12) i need fast please now For the BJT amplifier below, VCEQ = 6.12 V, IcQ = 3.05mA, RE = 910 2, Vcc = 15 V,B of the Si transistor is 180 and ro = infinity.RCVCEN using commercially availableThe base resistor, RB is equivalent toresistors.O 1M in series with 91KO 680KO 820K in series with two 12KO 330K in series with 390K

For the BJT amplifier below, VCEQ = 6.12 V, IcQ = 3.05mA, RE = 910 2, Vcc = 15 V, B of the Si transistor is 180 and ro = infinity. VCE The base resistor, RB is equivalent to Q using commercially available resistors. 1M in series with 91K O 680K O 820K in series with two 12K O 330K in series with 390K

For the BJT amplifier below, VCEQ = 6.12 V, IcQ = 3.05mA, RE = 910 2, Vcc = 15 V, B of the Si transistor is 180 and ro = infinity. VCE The base resistor, RB is equivalent to Q using commercially available resistors. 1M in series with 91K O 680K O 820K in series with two 12K O 330K in series with 390K

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 5R: From a cost standpoint, which system is more economical to install: a master amplifier distribution...

See similar textbooks

Similar questions

a) Differentiate between Common Emitter (CE), Common Collector (CC) and Common Base (CB) amplifiers. b) Do the DC Analysis of the circuit below and find out the DC collector voltage?c) Do the AC Analysis of the circuit below and find out the AC collector voltage?R1=30kΩΩ=610Ω
the transistor in the circuit above has gm=0.11mS and ro=33Kohm. Given the following condition: R1=770Kohm, R2=890Kohm, RD=5.4Kohm, R3=20Kohm, R6=6.9Kohm, Rsig=2Kohm, determine the input impedance of the amplifier in Kohm.
In the circuit given in the figure, what is the voltage gain (Av) of the circuit when = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 15 kΩ and RL = 166 kΩ?NOTE-1: The output impedance r0 of the transistor will be taken into the calculations.NOTE-2: Capacitors are negligible at mid-band frequency.
Given the diferrential amplifier with a constant-current source at the emitter (instead of the resistor RE),Assume Q1, Q2, and Q3 are identical transistors with β=hfe=100 and VBE=0.7V. (a) Determine the common-mode gains Acs (for single-ended) and Acd (for double ended).For AC analysis: The constant current source has an infinite equivalent resistance.(b) Determine the common-mode rejection ratio CMRR for single-ended output.(c) Determine the common-mode rejection ratio CMRR for double-ended output.
D5 The bipolar transistors in the circuit below have β=100 and the same EBJ area. Neglect the Early effect. Find the following: a) Bias current of all transistors b) Av = vout/vin c) The amplifier’s input impedance RIN d) The amplifier’s output impedance ROUT
Figure 2 shows a typical BJT amplifier, with its parasitic capacitances displayed. The current gain of the transistor is B=150 and the voltage gain of the amplifier is Am =-125. The small signal resistances of the transistor are re =16 ohm and r0 = infinity, respectively. The values of resistors and capacitors in the figure are: R1 =80 kohm, R2 =20 Kohm, Rc = 2 Kohm, RE = 2 Kohm, Rs =50 W, RI=5 kohm, Cs=2 uF, Cc=2 uF, Ce =10 uF, Cbc =4 pF, Cbe = 10 pF, Cce =1 pF, Cwi = 4 pF, CWO = 9 pF, and Vcc = 20 V. a) Sketch a simplified circuit diagram of Figure 2 for high frequency analysis. b) Using the concept of "Miller effect capacitance", calculate the input and Output Miller effect capacitances of Figure 2, respectively. C) Determine the upper cut-off frequency of Figure 2 that is imposed by its input network only. d) Explain briefly the possible ways to increase the upper cut-off frequencv of this amplifier.
A bipolar transistor must be selected for use in a common-base amplifier with a gain of 40 dB and a bandwidth of 40 MHz. What should be the minimumspecification for the transistor’s fT ? What should be the minimum rxCμ product? (Use a factor of 5 safety margin for each estimate.)
The following Common Emitter (C.E.) amplifier is biased with a currentsource I. It has β = 100, VA = ∞, VT = 25mV, and rπ = 25kΩ. Draw the small signal equivalent circuit including the Hybrid-π with the βIb currentsource model. Label the input (Rin), output (Rout), and base (Rib) resistances. Find Rib, Rin, Rout, and the voltage gain (vo/vsig).
For the amplifier as shown, VDD = 12 V, VSS = 12 V, ISS = 20 μA, and RD = 820 kΩ. Assume IDSS = 1 mA and VP = +2 V. (a) What are the output voltages υo for the amplifier for υ1 = 0V and υ1 = 20 mV? (b) What is the maximum permissible value of υs?
In the common-emitter amplifier circuit shown in the figure, Vcc=9V, R1=27kΩ, R2=15kΩ, RE=1.2kΩ and RC=2.2kΩ. The transistor has β=100.a-) If Rsig=10kΩ and RL=2kΩ, calculate the IE value of the amplifier.b-) For small signal analysis of the transistor, find the value of Rin by deriving the π-modelc-) Calculate vo/vsig and io/ii.
Answer these questions. Explain Phase inversion of Common Emitter Amplifier. How Common Base Amplifier differs from Common Emitter and Common Collector Amplifier? Calculate Voltage Gain if RC = 150 Ω and RL = 200 Ω, IE = 1.5mA
For the MOSFET amplifier, given VDD = VSS= 8V, Rsig = 2Kohm, R3=3Kohm, Kn =K’n(W/L)= 0.5 mA/V2, Vtn= 1.2V, λ ≅ 0, Q point (0.8mA, 2.5V).Determine RD in Kohm