 96.6 wt% and cementite = 29.85 wt% b.alpha_eutectoid = 96.6 wt% and cementite = 3.4 wt% c.alpha_eutectoid = 1.05 wt% and cementite = 29.85 wt% d.alpha_eutectoid = 29.85 wt% and cementite = 1.05 wt%
Cite the phases that are present and the phase compositions for the following alloys: 15 wt% Sn–85 wt% Pb at 100°C
The solubility of tin in lead matches that required for precipitation hardening. Yet tin does not age-harden lead satisfactorily. Suggest a reason why it does not.
Using the TTT diagram for eutectoid steel, draw the specified cooling path on the diagram. Indicate what phases you expect in the final product with percentage of each phase. Assume the material has been fully austenitized before cooling. a. Water cool to room temperature b. Hot quench in molten salt to 690°C and then cooled isothermally for 2 hours: c. Hot quench to 610°C hold 3 minutes and water quench