For gear-and-shaft system shown, both shafts AB and CD have a diameter of 1.2 in. Pulley A is subjected to a 2-kip-in. torque TA while pulley D is held fixed. Knowing that both shafts are made of a steel with G = 11.2 x 106 psi, determine: 1. The torque acting on gear B (kip-in.), 2. The torque acting on gear C (kip-in.), 3. The polar moment of inertia of the cross section of each shaft (in.“).

For gear-and-shaft system shown, both shafts AB and CD have a diameter of 1.2 in. Pulley A is subjected to a 2-kip-in. torque TA while pulley D is held fixed. Knowing that both shafts are made of a steel with G = 11.2 x 106 psi, determine: 1. The torque acting on gear B (kip-in.), 2. The torque acting on gear C (kip-in.), 3. The polar moment of inertia of the cross section of each shaft (in.“).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two solid steel shafts, each of 30-mm diameter, are connected by the gears shown. Knowing that G= 77.2 GPa, determine the angle through which end A rotates when a torque of magnitude T=200 N·m is applied at A.
The design specifications for the gear-and-shaft system shown require that the same diameter be used for both shafts and that the angle through which pulley A will rotate when subjected to a 2-kip·in. torque TA while pulley D is held fixed will not exceed 7.5°. Determine the required diameter of the shafts if both shafts are made of a steel with G= 11.2 × 106 psi and τall= 12 ksi.assuming that both shafts are made of a brass with G= 5.6 × 106 psi and τall= 8 ksi.
Two shafts, each of 7878 -in. diameter, are connected by the gears shown. Knowing that G = 11.2 ×106 psi and that the shaft at F is fixed, determine the angle through which end A rotates when a 1.4-kip·in. torque is applied at A.
Two solid shafts are connected by the gears shown. Knowing thatG = 77 GPa for each shaft, determine the angle through which end A rotates when TA=1200 N·m.
The preliminary design of a motor-to-generator connection calls for the use of a large hollow shaft with inner and outer diameters of 4 in. and 6 in., respectively. Knowing that the allowable shearing stress is 12 ksi, determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a solid shaft of the same weight, and (c) a hollow shaft of the same weight and an 8-in. outer diameter.
Three shafts and four gears are used to form a gear train that will transmit 6.7 kW from the motor at A to a machine tool at F. (Bearings for the shafts are omitted in the sketch.) Knowing that the frequency of the motor is 30 Hz and that the allowable stress for each shaft is 60 MPa, determine the required diameter of each shaft. The required diameter of shaft AB is mm. The required diameter of shaft CD is mm. The required diameter of shaft EF is mm.
A torque of magnitude T= 100 N·m is applied to shaft AB of the gear train shown. Knowing that the diameters of the three solid shafts are, respectively, dAB= 21 mm, dCD= 30 mm, and dEF= 40 mm, determine the maximum shearing stress in (a) shaft AB, (b) shaft CD, (c) shaft EF.
In the bevel-gear system shown, α = 18.43°. Knowing that the allow-able shearing stress is 8 ksi in each shaft and that the system is in equilibrium, determine the largest torque TA that can be applied at A.
A 1.5-m-long tubular steel shaft of 38-mm outer diameter d1 is to be made of a steel for which τall = 65 MPa and G = 77.2 GPa. Knowing that the angle of twist must not exceed 4° when the shaft is subjected to a torque of 660 N·m, determine the largest inner diameter d2 that can be specified in the design. The largest inner diameter d2 that can be specified is mm.
Two solid steel shafts are connected by the gears shown. Knowing that for each shaft G= 11.2 * 106 psi and the allowable shearing stress is 8 ksi, determine (a) the largest torque T0 that may be applied to end A of shaft AB and (b) the corresponding angle through which end A of shaft AB rotates.
Two solid steel shafts, each 30 mm in diameter, are connected by the gears shown in the figure. Knowing that G = 77.2GPa, determine the angle through which end A rotates when a couple of magnitude T = 200Nxm is applied to A.
A 1.5-m-long tubular steel shaft of 38-mm outer diameter d1 is to be made of a steel for which τall = 65 MPa and G = 77.2 GPa. Knowing that the angle of twist must not exceed 4° when the shaft is subjected to a torque of 540 N·m, determine the largest inner diameter d2 that can be specified in the design.