Answered: For external forced convection with an…

For external forced convection with an isothermal surface, what is the Nu# correlation equation for laminar flow if you are looking for total heat transfer?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.24P

See similar textbooks

Related questions

Q: For a natural convection from the vertical plates, if Rayleigh number is given as 1 × 101º then the…

A: Given, Rayleight number = Ra = 1 x 1010 For 109 < Ra < 1012, nusselt number (Nu) can be…

Q: Water at 10°C is is flowing at 0.8 m/s across a long cylinder that is made of a material that…

Q: à heat transfer takes place by convection _with ficient of h = 60 W/m2 · °C. Calculate (a) the…

Q: Q : Engine oil at 80°C flows over a 10-m-long flat plate whose temperature is 30°C with a velocity…

Q: a) What is forced convection? How does it differ from natural convection? Is convection caused by…

Q: a) What regions show the largest oceanic latent heat loss? b) What regions show the saltiest…

A: given; a) What regions show the largest oceanic latent heat loss? b) What regions show the saltiest…

Q: Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with…

Q: For internal forced convection, friction factor f can be found by using either the Moody charts, the…

A: The Moody chart or Moody diagram (also Stanton diagram) is a graph in a non-dimensional form that…

Q: ngine oil enters the 5 mm diameter pipe at 120°C. and the Re number is about 1000. Calculate the…

Q: 3) Explain the difference between forced and free convection

Q: 60°C glycerin flows over a 15m long flat plate with temperature of 20°C. The velocity of glycerin is…

A: Prandtl number is the only dimensionless number that is the property of the fluid. It is defined as…

Q: Hot water is being transported in a horizontal pipe (k = 0.15 W/m∙K, Di = 2.5 cm, Do = 4.5 cm),…

A: Given data Thermal conductivity of the pipe = 0.15W/mK Inner dia of pipe Di = 2.5 cm = 0.025m ri=…

Q: Consider oil flowing along with a flat plate parallelly. The oil flow creates laminar velocity and…

Q: and Surface temperature 4. In what functions does Nusselt number in natural convection differ from…

Q: If forced convection uses Reynolds number to account for fluid movement during forced convection,…

A: Convection heat transfer: The heat transfer due to the motion of the fluid (air) is known as…

Q: QO What are the types of convection heat transfer?

A: Heat transfer takes place in three types 1. Conduction 2. Convection 3. Radiation

Q: 3n a manufacturing process, long aluminum rods of squaire cross section withd 21 mmare cooled from…

Q: 24. Water at 80 F is flowing over a flat plate with a velocity of 8 ft/s. The plate is 5 ft long.…

A: Given: temperature of the water→T=80°F velocity of the water→v=8 fts=2.43 msec Length of the…

Q: Define the cooling of a boiled egg by forced and natural convection.

A: Rate of heat transfer by convection is given by Where h is convective heat transfer coefficient.…

Q: A 25-cm circular grill has an emissivity of 0.9. The temperature of the air and surrounding surfaces…

A: To determine the heat transfer from the grill, first of all we need to determine the Reynold number…

Q: (1) Explain the concept of convection heat transfer. What are the methods used for calculating the…

A: To find :- Concept of convective heat transfer and methods used for calculating the heat transfer…

Q: 1.0 Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate…

A: Given data: Film temperature = T = 300 K velocity = u = 1 m/s Distance from leading edge = x = 20 mm…

Q: Volumetric thermal expansion is used in modeling natural convection heat transfer. Derive an…

Q: The heat transfer from a 2-m-diameter sphere to a 25 °C air stream over a time interval of one hour…

Q: -10-A circular, hot gas jet at T, is directed normal to a circular plate that has radius r, and is…

Q: Differentiate between free and forced convection with examples.

Q: A hot fluid (kfluid = 0.72 W/m∙K) is flowing as a laminar fully-developed flow inside a pipe with an…

Q: Air at 1 atm is flowing at a velocity of 1.5 m/s across a flat plate. The film temperature between…

Q: For fluids with small Prandt number the thermal boundary layer development is much choose your…

A: For fluids with small Prandtl number the thermal boundary layer development is much more rapid than…

Q: 6.18 Assuming a transition Reymolds number of 5 × 105, determine the distance from the leading edge…

A: Critical renoylds number is given asRec=ρu∞xcμxc=5×105μρu∞

Q: Consider a flat plate positioned inside a wind tunnel, and air at 1 atm and 20°C is flowing with a…

Q: Air (can be assumed as an ideal gas) at an ambient temperature of 30°C flows across (perpendicular…

Q: Consider a hot baked potato. Will the potato cool faster or slower when we blow the warm air com ing…

A: It will cool faster in case of warm air coming from lung.

