For a data set of chest sizes (distance around chest in inches) and weights (pounds) of ten anesthetized bears that were measured, the linear correlation coefficient is requals 0.653. Use the table available below to find the critical values of r. Based on a comparison of the linear correlation coefficient r and the critical values, what do you conclude about a linear correlation? what is the critical values (Type integers or decimals. Do not round. Use a comma to separate answers as needed.)

For a data set of chest sizes (distance around chest in inches) and weights (pounds) of ten anesthetized bears that were measured, the linear correlation coefficient is requals 0.653. Use the table available below to find the critical values of r. Based on a comparison of the linear correlation coefficient r and the critical values, what do you conclude about a linear correlation? what is the critical values (Type integers or decimals. Do not round. Use a comma to separate answers as needed.)

Algebra & Trigonometry with Analytic Geometry

13th Edition

ISBN:9781133382119

Author:Swokowski

Publisher:Swokowski

Chapter5: Inverse, Exponential, And Logarithmic Functions

Section: Chapter Questions

Problem 12DE

See similar textbooks

Similar questions

The thickness of a conductive coating in micrometers has a density function of 600x−2 for 100 μm < x < 120 μm. a) Find the cumulative distribution function Choose an option:
A type of casting iron has Hall-Petch parameters: σ0 = 36.3 MPa and K = 6.5 MPa ∙ mm^−0.5. For a given sample, the grain size distribution is shown in the diagram below. Each bar represents the percentage of grains in particular size. First, estimate the average grain size based on concept of “weighted mean” (in case you do not know, search for this term). Then, apply Hall-Petch Equation to calculate the yield stress. (Note: 1 μm = 0.001 mm)
In the tank of 100 liters of brine containing 65kg totally dissolved salt. Pure water is allowed to run into the tank at the rate of 3 liters per minute. Brine runs out of the tank at rate of 2 liters minute. The instantaneous concentration in the tank is kept uniform by stirring. How much salt is in the tank at the end of 1 hour?
Sulfur dioxide (SO2) pollution is a known cause for corrosion of exposed steel. To document this effect in actual conditions, steel weight loss (gm/m3/yr) was measured at 36 locations in a large city, along with the rate at which SO2 was deposited (mg/m2/day). Perform a two-sided test of H0: ρ = 0.800, with α = 0.01. SO2 Loss 22.6 580 26.1 563 19.1 339 17.2 346 25 623 16.8 420 42.7 951 30.4 794 17.9 461 30.4 757 27.8 573 27.8 656 33 990 14.2 551 37.4 856 16.2 443 27.7 802 22.7 657 21 495 15.8 496 13.7 353 24.7 724 23.7 602 30.7 639 33.5 813 30.2 770 20.1 556 22.8 557 39.9 1001 15.5 432 40.4 940 27.9 687 39.4 919 25.1 590 28.6 640 29.7 702
A tank contains 200 L of fluid in which 30 grams of salt is dissolved. Brine containing 1 gram of salt per liter is then pumped into the tanks at a rate of 4 L/min; the well mixed solution is pumped out at the same rate. Find the A(t) or amount of salt in the tank at any time t.
The bottom of a cylindrical container has an area of 10 cm². The container is filled to a height whose mean is 5cm, and whose standard deviation is 0.1 cm. Let V denote the volume of fluid in the container. a) Find μV. b) Find σV.
The bottom of a cylindrical container has an area of 10 cm2. The container is filled to a height whose mean is 6.00 cm, and whose standard deviation is 0.300 cm. Let V denote the volume of fluid in the container. 1) Find μV . 2) Find σV .
The life of an automotive component can be modelled by Weibull distribution α =6.2?105 and β =1.3. (a) Calculate the cumulative density function, F (t) (b) Calculate the reliability function, R (t) and the hazard function, h (t) at the end of the rotating period of 36000 miles.
Find the average value of ƒ(x) = e2x on [0, ln 2].
A tank contains 400 gal of Brine in which 40 lbs of salt is dissolved. Brine containing 0.25 lb/gal runs into the tank at the rate of 2 gal/min. The mixture is kept uniform by stirring, runs out of the tank at the rate of 1gal/min. Assuming the tank is to be sufficiently large to avoid overflow. a) What is the amount of salt after 6 minutes?b)When will the amount of salt in the tank to be 50 lbs?
heat boundry value PDE
the joint distribution of Y and X is given by: 4/3 · ln y, and the follow boundary: 0<x<y<1 Determine the distribution of U = −log(Y/X)