For an average temperature of 21°C, water flows through a 15 cm diameter pipe that is 2.5m long. The pipe wall is heated by steam and is held at 100°C. The convective heat transfer coefficient is 2.25 x 10* W/m?.K. Determine the following: a) The heat flow in W b) Explain the concepts/principles that were considered and the factors that affected the condition of the above mentioned items (a & b).

For an average temperature of 21°C, water flows through a 15 cm diameter pipe that is 2.5m long. The pipe wall is heated by steam and is held at 100°C. The convective heat transfer coefficient is 2.25 x 10* W/m?.K. Determine the following: a) The heat flow in W b) Explain the concepts/principles that were considered and the factors that affected the condition of the above mentioned items (a & b).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.27P

See similar textbooks

Similar questions

Water at a temperature of 77C is to be evaporated slowly in a vessel. The water is in a low-pressure container surrounded by steam as shown in the sketch below. The steam is condensing at 107C. The overall heat transfer coefficient between the water and the steam is 1100W/m2K. Calculate the surface area of the container that is required to evaporate water at a rate of 0.01 kg/s. Problem 1.16
Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
A mild-steel cylindrical billet 25 cm in diameter is to be raised to a minimum temperature of 760C by passing it through a 6-m long strip-type furnace. If the furnace gases are at 1538C and the overall heat transfer coefficient on the outside of the billet is 68W/m2K, determine the maximum speed at which a continuous billet entering at 204C can travel through the furnace.
Determine the mean heat-transfer coefficient and the quantity of heat transferred in water flowing in a horizontal tube 3 mm in diameter (d) and 2 m long (l), if ω = 0.3 m/sec; tf = 60 deg C and tω = 20 deg C. Constants: @ tf = 60oC, λf = 0.567 kcal/m-hr-oC; νf = 0.478 x 10-6 m2/sec β = 5.11 x 10-4 1/oC and Prf = 2.98. @ tω = 20oC, Pr? = 7.02
Local Nusselt number is given as Nux=0.04Rex0.9 Pr 1/3. Obtain an expression for, a) average heat transfer coefficient, h1 x b) local heat transfer coefficient, hx c) What is the ratio of the average to local coefficient, h1x / hx
A thick concrete wall having a uniform temperature of 50oC is suddenly subjected to a stream of water so that the surface temperature is suddenly lowered to 15oC. How long will it take to cool the concrete to 30oC at a depth of 5 cm from the surface? Data: concrete properties, k = 1.37 W/m×oC, r = 2100 kg/m3, a = 7.5×10-7 m2/s.
Most automobiles have a coolant reservoir to catch radiator fluid that may overflow when the engine is hot. Such a radiator, made of copper, is filled to its 12-L capacity when at 10.0°C. -What volume of radiator fluid, in liters, will overflow when the radiator and fluid reach their 99.5°C operating temperature, given that the fluid’s thermal coefficient of volume expansion is 400.0 × 10-6 / °C? The coefficient of volume expansion for copper is 5.1 × 10-5 /°C.
Heat Transfer Course Copper balls with an initial temperature of 200 degrees centigrade(ρ = 8933 kg / m3, k = 401 W / m oC, cp = 385 J / kg oC, α = 1.166 * 10-4 m2 / s) in air at 30 degrees centigrade 2 it is allowed to cool down for a period of minutes. Since the balls are 2 cm in diameter and the heat transfer coefficient is 80 W / m2 oC,a) What is the temperature of the balls at the end of the cooling process?b) If 1000 balls per hour are left to be cooled, what is the total heat transfer from the balls to the air?
4.) A 15-cm-diameter steam line carries saturated steam at 6 MPa and is located in a tunnel with stagnant air with a temperature of 50oC. The outside unit convective coefficient is 8.5 W/m2-K. The steam line is covered with 3 cm of 85% magnesia insulation. It is decided to reduce the heat loss by one-half. How much 85% magnesia insulation is required? Neglect thermal resistance of pipe and inside surface.
Compute the rate of convective heat transfer, in kW, from an uninsulated steam pipe, that has an outer surface temperature of 200oC in an ambient condition where the air temperature is 20oC. The heat transfer coefficient is known to be 10 W/m2-oC. The outer diameter of the pipe is 0.15 meters and is 30 meters long...
As part of an industrial pipe system a 6-meter-long by .5 meter inner diameter copper pipeweighing 200kg holds a lubricating oil in place while is heats from 20 deg C to 55 deg C. At thatpoint, the valve opens and allows to oil to flow through. What is the total heat transferrequired? And, what percentage of the heat transferred does the oil and copper each accountfor? (oil density = .9 kg/L , oil specific heat = 1800 J/kgC)
Heat transfer Calculate the heat transfer rate in Btu/hr through the pipe ona stainless steel pipe with a length of 12m has an inner diameterof 10in and an outer diameter of 13in. The temperature of theinner surface of the pipe is 50°C and the temperature of theouter surface is 48°C. The thermal conductivity of the stainlesssteel is 187 W/m-°C. Show complete solution in a clear paper.