The vertical shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into a portion CD of the shaft. Knowing that the entire shaft is made of steel for which G = 80 GPa. Determine the angle of twist at end A with respect to D (i.e 0 An). 30 mm 250 N-m 3000 N- m 0.4 m 0.2 m 44 mm- 0.6m -60 mm

The vertical shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into a portion CD of the shaft. Knowing that the entire shaft is made of steel for which G = 80 GPa. Determine the angle of twist at end A with respect to D (i.e 0 An). 30 mm 250 N-m 3000 N- m 0.4 m 0.2 m 44 mm- 0.6m -60 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 1.5-m-long tubular steel shaft of 38-mm outer diameter d1 is to be made of a steel for which τall = 65 MPa and G = 77.2 GPa. Knowing that the angle of twist must not exceed 4° when the shaft is subjected to a torque of 540 N·m, determine the largest inner diameter d2 that can be specified in the design.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
The composite shaft shown consists of a 0.2-in.-thick brass jacket (Gbrass= 5.6 × 106 psi) bonded to a 1.2-in.-diameter steel core (Gsteel=11.2 × 106 psi). Knowing that the shaft is subjected to a 5-kip·in. torque, determine (a) the maximum shearing stress in the steel core, (b) the angle of twist of B relative to end A
Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer diameter and 80mm inner diameter. The shear stress is limited to 70 MPa, and the angle of twist must not exceed 0.4 degrees in a length of one meter. Use G = 83 GPa for steel.
A hollow steel (G = 12,000 ksi) shaft has diameters of 6 in. and 4 in. and an allowable shearing stress of 9,000 psi. Determine a. the horsepower transmitted at 25 rad/sec; b. the magnitude of the angle of twist in a length of 10 ft; and c. the required number of 3⁄4-in diameter bolts for a flange coupling in which two-thirds of the bolts are on a 12-in diameter bolt circle and one-third are on a 9-in diameter circle. The allowable shearing stress in the bolts is 12,000 psi.
Under normal operating conditions, a motor exerts a torque of magnitude TF at F. The shafts are made of a steel for which the allowable shearing stress is 12 ksi and have diameters dCDE = 0.900 in. and dFGH = 0.800 in. Knowing that rD = 6.5 in. and rG = 4.4 in., determine the largest allowable value of TF.
A torque of magnitude T= 4 kN·m is applied at end A of the compos-ite shaft shown. Knowing that the modulus of rigidity is 77 GPa for the steel and 27 GPa for the aluminum, determine (a) the maximum shearing stress in the steel core, (b) the maximum shearing stress in the aluminum jacket, (c) the angle of twist at A.
The preliminary design of a motor-to-generator connection calls for the use of a large hollow shaft with inner and outer diameters of 4 in. and 6 in., respectively. Knowing that the allowable shearing stress is 12 ksi, determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a solid shaft of the same weight, and (c) a hollow shaft of the same weight and an 8-in. outer diameter.
A steel shaft must transmit 150 kW at a speed of 360 rpm. Knowing that G = 77.2 GPa, design a solid shaft so that the maximum shearing stress will not exceed 50 MPa and the angle of twist in a 2.8-m length must not exceed 3°. Consider the frequency f to be 6 Hz. The diameter of the solid shaft is -- mm
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine themaximum torque T that can be applied to the ends of the shaft without exceeding a shearstress of 70 MPa or an angle of twist of 2.5°in the 3.5-m length. Use ? =83 ??? for steel.
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter doof the solid shaft.g The required outer diameter d2of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. 3.The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
(a) For the solid steel shaft shown, determine the angle of twist at A. Use G=11.2 × 106 psi. (b) Solve part a, assuming that the steel shaft is hollow with a 1.5-in. outer radius and a 0.75-in. inner radius