You must design a dust plant. If the grizzly area for which the plant is designed for is 2 x 3 m in size, how many dry filter bags would you require to adequately filter the air and re-introduce it into the fresh air? Filter bag air velocity is 0.1 m/s and the grizzly area air velocity is 0.5 m/s.

You must design a dust plant. If the grizzly area for which the plant is designed for is 2 x 3 m in size, how many dry filter bags would you require to adequately filter the air and re-introduce it into the fresh air? Filter bag air velocity is 0.1 m/s and the grizzly area air velocity is 0.5 m/s.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.22P

See similar textbooks

Related questions

Q: Low thermal conductivity coatings on turbine blades protect the blades from hot gas by:

A: This question is based on the concept of coatings on turbine blade.

Q: If the specific weight of a liquid is 58.5 lbf per cubic foot, what is the specific volume of the…

A: unit of specific volume is ft3/ slug and not slug/ft3 . slug/ft3 is unit of density.

Q: Given the beam shown below, determine the shear force and bending moment at point C. Given the…

Q: 41. In a bolted joint two members are connected with an axial tightening force of 2200 N. If the…

A: Given that, We know two members are connected in bolted joint W=2200N, p=4 mm=0.004

Q: 1. Locate the centroidal x and y of the composite figures. Use the reference axes provided.

Q: Initially at rest, A Mitsubishi Pajero and a Toyota Vios are connected by a tow cable. The winch on…

A: Given: relative velocity = 5 m/s length = 5 m mass A = 2.5 Mg mass B = 1.25 Mg

Q: S Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the…

Q: Draw the front view and top view

A: I am using solid works to draw three projection views.

Q: Example 3 A 0.5 kg object travelling with a speed of 12m/s impacts a spring one side of a spring…

Q: An engine has a thermal efficiency of 40%. It is used to drive a refrigerator having a COP of 5.0.…

Q: The simple truss shown supports the two loads, each of magnitude L. Deter- mine the forces in…

A: When a push or the pull applied on the body having mass 'm', it has the tendeycy to change it's…

Q: Q1 Rotate the box in the figure, about line OA clockwise by 30°, then about line OB counterclockwise…

A: In this question the box is rotating about the line OA clockwise by 30o and after that it is…

Q: Completely solve and box the final answers. Write legibly. 2. A centrifugal water pump operating at…

Q: A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top…

Q: A golf ball is launched with the initial conditions shown in the figure. Determine the radius of…

Q: (a) Determine the radius of curvature of the trajectory and the time rate of change of the speed of…

Q: Pressure = 450.50 kPa at depth of 30-m; determine the unit weight in kN/m³ O 16.16 O 15.01 O 294.3 O…

Q: An open tank has a vertical partition and on one side contains gasoline with a density p = 700 kg/m³…

A: Given Density = 700 kg/m3 Depth = 4 m Area, A = 4 x 2 m2 Find Depth, h

Q: What is the speed of the connector pin at B if the angular velocity of the bar AB is 8 rad/s…

Q: Determine the maximum mass (kg) that can be lifted at E if the 10-HP motor A has a maximum rotation…

A: Given DataP=10hPN=300 rpmdab=10mmdce=15mmrb=100mmrt=150mmFOS=1.2

Q: A test car starts from rest on a horizontal circular track of 95-m radius and increases its speed at…

Q: Calculate the resultant (1) V₁ + V2 + V3 and (II) V₂ + V1-V3 when V₁ = 120 N at 140° V₂ = 80 N at…

A: Given v1 = 120 N at 140o v2 = 80 N at 120o v3 = 300 N at 220o Find Resultant

Q: Q2.A/ Show that the expression (1/2 mv² = √mgh) is dimensionally correct, where v is the velocity…

Q: 3. Figure Q3 shows a conical bearing subjected to a uniform pressure distribution at its surface of…

Q: Five kilogram of steam is initially at 1MPa and y=40% inside the piston cylinder. There is a 50C…

