Force F- (4i - 2j + 7k) kips acts at point C. A(0,7,7)ft C(7.0,0)t fB(8,8,0)n Resolve force F into components parallel and perpendicular to the following lines. (Enter your answers in vector form in kips.) (a) a line that passes through points A and B kips F -( kips (b) a line that passes through points A and C F, - (L kips kips (c) a line that passes through points B and C F, -(| kips kips

Force F- (4i - 2j + 7k) kips acts at point C. A(0,7,7)ft C(7.0,0)t fB(8,8,0)n Resolve force F into components parallel and perpendicular to the following lines. (Enter your answers in vector form in kips.) (a) a line that passes through points A and B kips F -( kips (b) a line that passes through points A and C F, - (L kips kips (c) a line that passes through points B and C F, -(| kips kips

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.6P

See similar textbooks

Similar questions

Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10 lb.
A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo is unloaded by a container handling crane. Each bollard is fastened to the wharf using anchor bolts. Three cables having known tension force magnitudes F, = ll0 kN.F, = 85kN.and F, 9OkNare secured to one bollard at a point A with coordinates (0.0.45 m. 0) in the x-r-: coordinate system shown in the figure part b. Each cable force is directed at an attachment point on the ship. Force F, is directed from point A to a point on the ship having coordinates (3 m, 9 m. 0) force F, is directed at a point with coordinates (6.5 m. 8.5 m. 2 m) and force F, is directed at a point with coordinates (8 m. 9 m. S m). The diameter of each anchor bolts is 4 24 mm. (a) Find the reaction forces and reaction moments at the base of the bollard. (b) Calculate the average shear stress in the anchor bolts (in the x-: plane). Assume each bolt cart ics an equal share of the total force.
Repeat 1.3-9 but use the method of sections go find member forces in AC and BD.
As shown, an L-shaped bar is supported by a pin at joint A. The bar's dimensions are aaa = 620 mmmm and bbb = 400 mmmm , and the bar is subjected to a force with magnitude FFF = 5.05 kNkN at joint B. Ignoring the bar's weight, find the actual orientation of the applied force. What is the value of the angle θθtheta?
At 90 degrees of knee flexion, the mechanical stress at the tibiofemoral joint is 821.43 N/cm^2. If the compressive force is 1150 N, what is the magnitude of joint contact area (in cm^2)?
A copper wire has a radius of 3.5 mm. When forces of a certain equal magnitude but opposite directions are applied to the ends of the wire, the wire stretches by 5.0×10^-3 of its original length. Young's modulus for copper is 11×10^10 Pa What is the magnitude of the force on either end?
1. A circular cylinder with inside diameter of 10 cm which carries a compressive force equivalent to 400,000 N. What will be the outisde diameter of this cylinder if the allowable stress is 120 megaPascal. 2. A diagram or a curve which is a used as a reference to picture the internal forces in a beam 3. Maximum M occurs when the _______________ is ______________. 4. Within the region of positive moment, the elastic curve is concave __________ 5. There must be a/ an _________________ where the curve changes from concave down to concave up
Aluminum Rod#1 has a length L and a diameter d. Aluminum Rod#2 has a length 2L and a diameter 2d. If Rod#1 is under tension T and Rod#2 is under tension 2T, how do the changes in length of the two rods compare?
A sign for a pizza restaurant hangs from a 2.60-m long rod extended out from a building. A cable, attached to the building, is attached to the rod at a point that is 2.10 m from the hidge. (See the figure.)The mass of the rod is 5.90 kg. The mass of the sign is 9.40 kg. The angle between the building and the rod is 74.0 degrees. The angle between the cable and the horizontal is 31.0 degrees.What is the torque on the rod due to the weight of the rod alone? [Take the axis to be at the hinge.]
01: A 105cm Rod is suspended on a wall with a 5N force pulling upwards, 110 degrees away from the horizontal axis and 5cm from a 50kgm hanging object. Find the location of the C.G. away from the wall. Neglect the Mass of the rod and consider it a rigid body. Assume SSLC. 02: Considering a CCW movement is Positive, what is the total value of the Negative Moments at the point with the 50kgm object? Please answer in four decimal places, in Nm. 03: What is the value of C.G. away from the wall? (in meters, two decimal places)
During a bicep curl on a bicep curl machine, I'm curling a weight stack of 100 pounds (single arm...I'm jacked like that). At this very moment, the weight stack has a moment arm of 0.12m, my elbow has an angle of 63deg, my muscle force vector has an angle of 23deg, and it attaches 3cm below my elbow joint on my radius. How much force must my bicep create right at this moment to hold the weight stack in place?
I need help trying to solve this problem, I need to solve the Reactionary forces at these individual points marked as (RxzO) and (RxzC) I already did some of it, but I need help calculating the Moment, Shear Force, and Torque Diagram for the XZ plane and the XY plane. Also if you can explain your process it would help greatly.