80 MPa 24 MPa (For the plane stress case in the figure; a) Draw the Mohr Circle. b) Find the principal stresses and their directions. c) Find the stresses by rotating 30 °. d-) Show the maximum shear 30° 16 MPa stress in 3-D Mohr circle.)

80 MPa 24 MPa (For the plane stress case in the figure; a) Draw the Mohr Circle. b) Find the principal stresses and their directions. c) Find the stresses by rotating 30 °. d-) Show the maximum shear 30° 16 MPa stress in 3-D Mohr circle.)

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.3P: The soil profile at a site is shown Figure P16.3. Find the total horizontal normal stresses at A and...

See similar textbooks

Related questions

Q: Q3/ Using Mohr's circle find out the principle stresses and the maximum shear stress and the stress…

Q: If the concentrated load, P = 5 kN, the resultant stress (in MPa, in integer) experienced at point…

A: given- a prestressing beam with a prestressing force acting at a distance of 100mm from neutral…

Q: Determine the maximum shearing stress (MPa) in a solid shaft of 60-mm diameter as it transmits 94 kW…

Q: Problem 5: The stresses on the x-y-axes are o, = 8 ksi, o, = 12 ksi, and T₁ = -5 ksi. Draw the…

Q: A groove is machined into the circumference of a steel shaft held in cantilever and supportin bevel…

Q: 3. Determine the principal stresses . 02 and the principal direction a, from the following stress…

Q: Water flow over the fixed surface causing the viscous velocity (in m/s) variation along y direction…

A: Given; Velocity distribution (u) = 2y-2y³+y⁴ Dynamic viscosity= 1cp

Q: Determine the normal and shear stresses at point B.

A: Consider the figure,

Q: If the output torque on the CD shaft is T ́ = 75 N-m and the motor rotates at 175 rpm, determine the…

A: Given for CD shaft diameter d2=35 mm, radius of gear R2=125 mmand torque T2=75 N-mfor EA shaft…

Q: horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the…

Q: average

Q: Determine the average normal stress and average shear stress at point C in the beam. The…

Q: PROBLEM: The uniform 2Mg bar is supported by a smooth wall at A and by a pin at B. Determine the…

A: ##Solution of a given problem-## determination of dia of smallest pin##

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250…

A: Use formula of Torsion Calculate maximum torque

Q: The simply supported beam AB as shown in Figure Q3(a) has a uniform load of intensity, w=15 kN/m…

Q: inclined at 30° to the known directions of the respectively. E = 2.1 x 10$ N/mm? and Poisson's In a…

Q: Determine the maximum shearing stress (MPa) in a solid shaft of 64-mm diameter as it transmits 110…

Q: Draw the mohr circle and find maximum principal stress Normal Stress is X direction3D45 MPa Normal…

A: Given data : The value of normal stress in X direction σX=45 MPa The value of normal stress in Y…

Q: The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 10 mm and 15…

A: Given:- cross section area of CD= 15 mm2. Cross section area of AB= 10 mm2. Maximum…

Q: Determine the magnitude of the maximum vertical force P (in kN) that can be applied to the bell…

A: Draw free body diagram Consider the moment equilibrium about point B…

Q: Sketch the normal stress distribution acting over the cross section at section a-a. 6 kip 12 kip 3…

Q: A torque of magnitude T = 1000 N·m is applied at D as shown. Shaft AB and CD have an elliptical…

Q: For the section shown, if d = 200 mm, horizontal shear force = 100 kN to the right and torque = 15…

A: To find out the total shear stress at B.

Q: Q.3 Determine the absolute maximum transverse shear stress in the beam. 6 kip 3 kip 6 in. ft

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

Q: QUESTION 2) A bending moment of M=4 kNm, tan alpha (α)=0.577, acts on the section in the figure.…

A: Solution

Q: 1. A solid aluminum alloy disk with uniform thickness has an allowable speed of wall = 40,000 RPM, a…

A: Introduction- The neutral axis has the most shear stress. The shear stress decreases as the point…

Q: Problem 2 6 kip -3 in. 12 kip Determine the normal stress developed at point A and B. Neglect the…

A: A calculating moment about x and y-axis:

Q: In the beam is gi In the ngure, a) Calculate all the internal forces in the most critical section.…

Q: his state of stress. (b) Determine the principal stresses (σp1>σp2) and the maximum in-plane shear…

A: σx=17ksiσy=-11ksiτxy=-17ksiRadius of the…

Q: A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to…

Q: Determine the maximum shear stress in the T-beam at section C. Show the result on a volume element…

A: Solution:

Q: A solid circular pole is subjected to linearly varying distributed force with maximum intensity qo…

A: Normal stress at the base 150MPa qo=6.9kN/m L=6m P=80kN

Q: The vertical bars AB and CD have a shear modulus G = 3.7 x 106 .Determine: the maximum shear stress…

Q: 2. The cross-sectional area of bar ABCD is 500 mm?. Determine the maximum normal stress in the bar.…

Q: A 40 mm T 30 mm B.

