Answered: For the state of plane stress shown in…

For the state of plane stress shown in Figure-1. below; a) Draw Mohr's circle, b) Find the maximum in-plane shear stress, 90 MPA 60 MPA 20 MPA Figure-1

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.4P: -4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa...

See similar textbooks

Related questions

Q: * The state of plane stress at a point is represented on the element shown in the figure. The…

Q: The state of stress in a material is given in the figure. Maximum principal stress will be 45 45 5 5…

A: Given, Tensile stress in x-direction = σx = 5 units Tensile stress in y-direction = σy = 5 units…

Q: below, find the maximum shear stress and maximum normal stress

A: to find Maximum shear stress and maximum bending stress.

Q: 4. Mohrs Circle construction for generalized plane stress

A: Mohr's Circle of Generalized plane Stress.

Q: For the stress state shown. Ox = 40 MPa MPa Oy = 80 MPa Txy %3D 65 Oy Txy Using Mohr's Circle, a)…

Q: For the state of plane stress shown in Figure-1. below; a) Draw Mohr's circle, b) Find the maximum…

A: Given Data: The stress in the x-direction is, σx=-20 MPa. The stress in the y-direction is, σy=90…

Q: 450 kN and 100 kN forces were applied to the recessed beam shown in the figure. Find the stresses at…

Q: 2 -1 o =|-1 2 1 -1 2 -1 Find (a) Principal stress (b) Principal directions (c) Invariant

A: TO FIND: (a) Principal stress (b)principal direction (c) Invariants GIVEN: stress tensor:…

Q: In the figure, the normal stresses oa = 70 MPa, o, = 50 MPa, oc = 110 MPa on the faces of the…

A: Given that, σa=70 MPa,σb=50 MPa,σc=110 MPa,α=60°,β=45°, The general form of the equation of stress…

Q: a, = 200 Mpa 3D o, = 450 Mpa Tay = 200 Mpa Click here to see all formulas Part A - Determine the…

Q: Q: A block is 45 mm long, 20 mm high, 10 mm thickness. the block is subjected to a uniformly…

Q: 90 MPA 60 MPA 20 MPA

A: Given that, σx=-20 MPa,σy=90 MPa,τxy=60 MPa, Steps to draw mohr's circle: 1. Take direct stress at…

Q: Q - The mechanism of bone as a solid rod shown in figure. The diameter is 4 cm and it is subjected…

A: Acting torque on the system = 200 ×0.15 =30 Nm Bending moment at end section = 200 ×0.25 = 50 Nm the…

Q: The hollow circular pipe is subjected to two forces P=1800 and F=2500. Inner and outer radius of the…

A: The data given in this question, Force, P=1800 N, and F=2500N The inner radius of the pipe, ri=24…

Q: The state of plane stress at a point is represented by the element shown in the figure. в, - 200 Мра…

A: note: Mohr's circle is used to calculated the principle stresses

Q: the direction where the normal stress is zero

Q: A plane element is subjected to stress as shown in below figure. Determine the radius of the mohr…

Q: The state of stress of an element is shown in Figure Q5. 20 MPa 80 MPa 30 MPa Figure. 4a i.…

A: Principle Stresses : planes in which plane shear stress is zero are known as principle plane and…

Q: For the following Mohr's circle: can we find the normal stress in X, the normal stress in Y and the…

Q: B) The Figure shows Mohr's circle for a point in a physical object that is subjected to plane…

Q: In the case of plane stress given in Figure 1 a) normal and shear in the shaded plane Find their…

A: We are suppose to solve 3 sub parts only. Please post other parts as separate question.

Q: Oy = 90MPA %3D Try 60MPA %3D Ox=20MPA

A: Given Data Normal stresses σx= 20MPa σy=90MPa Shear stress fxy=60MPa Main stresses are the…

Q: Oy Ot Txy Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as ox=67,9…

A: The normal stress after rotation is given by- σn=σx+σy2+σx-σy2cos2α+τxysin2α In first case - σx=67…

Q: Plane Stress In the stress element given in Figure 3, WITH MOHR CIRCLE; (a) Determine the principal…

A: Mohr circle is a two dimensional graphical method of expressing the normal stresses and shear stress…

Q: Angle 1 Oy Tyx Figure 1 Point A(-x-direction stress 60MPA(compression), y-direction stress…

A: The given values are - σx = -60MPa , σy = 40MPa, τxy = -30MPaθ = 30° The stresses on inclined plane…

Q: Oy Ot Txy Tnt Ox On (b) (a) On the surface of a structural member, stresses are given as ox=61 MPa,…

A: Given,

Q: Quiz// For the state of stress shown in Figure below. Draw the Mohr's circle and find the principal…

Q: The state of an element is shown in figure Fig. - 1. Use to find the stresses and planes of stress…

A: The Mohr's circle is nothing but the representation of the stresses in the material on a circle. The…