A: Given:m=5 kgP1=1 MPax=0.4

Q: A lubricated bolt needs an initial torque of 145 lb-ft to take the initial tension brought by the…

A: Given data Lubricated bolt needs an initial torque of 145 lb-ft. We have to determine the initial…

Q: velocity of 20 fps at 40o to the horizontal prior to striking the soccer player’s head. After the…

Q: A material is subjected to plane stress. Part A For the distortion-energy theory of failure, express…

A: Hajaj

Q: Draw the shear-force and bending-moment diagrams for the beam shown. Determine the bending moment…

Q: 3435 E1 (B) Air at 27°C flows over a flat plate with a velocity of 3 m/s. Calculate the boundary…

Q: A new fuel for combustion was found to have the following composition: carbon 71.6%, hydrogen 4.8%,…

Q: Find the kinetic energy Mass=0.8 kg Velocity=3.3 m/s

A: Given:m=0.8 kgv=3.3 m/s

Q: The motor unit A is used to elevate the 300-kg cylinder at a constant rate of 2 m/s. If the power…

Q: Q3) The three flat blocks are positioned on the 30° incline as shown, and a force P parallel to the…

A: Introduction: When an object is put on a slanted surface, it frequently slides down the surface. The…

Q: The state of strain at the point on the pin leaf has components of € = 200(10-6) Ey 180(106), and…

Q: The distributed load is supported by a box beam as shown below. Determine the maximum value of wo…

Q: What thermodynamic cycle in realised in the internal combustion engines?

Q: . A main shaft has 100mm diameter is running at 350rpm, what power could be delivered by the shafts?

Q: A certain gas at temperature equivalent to 24 degrees Celsius at 8 cu.m and 200 kPa is compressed to…

A: The resulting pressure is 457.14 kPa.

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

Q: (ii) Consider the process of baking potatoes in a conventional oven. Can the hot air in the oven be…

Q: A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top…

Q: Determine the depression of the meniscus when a tube 2 mm diameter containing mercury is immersed in…

Q: The soccer ball shown weighs 1 lb and has a velocity of 20 fps at 40° to the horizontal prior to…

Q: ) Initially at rest, A Mitsubishi Pajero and a Toyota Vios are connected by a tow cable. The winch…

A: Given: Mass (Pajero) = 2.5 Mg Mass (Toyota) = 1.25 Mg L = 5m Vrelative = 2 m/s

Q: Question 10 (1 point) Saved Listen What type of flow meter obtains flow measurement by the number of…

Q: Continuous level measurement in a tank filled with grain can be done using a _________ sensor.

Q: 8. A piston and cylinder arrangement contains saturated water vapor at 110 deg C. The vapor is…

A: Given:T1=110 °CP2=1.6 MPa

Q: A thread with specification of M-16x2-6g takes a tensile load of 100 lb. Determine its tensile…

A: Given Load, P = 100 lb = 45.35 kg Diameter, d = 16 mm Find Tensile stress

Q: Musical Instruments: A man wants to learn to play guitar. He finds a model he likes for $559. He…

A: When a string's end is fixed, the string's displacement at that end must be zero. A transverse wave…