Q: . At a point, the major principal stress 66 KPa (c) and the minor principal stress is 34 KPa (T). a)…

Q: a. Determine graphically the Mohr-Coulomb shear strength parameters c' (in kN/sq m) and o'

Q: If M-50 kN-m, what is the maximum bending stress about the z-axis? (in MPa) Radius of hole 3 B…

Q: inclined at 30° to the known directions of the respectively. E = 2.1 x 10$ N/mm? and Poisson's In a…

Q: AB are 56 mm and 50 mm re

Q: If M 50 kN-m, what is the maximum bending stress abeut the AB-axis? (in MPa) R Radius of hole 3 A

Q: fM = 50 kN-m, what is the maximum bending stress about the AB-axis? (in MPa) Radius of hole 3 R 2…

Q: 1. The shaft is subjected to the axial force of 40 kN. Determine a. ta b. the normal stress in the…

A: The normal stress is defined as the ration of axial load to the cross section area of the shaft. So…

Q: 1.2 The cross-sectional area of bar ABCD is 600 mm². Determine the maximum normal stress in the bar.…

A: Given:- The cross-sectional area of the bar ABCD = 600 mm2 To determine:- The maximum normal stress…

Concept explainers

Planar Stresses

Question

80 MPa
24 MPa
(For the plane stress case in the figure; a) Draw the Mohr Circle. b)
Find the principal stresses and their directions.
c) Find the stresses by rotating 30 °. d-) Show the maximum shear
stress in 3-D Mohr circle.)
30°
)
16 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

P = 49 kips Determine the normal and shearing stress at point a, b, and c
Find the expressions to calculate the maximum normal and shear stresses for a circular profile: d (diameter)= 0.30 m
The bar has a 140 mm by 20 mm rectangular cross section. If P = 190 kN, determine the force components perpendicular (N) and parallel (V) to a-a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a-a.
If M=50 kN-m, what is the bending stress at the center of the upper hollow circle about the z-axis? (in MPa).
The soil profile at a site is shown Figure P16.3. Find the total horizontal normal stresses at A and B, assuming at-rest conditions.
A point in the ground has a total vertical (normal) stress (v) of 200 kPa, a total horizontal (normal) stress (x) of 120kPa, a horizontal shear stress (xy) of 0 kPa, and a pore water pressure (uo) of 40 kPa.(a) Determine the shear and effective normal stresses that act on a plane oriented 30 degrees clockwise fromhorizontal. Sketch the plane and draw the stresses acting on it; make sure you have the correct signconvention.(b) Determine the shear and effective normal stresses that act on a plane oriented 30 degrees counterclockwisefrom horizontal. Sketch the plane and draw the stresses acting on it; make sure you have the correct signconvention.(c) Determine the maximum shear stress and the orientation of the planes on which it acts
Determine the magnitude of the maximum vertical force P (in kN) that can be applied to the bell crank so that the average normal stress developed in the 10-mm diameter rod CD, and the average shear stress developed in the 6-mm diameter double sheared pin B not exceed 175 MPa and 75 MPa, respectively
A 0.2 m diameter shaft is supported by a smooth journal bearing at E and a smooth thrust bearing at F. Determine the maximum shear stress developed in segment BC of the shaft. 43.33 MPa 35.01 MPa 13.12 MPa 22.11 MPa
The vertical bars AB and CD have a shear modulus G = 3.7 x 106 .Determine: the maximum shear stress in the bar CD and the rotation of point C. Consider fixed points B and D.
Consider the smooth retaining wall shown below. Assume that the backfill is under active and undrained conditions and the water table is at the ground surface. Which of the following statements is true? (select all that apply) The active earth pressure is proportional to the vertical effective stress over depth. Tension crack can develop behind the retaining wall if no surcharge is applied. The resultant thrust acting on the wall only depends on the lateral earth pressure. Rankine’s theory can be used for all cases when there is some friction at the interface between the wall and the soil. When the wall is smooth, the slip surfaces are planar, and Rankine’s theory can be used.
Due to the application of line loads q1 and q2, the vertical stress increase, ∆?? , at point A is 42 kN/m2 . Determine
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 10.00 in. and a wall thickness of 0.365 in. Segment (2) has an outside diameter of 7.50 in. and a wall thickness of 0.280 in. The shaft is subjected to torques TB = 64 kip-ft and TC = 18 kip-ft, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2).