For the loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam (b) the deflection at the free end, and (c) the slope at the free end. Assume that El is constant for the beam. Let wo = 7 kN/m, L = 4.0 m = 215 GPa, and I = 105 x 106 mm4. Wo

For the loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam (b) the deflection at the free end, and (c) the slope at the free end. Assume that El is constant for the beam. Let wo = 7 kN/m, L = 4.0 m = 215 GPa, and I = 105 x 106 mm4. Wo

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.7.7P: The tapered cantilever beam AB shown in the figure has a thin-walled, hollow circular cross sections...

See similar textbooks

Similar questions

.2 A ligmio.irc ii supported by two vorlical beams consistins: of thin-walled, tapered circular lubes (see ligure part at. for purposes of this analysis, each beam may be represented as a cantilever AB of length L = 8.0 m subjected to a lateral load P = 2.4 kN at the free end. The tubes have a constant thickness ; = 10.0 mm and average diameters dA = 90 mm and dB = 270 mm at ends A and B, re s pec lively. Because the thickness is small compared to the diameters, the moment of inerlia at any cross section may be obtained from the formula / = jrrf3;/8 (see Case 22, Appendix E); therefore, the section modulus mav be obtained from the formula S = trdhlA. (a) At what dislance A from the free end docs the maximum bending stress occur? What is the magnitude trllul of the maximum bending stress? What is the ratio of the maximum stress to the largest stress (b) Repeat part (a) if concentrated load P is applied upward at A and downward uniform load q {-x) = 2PIL is applied over the entire beam as shown in the figure part b What is the ratio of the maximum stress to the stress at the location of maximum moment?
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
A simple beam AB of length L and height h (see figure) is heated in such a manner that the temperature difference 7= T{between the bottom and top of the beam is proportional to the distance from support A: that is, assume the temperature difference varies linearly along the beam: T2- Tt= Tax in which 7"0 is a constant having units of temperature (degrees) per unit distance. Determine the maximum deflection SW9Xof the beam, Repeat for a quadratic temperature variation along the beam, so T2+T1= Tax
The tapered cantilever beam AB shown in the figure has a thin-walled, hollow circular cross sections of constant thickness t. The diameters at the ends A and B are dAand dB= 2dA, respectively. Thus, the diameter d and moment of inertia / at distance x from the free end are, respectively, in which IAis the moment of inertia at end A of the beam. Determine the equation of the deflection curve and the deflection 8 Aat the free end of the beam due to the load P.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam, (b) the deflection at B, (c) the deflection at the free end, and (d) the slope at the free end. Assume that EI is constant for the beam. Let w = 15 kN/m, L = 3.5 m, E = 185 GPa, and I = 110 x 106 mm4
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam AB, (b) the deflection at the free end, and (c) the slope at the free end. Assume that EI is constant for the beam. Let w0 = 6 kN/m, L = 5.5 m, E = 195 GPa, and I = 140 x 106 mm4.
For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 5.7 × 104 kN·m2 is constant for the beam; w = 8.1 kN/m, LHA = 2.7 m, LAB = 5.4 m.
Using Castigliano’s Theorem, determine the deflection equation for the cantilever beam shown below and evaluate the deflections at point B and point C.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the location of the maximum deflection, and (c) the maximum beam deflection. Assume that EI is constant for the beam. Let w = 11 kN/m, L = 4.5 m, E = 185 GPa, and I = 140 x 106 mm4.
Determine the maximum deflection of a simply supported beam carrying a hydraulic cylinder in a machine used to press bushings into a casting as shown in the figure. The force exerted during the pressing operation in 45 kN. The beam is rectangular, 35 mm thick and 150 mm high, and made of steel (E = 207 Gpa).
answer this ; Using the provided data: cross-section width w = 11 mm, cross-section hight h = 100 mm, length of the beam L =2 m , beam material’s Young’s modulus Q =243 GPa, applied bending moment ?? = 15 kN.m The value of the deflection at Point B caused by ?? ( Part I) can be calculated as
Find the slope and deflection equations for the beam shown. Determine thevertical deflection of point C. Consider P = 120 kN, l = 5m, a = 80 cm. EI = constant. Method of Double Integration