For the rechifror shown: all diode have: VY= 0.7V.rf=0 and the Maxioutput Voltoge Vm= 25 V and the input Voltage ir: Vi=160 V (pealk) f= 50H2. N:N2 D2 C [Ik Ui =160 Sin(2x50) + (v)" The turn-ratio of the transformer (N1/ N2 ) = Enter your answer The PIV rating for diodes, PIV = Enter your answer The Average diode Current IDavg =

For the rechifror shown: all diode have: VY= 0.7V.rf=0 and the Maxioutput Voltoge Vm= 25 V and the input Voltage ir: Vi=160 V (pealk) f= 50H2. N:N2 D2 C [Ik Ui =160 Sin(2x50) + (v)" The turn-ratio of the transformer (N1/ N2 ) = Enter your answer The PIV rating for diodes, PIV = Enter your answer The Average diode Current IDavg =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 1N4738A zener diode has a ZZ of 4.5 Ω. Taking the data from the datasheet we have VZ = 8.2 V with a test current, IZ, of 31 mA. What is the voltage across the zener terminals when the current is 15 mA? When the current is 55 mA? Make the representation of the values by means of their curve characteristic.
A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
A diode has wdo = 1.5 μm and φj = 0.8 V. (a) What is the depletion layer width for VR =5V? (b) For VD = −10 V?
The concentration of donor impurity atoms in silicon is Nd = 1015 cm-3. Assume an electron mobility of u, = 1300 cm?/V-s and a hole mobility of u, = 450 cm2/V-s. (a) Calculate the resistivity of the material. (b) What is the conductivity of the material?
The output of a diode used as a solar cell is given by IC =1−10−15[exp(40VC)−1] amperes What operating point corresponds to Pmax? What is Pmax? What are the values of ISC and VOC?
A diode is doped with NA=1018/cm3 on the p-type side and ND=1018/cm3 on the n-type side. (a) What are the values of pp, pn, np, and nn? (b) What are the depletion-region width wdo and built-in voltage?
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
A particular semiconductor is doped at ND=8xl0l6 cm-3 and NA=2xl0l6 cm-3 and ni=1010 cm-3. Assume complete ionization. Determine thermal equlibrium concentrations of majority- and minority-carrier concentrations. Lütfen birini seçin: Majority carrier; no= 8xl0l6 cm-3 Minority carrier; po = 1250 cm-3 Majority carrier; no = 6xl0l6 cm-3 Minority carrier; po = 1666 cm-3 Majority carrier; no= 2xl0l6 cm-3 Minority carrier; po = 5000 cm-3
Write an expression for the total photo current iPH for a diode having dc plus signal current components.
Suppose we have a 10-Hz sinusoidal voltage source, vin(t). Draw the diagram of a circuit that clamps the positive peaks to -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. List any constraints that should be observed in selecting component values. Be sure to label the terminals across which the clamped output waveform vo(t) appears.
A diode is doped with NA = 1018/cm3 on the p-type side and ND =1019/cm3 on the n-type side. (a)What is the depletion-layer width wdo? (b) What are the values of xp and xn? (c) What is the value of the built-inpotential of the junction?(d) What is the value of EMAX? Use Eq. E(x) = 1 /εs ∫ ρc(x) dxand as shown.
1. What are the main components that make up a photoresist? 2. What is a two-component resist? What are the two components? 3. What does the concept of dose involve? 4. What effect does the dose have on the molecular weight of a negativeresist? (Does it cause it to decrease or increase?5. Identify one problem that can arise when positive resist is applied to athermally grown oxide wafer (silicon substrate). How can this problembe resolved?