Question

You must design a dust plant. If the grizzly area for which the plant is designed
for is 2 x 3 m in size, how many dry filter bags would you require to adequately
filter the air and re-introduce it into the fresh air? Filter bag air velocity is 0.1 m/s
and the grizzly area air velocity is 0.5 m/s.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pulse-jet baghouse is desired for a finished cement plant. Calculate the number of bags required to filter 500 m3/min of air with a dust loading of 3.0 g/m3. Each bag is 3.0 m long with a 0.13 m diameter. If the average pressure drop is 1.0 kPa and the main fan is 60% efficient, calculate the fan power in kW. If the pulse air volumetric flow rate is 0.5% of the filter airflow rate and the pulse air pressure is 6.0 atm, calculate the power drawn by a 50% efficient compressor (in kW)
Calculate the Cunningham correction factor for a particle with a 0.03-micron diameter in air at 1 atm pressure and 0 °C.
How is a lubricant drop be broken into finer droplets of a mist ?a. By increasing its kinetic energy by vibrating it at high frequencyb. By placing the drop into a zone of low pressure which is less than the internal pressure of the drop,generated by a venturi.c. By evaporating the drop into molecular form by reducing its pressure.d. By placing the drop into a highly turbulent zone such that a number of air jets blown onto it shearsit into fine droplets of a mist.
Consider a constant updraft in the central core of a warm cloud (T>0∘C) isolated from entrainment. Why does the average cloud droplet radius increase with height in this updraft core? a.The adiabatic liquid water content increases with height above cloud base. b.The average cloud droplet radius only increases if new CCN are activated. c.The cloud droplet growth rate depends on the inverse of the average cloud droplet radius.
A series of 10 chips are placed on an insulating substrate as shown in the figure. Each chip has a length (Lc) of 15 mm, it is 20 mm wide and 10 mm thick. Upstream of the chips there is an input length (Le) of 15 mm. Whether each chip should dissipate 0.5 W and stay at a maximum temperature of 80 °C, what should be the speed uꝏ that the ambient air at 25 °C should be blown so that this condition is met? The emissivity of the chips is 0.8. consider that the chips do not exchange heat with each other and there is a turbulence generator upstream of the plate.
Air at -10° C flows over a smooth sharp-edged, almost flat aerodynamics surface that is held at 10°C, at a speed of 120 km/hr . What is the greatest length the plate can be if the flow is to remain laminar over the entire length of the plate? What would be the average film coefficient be of that plate and what is the heat flux? What are the heights of the fluid and thermal boundary layers at the end of that length? Use Re = 350,000 for the critical Reynolds number.
Consider a flat plate placed inside a wind tunnel, and air at 1 ATM and 20°C is flowing with a free flow velocity of 60 m/s. What is the minimum length of the plate needed for the Reynolds number to reach 2 × 107? If the critical Reynolds number for external flow is 5 × 105, what type of flow regime would the airflow experience at 0.2 m from the leading edge? I need the solution from fundamental concepts of how the heat flow behaves in the system
How does an increase in gas temperature affect pressure drop in a haghouse, assuming the mass flow rate of particles and the molar flow rate of gas are constant?
Dry air at 25◦C and atmospheric pressure blows over a 30-cm-square surface of ice at a velocity of 1.5m/s. Estimate the amount of moisture evaporated per hour, assuming that the block of ice is perfectly insulated except for the surface exposed to the airstream.
a.) What would the air velocity ua in a cleanroom have to be to produce a characteristic length equivalent to the width of a 0.01m diameter line, taking the Reynolds number Re = 10 (typical for a cleanroom) or 2300 (upper bound for laminarity)? b.) Why is the velocity at the lower end of the range impractical? c.) Given typical cleanroom parameters for Re and ua, what is the characteristic length we actually have to work with?
There is a flow of air that circulates over a flat plate that is used to store a food product at a temperature of 95 ° C throughout its surface. The air flows at a speed of 2.5 m/s and has a temperature of 25.0°C. The plate measures 600.0 mm · 300.00 mm. As a task assigned by your plant operations manager, you are asked to answer the following questions: i. Determine the heat loss from the plate if the air flows parallel to the 600.00-mm side.ii. How would this heat loss be affected if the airflow is made parallel to the 300.0-mm side? For this type of configuration, the coefficient of heat transfer by forced convection, h, can be obtained from the relation IMAGE BELOW The previous correlation is valid for the laminar regime, that is: Re < 500000
Assume that hail stones are spheres (s=0.75) with a diameter of 10 mm. What is the terminal velocity in standard air? Ans: 14.29 m/s