Q: The convection heat transfer coefficient is usually higher v in natural convection than forced…

Q: A can of engine oil with a length of 150 mm and a diameter of 100 mm is placed vertically in the…

A: The data given is, Length of the can of engine oil, L = 150 mm = 0.150 m Diameter of the can of…

Q: Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with…

A: Given data: Film Temperature = Tf = 300 K Fluid velocity = u = 1 m/s Fluids are : Air, Water, Engine…

Q: iB swionnoed by A UOcmo8Ocm vertical plate 26°C air and the temprature of the plate is 20L, Compare…

A: Given DataTα=26°CTs=50°C

Q: Illustrate the concept of convection in heat transfer operation and also differentiate forced…

A: Convection Convection is a mechanism of energy transmission that combines the combined effects of…

Q: Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with…

A: Given data: Film Temperature = Tf = 300 K Velocity of flow = u = 1 m/s x = distance from leading…

Q: A hot isothermal surface is to be cooled by attaching an array of parallel, equally spaced vertical…

Q: Q5) For laminar free convection from a heated vertical surface, the local convection coeffi may be…

Q: Water at a temperature of T∞= 25°C flows over one ofthe surfaces of a steel wall (AISI 1010) whose…

Q: 1. Which is more effective in transferring heat by natural convection or forced convection?

A: In convection mode of heat transfer, heat transfer takes place by moving molecules or atoms of…

Q: -ood Luck! Thank you. If you want to cool a thin plate by natural convection quickly, will you hold…

Q: Caster oil at 36°C flows over a 6 m long and 1 m wide heated plate at 0.06 m/s. For a surface…

A: The answer is given below

Q: With the aid of diagram(s), discuss the variation of heat transfer coefficient with distance over a…

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

quickly

For external forced convection with an isothermal surface, what is the Nu# correlation equation for laminar flow if you are looking for total heat transfer?
O Mu, =0.453REP,/3
O Nu, = 0.332RE/2p/3
O Mu, = 0.664Re/2p,/a
O Mu, = 0.680RE/2p,/a

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Example 2: The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure is 20°C flows with a velocity of 8 m/s over a 1.5 m  6 m flat plate whose temperature is 140°C (Figure). Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 6-m-long side and (b) the 1.5-m side.
For internal flow with fully developed flow condition The velocity profile .................... change and the thermal profile .............................. change in the direction of flow Please fill the blank Blank 1 ( Does or does not) Blank 2 ( Does or does not )
Q2: Air at standard conditions of I atm and 27°C flows over a flat plate at 20 m/s. The plate is 60 cm square and is maintained at 97°C. Calculate the heat transfer from the plate. Answers: Q= 681 W,
Ethylene glycol at 40°C flows over a heated plate very wide, 6 m long, at velocity of 0.04 m/s. For a temperature = 90°C, determine: 1- the thickness of the hydrodynamic boundary layer at the end of the plate2- the thickness of the thermal boundary layer at the end of the plate3- the local and average heat transfer coefficient at the end of the plate4- the total heat flux transferred from the heated surface.
Prove that the thermocouple will underestimate the temperature of airflow by more than 15% but less than 30% in a large air duct if the temperature of the hot air is 1367 K, duct-wall temperature is 533 K, emissivity of the thermocouple is 0.5, and the convection heat-transfer coefficient is 114 W/m2 -K.
Air at 400C flows with a velocity of 7 m/s over a 5m long and 4m wilde surface of a flat plate whose surface temperature is 800C. Find the rate of heat transfer from the laminar flow region of the surface. (For air at 400C , V = 1.702 × 10-5 , pr = 0.7255, K = 0.02662 w/m . K). (a) 1.796 KW (b) 2.543 KW (c) 0.796 KW (d) 2.321 KW
A steam reservoir is covered by a rectangular plate (its length is 1 m and width 2 m). The steam temperature is 95o C, and it is in contact with the plate. Over the outside surface of the plate, water is flowing at a speed of 3 m/sec at a temperature of 25o C. What is the mean Nusselt number over the plate? What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate to the water?
Cold air at 5°C enters a l2-cm-diameter, 20-m-long isothermal pipe at a velocity of 2.5 m/s and leaves at 19°C. Estimate the surface temperature of the pipe.
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)?
Q3: Air flows across a 20-cm-square plate with a velocity of $ m/s. Free-stream conditions are 10-C and 0.2 atm. A heater in the plate surface furnishes a constant heat-flux condition at the wall so that the average wall temperature is 100-C. Calculate the surface heat flux and the value of h at an x position of 10 cm. Answers: Q= 1414 W, b= 13.3 Wm?.C
Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?