For the opamp circuit shown below figure, calculate the followings by assuming Ap=0o, Please mark two separate choices for two separate question 1. What is the required value of C, to locate the pole frequency at 0.3 MHz? 2. What is the required value of R2 to place the zero frequency of the system at a frequency twenty times the pole frequency? Circuit parameters / Devre Parametreleri R; =20 kn Vout Vin R R2 O a. C1=21.22 pF O b. R2=1.05kn O c. R2=1.25kn O d. C1=31.83 pF O e. R2=0.91ka O f. R2=1.54kn O g. C1=37.14 pF O h. C1=26.53 pF

For the opamp circuit shown below figure, calculate the followings by assuming Ap=0o, Please mark two separate choices for two separate question 1. What is the required value of C, to locate the pole frequency at 0.3 MHz? 2. What is the required value of R2 to place the zero frequency of the system at a frequency twenty times the pole frequency? Circuit parameters / Devre Parametreleri R; =20 kn Vout Vin R R2 O a. C1=21.22 pF O b. R2=1.05kn O c. R2=1.25kn O d. C1=31.83 pF O e. R2=0.91ka O f. R2=1.54kn O g. C1=37.14 pF O h. C1=26.53 pF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What must be the cutoff frequency of the low-passfilter in the figure in the EIA box if therms value of the total ac component in the outputvoltage must be less than 1 percent of the dc voltage? Assume R1 = R2 and vI = −5 sin 120πt V.
A) what is the relationship between frequency and eavelenght? ( direct or inverse) B) what is the relationship between period and frequency? ( direct or inverse)
With the aid of diagrams, show and explain how phase locking is used to generate a range of frequencies from a single stable frequency source.
When Itspice simulation of the circuit shown in the figure is performed, which of the following figures is the output representation (Vout) as given? NOTE-1: Vcc = 12 V, RO = 2.2 kO, RB 15S kO, RE 180 0 and C11 uF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.
Find the ff. on the AC circuit below having a 120Vrms as a signal source V1. a.) Total Impedance ZT b.) Current Ic , IL & IR c.) Current Total IT d.) Phasor angle e.) Voltage across each branch. VR, Vc, VL f.) Draw the phasor diagram of the circuit with complete label. g.) Plot the sinusoidal wave indicating the phase angle, showing which are lagging or leadingNote: (see attached image for the diagram and question. please answer it based on your knowledge. thank you so much!)
Choose the correct answer:9- Parellel resonant transformer test system is used whena) Large test voltages are neededb) Stable output voltage with high rate of rise of voltage is neededc) Large current is neededd) When high frequency test voltage is needede) High accuracy is needed10-Sphere gaps are used to measurea) DC, AC peak and impulse voltagesb) DC voltagesc) AC peak voltagesd) Only DC, and impulse voltagese) Only DC and AC peak voltages
Can you explain how to draw phasir addition? Thanks.
1. An impedance coil takes 144 watts at a lagging power factor of 0.6. What value of capacitance and resistance should be connected in series with the coil if the power input to the latter is to remain unchanged and the overall power factor is to be unity (in resonance)? The circuit is energized by a 120 volt, 60 cps source. 2. The given figure is to be designed to pass a wave having a frequency of 3500 cps and block a 2500 cps wave. The series inductor has an inductance of 0.0023 henry. Calculate the capacitance of the series capacitor and the parallel inductor.
i) Which type of compensator is used for feeding reactive power at the receiving end? Draw its block diagram. (ii) What is lag-lead compensator? Draw its circuit diagram and derive the expression for the transfer function of lag-lead compensator.
Question 8.46 b a. Change RL to 6.8 kΩ and Rsig to 1 kΩ and calculate the new levels of AvL and Avs. How are voltage gains affected by changes in Rsig and RL?b. For the same changes as in part (d), determine Zi and Zo, what was the effect on both impedances?
Two resistors 15 kΩ and 20 kΩ are connected at a temperature of 20°C. Calculate the equivalent noise voltage and power contributed by two resistors for a 2 Mhz bandwidth if connected in a.) series b.) parallel. Provide circuit diagram
Referring to the unity-feedback control system defined by: A. Find the following requirements in plotting the root locus. number of branches number of asymptotes asymptote real-axis intercept asymptote line angles real-axis break-away points / break-in points points at the jw-crossing B. Manually plot the root locus based on the requirements from item A C. Create a Matlab m-file to verify your root locus plot. Write down the Matlab code below