A = 2 For the circuit given in the figure below B=75. Calculate the value of V, that produces Vo equal to 4 Vfora-) RĘ= A/2 kN, where A is last digit of your student numberb-) RE = 10 kQ,calculate;c-) VRB (voltage drop accross Rg)d-) Ise-) Icf-) Voltage VCE-g-) Propose a method to drive the transistor into saturation.+5 VRc =4 kNovoRg = 200 k2V1o wwREww

“Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

For the circuit given in the figure below B=75. Calculate the value of V, that produces Vo equal to 4 V for a-) RĘ= A/2 kn, where A is last digit of your student number b-) RE = 10 kn, calculate; c-) VRB (voltage drop accross Re) d-) la e-) Ic f-) Voltage VcŒ. g-) Propose a method to drive the transistor into saturation. +5 V Rc=4 k£2 oVo Rg= 200 k£2 Voww RE ww

For the circuit given in the figure below B=75. Calculate the value of V, that produces Vo equal to 4 V for a-) RĘ= A/2 kn, where A is last digit of your student number b-) RE = 10 kn, calculate; c-) VRB (voltage drop accross Re) d-) la e-) Ic f-) Voltage VcŒ. g-) Propose a method to drive the transistor into saturation. +5 V Rc=4 k£2 oVo Rg= 200 k£2 Voww RE ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Vin For the circuit shown, assume that Vo = 3V and that the transistor is described as follows: B-100, Va = 100V, VT = .025V. a) Determine the small signal parameters for the transistor. b) Draw the small signal model 5V 5V 300uA Vo www 4K 625 C
04:- Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE = 10 V. Use standard valued 5% resistors and draw a schematic diagram of your design. (10 points)
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
3. Write down which transistor structure each curve characteristic belongs to in the figure. Ip -VGS -VGS +VGs (c) VGS (b) (a)
Vec +12V Re 1kS2 Re 470k2 BC107 Vc Ve Figure 3: Practical Fixed Bias Transistor Circuit 2. Measure the DC voltages Vc and VB using digital multi-meters. Determine the quiescent base current, collector current, and collector- emitter voltage.
Measurements taken with an E-MOSFET indicate that when VGS=+4V, ID=8mA, and when VGS=+6V, ID=32mA. Determine the value of k.
Design a voltage-divider bias network using a supply of 28 V, a transistor with a beta of 110, and an operating point of IcQ = 6 mA and VCEQ = 6 V. Choose VẸ = 1/8 Vcc- %3D %3D %3D Use BRE = 10R2- 1. How much is the emitter voltage?
Determine VB, VE, VC, VCE, IB, IE, and IC in Figure. The 2N3904 is a general purpose transistor with a typical BDC 200 Vcc +30 V WWII VCE VB R₁ • 22 ΚΩ IC(mA) Chọn... * Chọn... * IB(UA) Chọn... * IE(MA) Chọn... ◆ Chọn... * Chọn... * Chọn... * VE VC R₂ ´ 10 ΚΩ www Rc 1.0 ΚΩ 2N3904 PDC=200 RE 1.0 ΚΩ
4 For the transistor shown in below figure, Calculate the value of R, that will just make the transistor work as closed switch. Hence Bpc= 80, VBE = 0.7V, VCE(sat) = 0.2V, Vcc= 12V, Rc= 2.7KN. la) Calculate the In and I.. Vcc RB Rc |b) Calculate Rp- B'
EHide bla This course Determine Vx and the mode of operation of the PNP transistor shown in the figure below. Assume Is = 2.5x106 A,B- 50, VA =, and Rc = 0.1 KO. Vec 2 V EX 1.2 V- Re幸 Select one: O a.1.153 V. Active Mode O60577V. Active Mode Oc 023 V. Active Mode d. None of these Oe 2306 V Saturation Mode For the circuit shewn in the figure below. assume l = 3 107A V= 26mv. B= 100, and V = The value of r-5
%3D = 13 volts, Rg = 500 KN, Rc = 6 KN and ß = 120. Assume Transistor is Silicon, VBE=0.7v. For the given circuit, Vcc +Vcc Rc RB VCE V BE a Compute for the base current Q-point, IBq (in Amperes): b. Compute for the collector current Q-point, Ico (in Amperes): c. Compute for the collector-to-emitter voltage, VCEQ (in Volts): d. Draw the DC load line with the axes and the points labeled.
Fill in the table VB VC VE Ic LE I8 fre IT gm 5V Consider the circuit given at the right. 600k 1.5k =0.7, Vauo, B=165) 100uF Vo 1k 100uF a) Perform DC analysis and calculate all VB =? VC:? branch currents, node voltages, and small signal parameters 3K VE=? Rout b) Draw a small-signal equivalent model n Vin Rin 400K c) Calculate Ri, Rout, and Ay=Vou/Vin -5V