Formül;TL2 5 için c = cz =;(1-0,630b/a)M,(!zy .2– ly .y) + M,(1z .z – lzy.y)Tmaks =GabCzab³G'МyTM= 300 N -mB = 60°2tAIz.ly – Izy²Ox + Oy Ox – Gy21xyOx + Øy tan28, -cos20 + Txysin20 , Jort =O- dy•BIz + 0y ) +16 mmTy'y' =sin20 + Trycos20 , omaks.min =16 mmD-40 mm--40 mm→|Tmaks =+:An M pair of forces is applied to the beam shown in cross-section in a plane that makesvertical B vaccination. Find the stress at point A.O -3,37 MPaO 3,37 MPaO -4,87 MPaO 5,86 MPaO -5,86 MPa

Format TL gabG Siçin -(1- My M300 N m B-60 It o -*, cos20 + taytin20 , oprt = %*9%, tan20, - 21y 16 mm 16 mm mm- An M pair of forces is applied to the beam shown in cross-section in a plane that makes vertical B vaccination. Find the stress at point A. -3.37 MPa 3.37 MPa -4,87 MPa 5.86 MPa -5.86 MPa

Format TL gabG Siçin -(1- My M300 N m B-60 It o -, cos20 + taytin20 , oprt = %9%, tan20, - 21y 16 mm 16 mm mm- An M pair of forces is applied to the beam shown in cross-section in a plane that makes vertical B vaccination. Find the stress at point A. -3.37 MPa 3.37 MPa -4,87 MPa 5.86 MPa -5.86 MPa

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

Alplas Plastics uses an extruder in which the barrel diameter = 0.4 m and length = 6.0 m. The extruder screw rotates at 65 rev/min; it has channel depth = 0.02 m and flight angle = 16°. The plastic melt has a shear viscosity = 85 Pa-s. Determine: (a) Qmax and pmax; (b) the shape factor Ks for a circular die opening in which Dd = 0.009 m and Ld = 0.03 m; and (c) the values of Q and p at the operating point
6 Adımlı problem tekniğini kullanın. tanımlama, veri, teori, tahmin etme, çözme, doğrulama. lütfen bu tekniği kullanın
Qsafe = 187.586 MJ
How to calculate permeability according to silica bead characxteristics without knowing pressure drop? silica diameter: 2.5mm Inlet mass flow rate: 0.3m^2/min Inlet Temperature: -10 degree C
ANS : Q=114.93W/m
A windmill turns a series of slender rods fixed about one end . They are initially 2 meters long, and go at a speed of 15 revolutions per minute. I suggested making the blades 1m long to reduce the cross-sectional area of the windmill, keeping the mass the same for mechanical stress consistency. How fast are the windmill blades going now, in revolutions per minute?
5.3. Plot the variation of Ex, Gxy, νxy, mx, and my for a lamina with the following properties: EL = 35 GPa ET = 3.5 GPa GLT = 4 GPa νLT = 0.45 (Please type answer no write by hend)
1. Most bridges contain interlocking steel grates (α steel = 1.2 x 10 - 5 ºC -1 ) that allow the bridge toexpand and contract with the changes in temperature. The Golden Gate Bridge in San Francisco isabout 1350 meters long.(A) The seasonal temperature variation in San Francisco ranges from about 0ºC to 30ºC. Howmuch will the bridge expand between these two extremes?(B) What percent of the length of a subcompact automobile, 2.5 meters, does this gaprepresent?2. Selena has a fire in her fireplace to warm her 20ºC apartment. She realizes that she hasaccidentally left the iron poker (α iron = 1.2 x 10 -5 ºC -1 ) in the fire. How hot is the fire if the 0.60-meter poker lengthens 0.30 cm?3. Just before midnight, when the air temperature of 10.0ºC, Karl stops and fills the 0.0600 m 3 gastank in his car. At noon the next day, when the temperature has risen to 32ºC, Karl finds a puddle ofgasoline (βgas = 3 x 10 -4 ºC -1 ) beneath his car.(A) How much gasoline spilled out of Karl's car?…
A 30 mm diameter shaft rotates in a 30.1 mm inner diameter and 60 mm long bearing with a frequency of 5000 rpm. At that frequency it can be assumed that the eccentricity is zero. The lubricant used is SAE-30 oil at 60 ° C (μ = 4 x 10-2 Nm-2s). What is the power absorbed by the mechanism? Remember that W = C. ω, Where: ω = angular velocity = 2πf, C = conjugate (moment or torque) and 1hp = 736W = 75 kg.m/s. Expected Answer: w = 0.38hp
A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration in
solve veeeeeryyyy very fast in 15 min | I need a clear answer by hand, not by keyboard
Ultrasonic sound waves are often used in methods of nondestructive testing. For example, this method can be used to find structural faults in a steel I-beams used in building. Consider a 10.00 meter long, steel I-beam with a cross-section shown below. The weight of the I-beam is 3846.50 N. What would be the speed of sound through in the I-beam? (Ysteel = 200 GPa, βsteel = 159 GPa).