Q: find the stresses acting on an element oriented at 30° Clockwise

A: Given: Plane stress conditionσx=σ1=-4740150=-31.6 MPaσy=σ2=-4740100=47.4 MPaAngle of rotation 30°…

Q: 2- The state of plane stress at a point with respect to the xy-axes is shown in Fig, find the normal…

A: To find : The normal and shear stress on section inclined at an angle of 30° Given : The stress in…

Q: A point on the surface of a mechanical component has the following state of plane stress o. = 90…

A: Given:- σx=90 MPaσy= -50 MPaτxy= 60 MPaTo find:-a) Draw mohrs circleb) Principal stresses and…

Q: Oy Ot Txy Tnt Ox On (b) (a) On the surface of a structural member, stresses are given as ox=61 MPa,…

A: Given data: Stresses on the surface of structural member σx=61 Mpa σy=32.7 Mpa τxy=-28.1 Mpa α=54.8°…

Q: 60 MPa A 80 MPa 50°

A: The plane on which the value of shear stress is equal to zero is termed the principal plane. The…

Q: 2. A figure shows a state of stress; determine the shearing stresses and normal stresses after the…

A: Given data σx=8 ksiσy=-12 ksiτxy=6 ksi Here, σ represents the normal stress and τ is the shear…

Q: The drive shaft for a truck (outer diameter 80 mm and inner diameter 25 mm) is running at 2,300 rpm…

Q: 14 ksi C ):- Draw the Mohr's Circle of the stress element shown in figure. Find:- 12 B 20ksi A 1)…

Q: Draw the Mohr's Circle (Fig. 3) as accurately as possible on a graph paper. (a) Using equation find…

Q: The stress components acting on an infinitesimal element extracted from a plate subjected to the…

A: From the given figure we can observe that the principal stress formula is given by…

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 14MPA 24 10 20 MPa The stresses…

A: Given Normal stress at X axis = 20 MPa Normal stress at Y axis = 14 MPa Slope of plane = 24 and 10…

Q: For the stress conditions given in the figure; a) Draw the Mohr Circle. b) Find the principal…

Q: Find the Normal Stress at points A, B, and C

A: To Find the Normal Stress at points A, B, and C

Q: 2. A point in a strained material is subjected to a tensile stress of 50 MPa. Find the normal and…

Q: Oy nd Txy 30 M -40 MF as n in Figure Q3. sider only the in-plane stresses. Note: the radius of the 2…

Q: 1) For the state of stress shown in figure, use the Mohr's circle method to determine (a) The…

Q: 10 MPa 9. Using Mohr's circle, for the figure at the right, determine: a) The angle to the principal…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: Q2) Look at the Mohr Circle and find (the scale is 1 cm-10 MPa) 1. Normal and shear stress at points…

A: Since we only solve upto three subparts at a time, we will solve the first three. Please specify the…

Q: Plane Stress In the stress element given in Figure, WITH MOHR CIRCLE; a- Determine the principal…

A: To Find 1.MOHR CIRCLE 2.the principal stress directions by calculating the principal stress values…

Q: Oy Ot Txy Tnt Ox On n (b) (a) On the surface of a structural member, stresses are given as ox=67,9…

A: The stress stress after rotation is given by - τnt=-σx-σy2sin2α + τxycos2α In first case-…

Q: find the principal stress , maximum in plane shear stress

Question

For the state of plane stress shown in Figure-1, below;
a) Draw Mohr's circle,
b) Find the maximum in-plane shear stress,
0 MPA
60 MPA
20 MPA
->
Figure-1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
Solve the preceding problem if the normal and shear stresses acting on element B are 56 MPa, 17 MPa, and 27 MPa (in the directions shown in the figure) and the angle is 40° (clockwise).
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
For the state of plane stress shown in Figure-1. below; now. Draw Mohr's circle, and also Determine the maximum in-plane shear stress,
1. Find the average normal stress. 2. Find the maximum in-plane shear stress.
find the normal stress and shear stress in the plane C in the element subjected to stress seen in the figure
In the case of plane stress given in Figure 1 a) normal and shear in the shaded plane Find their stresses b) principal stresses c) principal directions. d.) Results obtained Show on Mohr Circle and oriented element
I can't seem to find the shear stress at point b. Here's my work for reference.
At a point in an elastic material under strain, the stresses on the three mutually perpendicular planes are as follows:A normal tensile stress of 60 N/mm^2and shear stress of 40 N/mm2 on one plane and a normal tensile force of 40 N/mm^2and a complimentary shear stress of 40 N/mm^2 on another plane. Find the following using Mohr circle only (take 5 N/mm2 = 1 cm)a. The principal stresses and principal planes.b. The maximum shear stress and its plane.c. The normal and shear stress on a plane inclined at an angle of 30Oto major principal plane.