L1=1.8 L2=.9 d1=70 d2=53 Compound shaft ACB is fixed at A and consisting of two solid circular sections AC & CB, as shown, and is subjected to the given distributed torque. The diameter of part AC is DI, and the diameter of part CB is D2. The material of the shaft having a shear modulus of 69 GPa. Determine (a) the maximum shear stress (KPa) developed in shaft AB, (b) the angle of twist of point B. The values of LI, L2, DI, and D2 are given in table below for cach student. DI 50 Nm/m B C 0.2 m LI L2

L1=1.8 L2=.9 d1=70 d2=53 Compound shaft ACB is fixed at A and consisting of two solid circular sections AC & CB, as shown, and is subjected to the given distributed torque. The diameter of part AC is DI, and the diameter of part CB is D2. The material of the shaft having a shear modulus of 69 GPa. Determine (a) the maximum shear stress (KPa) developed in shaft AB, (b) the angle of twist of point B. The values of LI, L2, DI, and D2 are given in table below for cach student. DI 50 Nm/m B C 0.2 m LI L2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.The shear stress in the shaft is limited to 50 MPa. Determine the inside and outside diameters of theshaft, if the ratio of the inside to the outside diameter is 0.4. [Ans. 35 mm ; 90 mm]
Q3: The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque ofT =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r¡ = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r, = 30 mm 3. Outer tube: r; = 32mm, r, = 38mm
The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r; = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r. = 30 mm 3. Outer tube: r = 32mm, r, = 38mm
The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 4.0 ft, and c = 8.5 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
The solid 35-mm-diameter shaft is used to transmit the torques applied to the gears. The shaft is made of steel A-36 with E = 200 GPa and G = 75 GPa a. Determine the absolute maximum shear stress on the shaft. b. Determine the angle of twist of the end B with respect to end A. c. The shaft is now change d to a hollowed shaft with an outside diameter of 40 mm. What inner diameter is required to resist the same torque with the same maximum shear stress?
The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 4.5 MW when the shaft rotates at 20 rad/s, determine themaximum torsional stress in the shaft and its angle of twist.
The mean dimensions of the cross-section of the leading edge and torsion box of an airplane wing can be approximated as shown. If the wing is made of 2014-T6 (G = 19 GPa) aluminum alloy having an allowable shear stress of Tallow = 158 MPa, and the wall thickness is 12 mm. Determine the maximum allowable torque and the corresponding angle of twist per meter length of the wing.
A circular solid shaft has a diameter of 60 mm and is subjected to a torque load of 8.7 kN•m. Determine the resulting torque maximum and minimum shear stress.
A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further subjected to a torque of 10 kN-m. The maximum principal stress experienced on the shaft is closest to a) 41 MPA b) 82 MPA c) 164 MPA d ) 204 Mpa
If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa, determine the maximum allowable torques T1 and T2 that can be applied on A and B. Also, find the corresponding angle of twist of end A. Set L = 0.75 m "Mechanics of Materials, Hibbeler"
Problem: 2 A solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum torque transmitted exceeds the mean torque by 20%. Take the maximum allowable shear stress as 78 MPa.