For the circuit in the figure below, the reactance of each impendence is specified according to the frequency of the voltage source. Determine the Thevenin and Norton Equivalent circuits for the network and match a value to a specific description. OA X = 200 2 Xc = 120 n 100 sin ut v X = 300 n OB Norton's current (A) Choose... Thevenin's impedance (Ohms) Choose... If a load impedance of 20+j0 Ohms is connected at port AB, Choose.. determine the effective current (A)flowing through the load. Thevenin's effective Voltage Choose... (V) at port AB Choose. The magnitude of impedance of the parallel combination of Choose... the two inductors (Ohms)

For the circuit in the figure below, the reactance of each impendence is specified according to the frequency of the voltage source. Determine the Thevenin and Norton Equivalent circuits for the network and match a value to a specific description. OA X = 200 2 Xc = 120 n 100 sin ut v X = 300 n OB Norton's current (A) Choose... Thevenin's impedance (Ohms) Choose... If a load impedance of 20+j0 Ohms is connected at port AB, Choose.. determine the effective current (A)flowing through the load. Thevenin's effective Voltage Choose... (V) at port AB Choose. The magnitude of impedance of the parallel combination of Choose... the two inductors (Ohms)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

Exercise 11) Transform the circuit in phasor domain representation2) Determine the value of total impedance, ZT3) Determine the value of total current, IT4) Determine the value of voltage across resistor and capacitor5) Convert in rms values.
(a) Calculate the equivalent impedance of the circuit given below, if the source voltage is v(t) = 60cos1000t (b) Calculate the source current flowing in the circuit (c) Draw the phasor diagram of the current and input voltage
When it is connected in series with a pure resistor R with resistance r and inductance L, the current it draws with a sinusoidal voltage application with an effective value of 100V is 5A. The voltage across the coil and resistor element is 80V and 30V. a-Find the power and power factor consumed by the coil alone? b- Find the power consumed by the system and the power factor? c- Draw the voltage triangle, impedance triangle and power triangle?
Which can be said according to the circuit and phasor diagram given below? A) Impedance of circuit element 3 is greater than impedance of circuit element 2. B) The active power of the element 2 is greater than the total active power of the elements 3 and 5. C) The average power of element 4 is zero D) The current of element 2 is less than the total current flowing through circuit elements 3 and 5.
The variable load resistor RL in the circuit shown is adjusted for maximum average power transfer to RL. 1. a) Find the maximum average power.2. b) What percentage of the average power developed by the idealvoltage source is delivered to RL when RL is absorbing maximumaverage power?3. c) Test your solution by showing that the power developed by theideal voltage source equals the power dissipated in the circuit.
A source whose voltage is ? (?) = 50√2 cos (?? + 30 °) ? supplies a load ofimpedance ? = (4 + ?3) Ω. Saber is intended to: a) the active, reactive and apparent powerconsumed by the load. b) a capacitor power that must be installed in parallelwith the load to raise its power factor to 0.97 delayed.
For the circuit shown in Figure,a. Find the Thévenin equivalent circuit for the source.b. Find the power dissipated by the load resistor. c. What value of load impedance would permitmaximum power transfer?The voltage source is sinusoidal with frequency60 Hz, and its polarity is such that the current fromthe voltage source flows into the 10-Ω resistor.
If it is connected in series with a pure resistance R with resistance R, inductance L, the current it draws with sinusoidal voltage application with an effective value of 100V is 5A. The voltage at the ends of the coil and resistance element is 80V and 30V.a-find only the power and power factor spent by the coil?b-find the power and power factor that the system consumes?c-draw the voltage triangle, impedance triangle and power triangle? Can you solve the all a, b and c options? Please
Use the node-voltage method to find the steady-state expression for io in the circuit seen in (Figure 1) if ig= 4 cos2500t A and vg= 16 cos(2500t+90∘) V. Write the steady-state expression for io(t) as io=Iocos(ωt+ϕ), where −180∘<ϕ≤180. Find the numerical value of Io. Find the numerical value of ϕ.
Consider the voltage v(t)= 40sin(100πt+140 o ) V. a) Find the period of this voltage in millisecond and the voltage value at t=6 ms. b) This voltage is applied to the circuit below. Find VR , VC and VL phasors and and draw them on the realimaginary axis. Find vR(t) , vC(t) and vL(t) via inverse phasor, comment phase angles. c) Find active, reactive and complex power (P,Q,S) on the inductor.
1.1 We have two loads in delta and another in star in parallel, the impedances of the branches of the delta are equal and we have that RΔ=1p.u. and XΔ=0.75 p.u., while in the star we have equal values of the branches, but formed by admittances where we have the conductance in parallel GY=0.64 p.u. and inductive susceptance of BY=-j0.48 p.u. If the loads are being supplied by a positive sequence balanced three-phase source with line-to-line voltage of phases a and b of Vab=1∠ 30º, if the base values are line-to-line base voltage of 1kV and three-phase base power of 100kW. DetermineA) Line and phase voltages, line and phase currents of the load in delta, line and phase voltages of the star, line and phase currents of the star.B) Obtain separately the phasor diagram of the delta and star load with the values obtained in A), indicate on the scale that these are 1 p.u.=5cm for example.C) obtain the power triangle and the power factor separately for each load. D) Obtain the power…
An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES