For the circuit given below i) Find the Thevenin equivalent circuit (i.e. Thevenin voltage and Thevenin equivalent impedance) from terminals a to b. ii) Determine the impedance Z₁, that can be placed between a and b, which will result in the maximum average power delivered to Z₁. Calculate this maximum average power. Vin + 10cos(4t) V 2 H M 12 Q 16 C1 50 mF

For the circuit given below i) Find the Thevenin equivalent circuit (i.e. Thevenin voltage and Thevenin equivalent impedance) from terminals a to b. ii) Determine the impedance Z₁, that can be placed between a and b, which will result in the maximum average power delivered to Z₁. Calculate this maximum average power. Vin + 10cos(4t) V 2 H M 12 Q 16 C1 50 mF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

From the circuit below, if R = 58, determine the maximum power absorbed by the load impedance ZL which has a power factor of 0.83. Write your answer in 4 decimal places with units.
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?
Design a power factor correction circuit with the value of parallel capacitance needed tocorrect a load of 179 kVAR at 0.85 lagging pf to unity pf. Assume that the load issupplied by a 110-V (rms), 60-Hz line.
S1) The serial impedance per unit length of a three-phase 140 km power transmission line is 0.09 + j0.88 ohm/ km and its admittance is j4.1x10-6 S / km. Power factor under 210 kV interphase voltage from the end of this energy transmission line A power of 150 MVA, which is 0.85 back, is drawn. Using this transmission line data and the T equivalent circuit model, the line Calculate the head voltage (V1), current (I1) and load angle.
A transmission line delivers 1200MW at 500kV and 85% power factor. The series impedance of the line is 0.42 + j0.65 ohms/mi and the shunt impedance to.neutral is -j0.12 x 10^6 ohms-mi. What is the velocity propagation of the line. A. 560 × 10^6 km/hr B. 890 × 10^6 km/hr C. 750 × 10^6 km/hr D. 510 × 10^6 km/hr
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this impedance is a series combination of a 120Ω resistor and another passive component. If the circuit has a sinusoidal voltage source whose frequency is 120 Hz. What is the value of the component in series with the 120Ω resistor? (Note: Express the value assuming a metric scaling of μ(10-6). Provide your answer in decimal form, up to 3 decimal places.)
In the circuit below, calculate the value of the load impedance ZL which is adjusted to transfer the maximum power and the maximum power transferred.
Exercise 1: A three-phase 3Φ transmission line has an impedance of 0.62+j35.06Ω/phase and supplies a three-phase load of 100MW with a power factor (fp) of 0.8 lagging at 200kV. Taking 100MVA and 215kV as a base, we ask: d-) Calculate the complex power consumed by the load in p.u;e-) Calculate the voltage at the emitter terminal in p.u;f-) Calculate the LT impedance taking 200MVA and 150kV as a new base. PLEASE, TYPE, HAND WRITING GETS UNDERSTANDING.
A non-reactive resistance of 60 Ω is connected in series with a 36 µF capacitor in each phase of a star-connected load.The load is connected to a 260 V, three-phase,50 Hz supply and ABC phase rotation. Use Van as the reference. 1. Calculate the impedance of the load,( Zph) in each phase in polar form, the line current,( Ia) , line current,( Ib) in polar form, line current,( Ic) in polar form. Calculate the power factor,(pf) of the load and the total power absorbed,(P) of the load 2.Calculate the total apparent power absorbed,(S) of the load
A load impedance having a constant phase angle of −36.87° is connectedacross the terminals a and b in the circuit shown. The magnitudeof ZL is varied until the average power delivered is maximized under thegiven restriction.1. Specify ZL in rectangular form.2. Calculate the average power delivered to ZL.
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.