Formaldehyde is commonly found in the indoor air of improperly designed and constructed buildings. If the concentration of formaldehyde in a home is 0.7 ppmy, what is the formaldehyde concentration inside the home in the unit of mg/m3?Assume T = 298 K, P = 1 atm. The molecular weight of formaldehyde is 30.

Given: Concentration of formaldehyde = 0.7 ppm To determine: Formaldehyde concentration on the unit…

Formaldehyde is commonly found in the indoor air of improperly designed and constructed buildings. If the concentration of formaldehyde in a home is 0.7 ppm,. what is the formaldehyde concentration inside the home in the unit of mg/m? Assume T- 298 K, P- 1 atm. The molecular weight of formaldehyde is 30.

Formaldehyde is commonly found in the indoor air of improperly designed and constructed buildings. If the concentration of formaldehyde in a home is 0.7 ppm,. what is the formaldehyde concentration inside the home in the unit of mg/m? Assume T- 298 K, P- 1 atm. The molecular weight of formaldehyde is 30.

Chemistry for Engineering Students

4th Edition

ISBN:9781337398909

Author:Lawrence S. Brown, Tom Holme

Publisher:Lawrence S. Brown, Tom Holme

Chapter11: Chemical Kinetics

Section: Chapter Questions

Problem 11.42PAE: Amoxicillin is an antibiotic packaged as a powder. When it is used to treat babies and small...

See similar textbooks

Similar questions

Given the following situation, what are the partial pressures of CO(g) and CO2(g)?
Glucose from molasses is fermented to alcohol using S. cerevisiae where 500 ml of CO2 (at standard temperature and pressure) is produced. If the volume of the fermentation medium is 500 ml, what is the concentration of ethanol in g/ml?
The average concentration of chloride ion in seawater is 19.353g Cl-/kg. The world health organization recommends that the concentration of Cl- ions in drinking water not exceed 250ppm. How many times as much chloride ion is there in seawater than in maximum concentration allowed in drinking water?
What is the boiling point of bromine when the external pressure is 75 kPa?Explain the significance of the triple point?
Consider the following reaction CS2(g) + 3O2(g) → CO2(g) + 2SO2(g) A mixture containing only CS2(g) and excess O2(g) at a total pressure of 100 kPa is placed in a sealed vessel. After the reaction is completed and the vessel is cooled to the initial temperature, the total pressure in the vessel drops to 80 kPa. What is the mole fraction of CO2(g) in the final mixture?
What are the variables in a van’t Hoff plot? K vs T K vs 1/T ln K vs 1/T ln K vs T
The dissociation of N2O4(g) is important in photochemical air pollution, like that common in Los Angeles, California. The reaction can be written N2O4(?) ⇆ 2NO2(?) Will the fraction of molecules dissociated increase or decrease when the temperature is raised to 555 K? Assume that ΔrH is independent of temperature.
A 1:1 mixture by moles of nitrous oxide and oxygen is often used as a sedative in dentistry. If the total pressure of this mixture in a cylinder is 2.5 atm, what is the partial pressure of each gas? STEP BY STEP WOULD BE APPRECIATED
For the reaction: A-> products: What are the units for k if m=2? *The answer must be in the form of a fraction.
Complete the following plots. The system below is at equilibrium prior to t1. The system is suddenly cooled at t1. The system responds to this stress between t and t2 until it re-equilibrates at t2. You may use this graph of paste one. N2O4(g) + 57 kJ ⇌ 2 NO2(g)
In a system where 1 particle can move between 3 states or 1 particle that can move between 5 states? Explain which system will have a greater disorder.
5 In a mixture of ethyl alcohol in water, what is the mole fraction of ethyl alcohol if it is 10% by mass in the mixture?