For the binary cycle shown, the enthalpies are h1 = 3,195 kJ/kg; h2 = 2,265 kJ/kg; h3 = 178 kJ/kg; h4 = 184 kJ/kg; ha = 364 kJ/kg; hb = 288 kJ/kg; hc = 112 kJ/kg; and hd = 113 kJ/kg. The mass flow rate in the topping cycle is 4.1 kg/s. What is the heat transfer in the condenser? Express your answer in kW. www wwwwww 3+

For the binary cycle shown, the enthalpies are h1 = 3,195 kJ/kg; h2 = 2,265 kJ/kg; h3 = 178 kJ/kg; h4 = 184 kJ/kg; ha = 364 kJ/kg; hb = 288 kJ/kg; hc = 112 kJ/kg; and hd = 113 kJ/kg. The mass flow rate in the topping cycle is 4.1 kg/s. What is the heat transfer in the condenser? Express your answer in kW. www wwwwww 3+

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

in regard to thrust-producing engines, what is the dilemma between performance versus efficiency, referencing the propulsion efficiency equation and does an increase in one result in a decrease in the other?
10. The initial design of an IFR turbine is to be based upon Whitfield’s procedure for optimum efficiency. The turbine is to be supplied with 2.2 kg/s of air, a stagnation pressure of 250 kPa, a stagnation temperature of 800°C, and have an output power of 450 kW. At turbine exit the static pressure is 105 kPA. Assuming for air that γ ¼ 1.33 and R ¼ 287 J/kg K, determine the valueof Whitfield’s power ratio, S, and the total-to-static efficiency of the turbine.
What is the reaction equation of an impulse turbine?
In a Dual cycle, the volume at the beginning of the isentropic compression is 0.85 L and the pressure is 1 bar. If the swept volume of the cycle is 0.78 L, the pressure ratio during the constant volume heat addition process is 1.9, the volume ratio during the constant pressure heat addition process is 2.1, the specific heat ratio is y=1.3 and the work done is 455 kJ/kg, the total heat added in kJ per kg of air is: Select one: o a. 705.2 • b, 949,7 o c. 521.4 o d. 1124.5
Helium gas is used as the intermediate fluid in an ideal Brayton cycle with a regenerator. Helium emerges from the turbine at a temperature of 800 K and a pressure of 100 kPa. At the compressor outlet, the pressure of helium is 500 kPa and its temperature is 450 K. Since the efficiency of the regenerator is 80 percent; a) Compressor and turbine inlet temperatures, b) qg and q of the amount
In a Dual cycle, the volume at the beginning of the isentropic compression is 0.85 L and the pressure is 1 bar. If the swept volume of the cycle is 0.78 L, the volume ratio during the constant pressure heat addition process is 2.1, the pressure ratio during the constant volume heat addition process is 1.9, the specific heat ratio is γ=1.3 and the work done is 455 kJ/kg, the heat rejected in kJ per kg of air is:
In an ideal diesel cycle the pressure and temperature at the beginning of the adiabatic compression are 98.5kN/m^3 and 60°c, respectively.themaximum pressure attained during the cycle is 4.5MN/m^3 and the heat received during the cycle is 580kJ/kg gas.Determine for the cycle a) the volume ratio of compression b) the temperature at the end of compression c) the temperature at the end of heat reception d) the temperature at the end of adiabatic expansion e) the net work done/kg of gas f) the thermal efficiency g) the work ratio h) the mean effective pressure I) the Carnot efficiency within the cycle temperature limits.
Show that the air standard efficiency of a gas turbine can be expressed in terms ofpressure ratio only.
A turboshaft engine comprising a gas generator and a free power turbine is selected to provide propulsive power for a helicopter. The helicopter is hovering in ISA conditions at an altitude of 4100 feet. The following data applies to this engine at this static max power operating point. Intake mass flow: 8.9 kg/s Compressor pressure ratio: 24.5 Compressor isentropic efficiency: 88% Mechanical efficiency: (HP & PT shaft) 99% Combustion chamber pressure loss Combustion chamber inlet pressure 4% Combustion efficiency 98.8% Combustion chamber exit temperature: 1585K Gas generator turbine isentropic efficiency: 92% Power turbine isentropic efficiency: 90% The effects of the intake and exhaust ducts may be ignored. It may be assumed that for: Air: Cp = 1.005 kJ/kg • K, y = 1.4, R = 0.287 kJ/kg • K Combustion gases: Cp = 1.148kJ/kg • K, y = 1.333, R = 0.287 kJ/kg • K A 6% direct bleed of air from the exit of the compressor is…
A turboshaft engine comprising a gas generator and a free power turbine is selected to provide propulsive power for a helicopter. The helicopter is hovering in ISA conditions at an altitude of 4100 feet. The following data applies to this engine at this static max power operating point. Intake mass flow: 8.9 kg/s Compressor pressure ratio: 24.5 Compressor isentropic efficiency: 88% Mechanical efficiency: (HP & PT shaft) 99% Combustion chamber pressure loss Combustion chamber inlet pressure 4% Combustion efficiency 98.8% Combustion chamber exit temperature: 1585K Gas generator turbine isentropic efficiency: 92% Power turbine isentropic efficiency: 90% The effects of the intake and exhaust ducts may be ignored. It may be assumed that for: Air: Cp = 1.005 kJ/kg • K, y = 1.4, R = 0.287 kJ/kg • K Combustion gases: Cp = 1.148kJ/kg • K, y = 1.333, R = 0.287 kJ/kg • K A 6% direct bleed of air from the exit of the compressor is…
Compare the thermal efficiency of a two-stage gas turbine with regeneration, reheating, and intercooling to that of a three-stage gas turbine with the same equipment when all components operate ideally.
For a Rankine cycle, increasing maximum temperature while holding all other parameters constant will allow an engineer to make the following statements Group of answer choices Quality at the turbine exit will decrease increasing liquid water content and causing turbine erosion. Quality at the turbine exit will increase and improve turbine durability. Increasing maximum temperature increases the average temperarture at which heat is added and will increase thermal efficiency Increasing maximum tempearture will decrease required mass flow rate for a specified power output.