Which of the following is not the advantage of Voltage Control by combined On-load Tap-Changing Transformers with off-nominal (t>1) tap locations and Reactive Power (Q) Compensators as shown in the figure below (Fig. Q1): VsZ0 v, 1:t VR ô Pc = 0 PR + jQr Compensator Qc Fig. Q1 Reducing the required Reactive power Compensation (Qc) O Improving the voltage at the Receiving End Improving the voltage stability compared to On-load Tap-Changing Transformers without Reactive Power (Q) Compensators Reducing the active power loss on the transmission line ooo

Which of the following is not the advantage of Voltage Control by combined On-load Tap-Changing Transformers with off-nominal (t>1) tap locations and Reactive Power (Q) Compensators as shown in the figure below (Fig. Q1): VsZ0 v, 1:t VR ô Pc = 0 PR + jQr Compensator Qc Fig. Q1 Reducing the required Reactive power Compensation (Qc) O Improving the voltage at the Receiving End Improving the voltage stability compared to On-load Tap-Changing Transformers without Reactive Power (Q) Compensators Reducing the active power loss on the transmission line ooo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

T1=10 Nm step input torque is applied to the mechanical system in the figure below, whose transformation ratio is given as n=1:10, at the time of t=0. Find the velocity and moment of the first and second sides. (System Parameters: B1=0.02 Nm/rad/s, B2=0.5 Nm/ rad/s, J1=0.2 kgm^2, J2=5 kgm^2)
An industrial plant is supplied by a power utility company with voltage of 7.97 kV. To monitor the plant’s performance and consumption, the utility company installed a potential transformer (PT) and a current transformer (CT) at the plant’s premises. The specs of the transformers are as shown on Fig. 1. If V , negative sequence (that is V, V) , and plant is drawing 2000 kW at 0.90 pf lagging, find the following:1.Assuming the load is Y-connected, what is the voltage VAN in volts? Enter magnitude only in 2 decimal place.
If the values of real power and reactive power is specified for a bus, then it is called as PQ bus. Select one: True False
Consider a PV module with the following external parameters at STC: Pmax = 320 W, VOC = 45 V, ISC = 8 A, NOCT =40 °C and the temperature coefficient of power is −1 W/°C. a) If the ambient temperature rises to 35 °C while the irradiance is 1,000 W/m2, what is the cell leveltemperature, calculated with the NOCT model?b) What is the new power output of the PV module under the new ambient temperature of 35 °C and 1,000W/m2irradiance?
In a certain circuit supplied from 50 Hz mains, the potential difference has amaximum value of 500V and the current has a maximum value of 10A. At the instantt=0, the instantaneous values of the p.d. and the current are 400V and 4Arespectively, both increasing positively. Assuming sinusoidal variation, statetrigonometrical expressions for the instantaneous values of p.d. and the current attime t. Calculate the instantaneous values at the instant t=0.015s and find the angle ofphase difference between the p.d. and the current. Sketch the phasor diagram (neednot be to scale).
When we talk about massive energy generation by more traditional methods, such as hydroelectric and thermoelectric plants, it is inevitable to think about environmental aspects and the entire chain involved so that the energy generated in a locality is taken to the large consumer centers. Seeking to improve this context, microgrids emerged, which can act in isolation or connected to the National Interconnected System. For consumers, the main advantages are the medium-term savings and the environmental issue. For the distributor, the impacts of microgrids are:AlternativesAlternative 1:Practically non-existent, as current equipment is efficient from an energy point of view and is digitally connected, improving the operation of the network as a whole. Alternative 2:Technical and environmental, as the consumer stops buying energy from the distributor, and the generation and transmission infrastructure becomes obsolete, generating waste for the environment. Alternative 3:Exclusively…
Given the following characteristic equation: 1+K/S(S2+2S2+8S+5)=0 (a) Using Routh method determine the range of K for which this closed loop system is stable. (b) Find the value of K for which the system has purely imaginary roots and determine the corresponding frequency of oscillations.
Consider the translational mechanical network system shown on the figure. A 1-lb force, f(t), si applied at t=0. If fv=1, find K and M such that the response is characterized by a 3-sec settling time and a 2-sec peak time. Also, what is the resulting %OS?
Please answer the following points in detail and rigorously. Instead ofresort to formulas, develop from basic principles (laws ofvoltages and currents, definition of electrical power, properties ofphasors, among others) a) Suppose that between the two terminals of an element there is a voltage v (t) and that through the terminal marked with a positive sign a current i (t). Show that if v (t) and i (t) are sinusoidal and are out of phase an angle θ, then the active power P which is consumed by this element is proportional to cosθ. b) How much is P for a pure inductor and how much for a capacitor pure? Does this make physical sense? c) When the power factor seen between two terminals is specified, Why is it necessary to indicate whether it is late or early? d) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. After, repeat the procedure but for two elements in series. e) What meaning would you give to the P consumed by an…
A 4 HP motor with a power factor of 0.8(-) operating at 100 Vrms.Find the reactant (Q) to be provided by a pure reactive element, which connected in parallel with the motor, results in a power factor at the power input of 0.95 (-). Use the + or - sign in front of your answer as appropriate.
TRUE OR FALSE? On the electric power grid, supply must equal demand at all times, otherwise frequency can swing outside the accepted limit. Storage, transmission, and demand response can help to meet this constraint.
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?