Q:A hot surface at 100°C is to be cooled by attach- ing 3-cm-long, 0.25-cm-diameter aluminum pin fins (k 237 W/m · °C) to it, with a center-to-center distançe of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m2 · °C. %3D Determine the rate of heat transfer from the surface for a 1-m X 1-m section of the plate. Also determine the overall effectiveners of the fins. Ans. Q=17.4 kW , E fin = 7.1 3 cm 0.6 cm 0.25 cm

Q:A hot surface at 100°C is to be cooled by attach- ing 3-cm-long, 0.25-cm-diameter aluminum pin fins (k 237 W/m · °C) to it, with a center-to-center distançe of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m2 · °C. %3D Determine the rate of heat transfer from the surface for a 1-m X 1-m section of the plate. Also determine the overall effectiveners of the fins. Ans. Q=17.4 kW , E fin = 7.1 3 cm 0.6 cm 0.25 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The blades of a wind turbine turn a large shaft at a relatively slow speed. The rotational speed is increased by a gearbox that has an efficiency of 0.93. In turn, the gearbox output shaft drives an electric generator with an efficiency of 0.95. The cylindrical nacelle, which houses the gearbox, generator, and associated equipment, is of length L = 6 m and diameter D = 3 m. If the turbine produces P = 2.5 MW of electrical power, and the air and surroundings temperatures are T = 25 oC and Tsur = 20 oC, respectively, determine the minimum possible operating temperature inside the nacelle. The emissivity of the nacelle is 0.83, and the convective heat transfer coefficient is h = 35 W/m2 .K. The surface of the nacelle that is adjacent to the blade hub can be considered to be adiabatic, and solar irradiation may be neglected. Use Fin or N number of fins to reduce the Ts of the nacelle less than 143 oC
A cylindrical fuel rod (k = 30 W/m•K) of 2 cm in diameter is encased in a concentric tube and cooled by water. The fuel rod generates heat uniformly at a rate of 100 MW/m3, and the average temperature of the cooling water is 115°C with a convection heat transfer coefficient of 2500 W/m2.k. The operating pressure of the cooling water is such that the surface temperature of the fuel rod must be kept below 200°C to avoid the cooling water from reaching the critical heat flux (CHF). The critical heat flux is a thermal limit at which a boiling crisis can occur Determine the temperature at the surface of the rod. What can you do to lower the temperature aty the surface?
A 300-ft-long section of a steam pipe whose outer diameter is 4 in passes through an open space at 50°F. The average temperature of the outer surface of the pipe is measured to be 280°F, and the average heat transfer coefficient on that surface is determined to be 6 Btu/h·ft2·°F. Determine (a) the rate of heat loss from the steam pipe and (b) the annual cost of this energy loss if steam is generated in a natural gas furnace having an efficiency of 86 percent, and the price of natural gas is $1.10/therm (1 therm = 100,000 Btu).
Consider a steam pipe of length 15 ft, inner radius 2 in., outer radius 2.4 in., and thermal conductivity 7.2 Btu/hr-ft-°F. Steam is flowing through the pipe at an average temperature of 250°F, and the average convection heat transfer coefficient on the inner surface is given to be 1.25 Btu/hr-ft2-°F. If the average temperature on the outer surfaces of the pipe is 160°F, determine the rate of heat loss from the steam through the pipe. ANSWER:______Btu/hr
In a meat processing plant, 2-cm-thick steaks (k =0.45 W/m·K and a = 0.91 * 1027 m2/s) that are initially at25°C are to be cooled by passing them through a refrigerationroom at 211°C. The heat transfer coefficient on both sides ofthe steaks is 9 W/m2·K. If both surfaces of the steaks are to becooled to 2°C, determine how long the steaks should be keptin the refrigeration room. Solve this problem using analyticalone-term approximation method (not the Heisler charts).
Steam at To1= 320°C flows through a cast iron pipe (k = 80 W/mK) with inner and outer diameters of D1= 5cm and D2 = 5.5 cm, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/mk(Figure Q2). Heat is lost to the surroundings (To2 = 5°C) by natural convection and radiation, with a combinedheat transfer coefficient of h2 = 18 W/m2.K.(a) Taking the heat transfer coefficient inside the pipe to be h1 = 60 W/m2 K, Calculate the rate of heat lossfrom steam per unit length of pipe.(b) Calculate the temperature differences between the pipe shell and the insulation. Someone comments that a microwave oven can be viewed as a conventional oven with zero convectionresistance at the surface of the food. Is this a correct statement? Discuss the reason.
10 m long pipe is being used to deliver steam through a processing plant. The inner radius of the pipe is r1 = 6 cm and the thickness of the pipe is 2 cm. Thermal conductivity k = 8 W/m⋅K and the average temperature steam flowing through the pipe is 160°C, the average convection heat transfer coefficient on the inner surface is given to be h = 20 W/m2⋅K. If the average temperature on the outer surfaces of the pipe is T2 = 70°C, (a) express the differential equation and the boundary conditions for steady operating conditions, (b) determine a relation for the variation of temperature in the pipe, and (c) evaluate the rate of heat loss (heat of conduction) from the steam through the pipe.
A spherical container with an inner radius r1 = 1 m and an outer radius r2 = 1.05 m has its inner surface subjected to a uniform heat flux of q1=7kw/m^2. The outer surface of the container has a temperature T2 = 25°C, and the container wall thermal conductivity is k = 1.5 W/m·K. Show that the variation of temperature in the container wall can be expressed as and determine the temperature of the inner surface of the container at r = r1.
A hollow spherical iron container with outer diameter 20 cm and thickness 0.2 cm is filled with iced water at 0°C. If the outer surface temperature is 5°C, determine the approximate rate of heat loss from the sphere, in kW, and the rate at which ice melts in the container. The heat of fusion of water is 333.7 kJ/kg.
A 10 hp fan is used in a room for circulation purposes. Assuming a sealed room. that is well insulated, determine the internal energy increase in Btu after 2 h of operation.
A person puts a few apples into the freezer at -13°C to cool them quickly for guests who are about to arrive. Initially, the apples are at a uniform temperature of 37°C, and the heat transfer coefficient on the surfaces is 6.3 W/m2 · °C. Treating the apples as 8.2-cm-diameter spheres and taking their properties to be ρ= 836 kg/m3, Cp = 4.05 kJ/kg · °C, k= 0.426 W/m · °C, and α= 1.43 ×10-7 m2/s, determine the center and surface temperatures of the apples in 1.9 h
Hot water is flowing at an average velocity of1.5 m/s through a cast iron pipe (k = 52 W/m·K) whose innerand outer diameters are 3 cm and 3.5 cm, respectively. Thepipe passes through a 15-m-long section of a basement whosetemperature is 15°C. If the temperature of the water dropsfrom 70°C to 67°C as it passes through the basement and theheat transfer coefficient on the inner surface of the pipe is400 W/m2·K, determine the combined convection and radiationheat transfer coefficient at the outer surface of thepipe.