For the following system shown below, determine the characteristic equation, the risetime, settling time, and also caleulate the value of K and j so that the peak time is 1 sec,maximum overshoot is 0.2 when a unit step input is applied.KR(s)C(s)s2 + s1+jsHint: - The settling time4= 4TtsSwn

Answered: Image /qna-images/answer/d86f158f-fc3f-4dbf-a863-a2d7132d8bea.jpg

For the following system shown below, determine the characteristic equation, the rise ime, settling time, and also calculate the value of K and j so that the peak time is I sec, maximum overshoot is 0.2 when a unit step input is applied. K R(s) C(s) s2 +s 1+js Hint: - The settling time 4 = 47 Swn ts

For the following system shown below, determine the characteristic equation, the rise ime, settling time, and also calculate the value of K and j so that the peak time is I sec, maximum overshoot is 0.2 when a unit step input is applied. K R(s) C(s) s2 +s 1+js Hint: - The settling time 4 = 47 Swn ts

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.45P

See similar textbooks

Similar questions

For the system given below, a) Find K1 and K2 so that the steady-state error is zero, the settling time is one second, and the overshoot is 5% for a unit step input. b) Specify the system type and find the steady-state error a unit ramp input using the computed K1 and K2 values. "Can you explain step by step " check image "
Write the differential equation for t > 0 for iC in the given figure. Assume VS = 9 V, RS = 4 kohm, R1 = 11 kohm, and R2 = R3 = 20 kohm.
33 Determine the natural angular frequency, the damping factor, the rise time, percentage overshoot and 2% settling time for systems with the following transfer functions: (a) 100/(s + 4s + 100), (b) 49/(s + 4s + 49). * Note (that the question relates to control system)
Show that the system which is often referred to as an "incrementally linear" system below is NOT a linear system. You can use any linear relation between the input and output of the linear system block (yellow block).
For the system shown in figure (1) with unit step input. (1) Determine the value of N when the damping ratio (=0.6)? (2) Obtain rise time, peak time, and settling time for 5% of steady state error?
A) Sketch the complex plane and locate poles for 2 cases: 2 Second Order underdamped systems where both systems have the same settling time, but system #1 has a larger overshoot. B) Sketch the time response for each system in part A to a unit step input. Show clearly which system is 1 and 2. Show the relative values of the overshoot for both systems, the overshoot time, damped natural frequency and time to steady state .
For Routh Stability Criterion, Answer the following questions: 1. If the sign of the coefficient above the zero is the same as that below it? I. There is a pair of imaginary roots II. There is one sign change. III. There are roots of equal magnitude lying radially opposite in the S-Plane. IV. There is a root or roots that are imaginary or that have positive real parts. 2. If the sign of the coefficient above the zero is opposite of that below it? I. There is a pair of imaginary roots. II. There is one sign change. III. There is one sign change. IV. There is a root or roots that are imaginary or that have positive real parts.
By Differential equations An electromotive force of 100 volts is applied to an RC series circuit, in which the resistance is 50 ohms and the capacitance is 0.002 farads. Determine the load q(t) of the capacitor, if q(0) = 5C. Find the current i(t). Pls dont skip any steps even on the integrals
Given the following characteristic equation: 1+K/S(S2+2S2+8S+5)=0 (a) Using Routh method determine the range of K for which this closed loop system is stable. (b) Find the value of K for which the system has purely imaginary roots and determine the corresponding frequency of oscillations.
find vth , IN , RTH , between A and B , by using kirchhoff's law please write full detailed solution ,, thank you ,
A circuit is constructed with an AC generator, a resistor, capacitor and inductor as shown. The generator voltage varies in time as ε = Va - Vb = εmsinωt, where εm = 120 V and ω = 429 radians/second. The values for the remaining circuit components are: R = 61 Ω, C = 426 μF. The value for L is unkown. What is known is that the voltage across the generator leads the current in the circuit by φ = 48 degrees. 1) What is t1, the first time after t = 0 when the magnitude of the voltage across the inductor is maximum? 4) What is VL,max, the magnitude of the maximum voltage across the inductor? 5) What is VL = Vb - Vc, the voltage across the inductor, at time t = 0? Note that VL is a signed number.
Simplify the following expressions using Karnaugh map. Provide a complete and legible solution. 2. F(W,X,Y) = m0 + m2 + m4 + m5 + m6