frictionlessAB从= 0.5U = 0.5dA circular cylinder of radius r=0.14 m and mass 2.2 kgis placed on two semi-circular cylinders of same radii rand mass 1.1 kg each, as shown, in a uniformgravitational field with g=9.8 m/s. The contactbetween the cylinders is frictionless, while thecoefficient of static friction u=0.5 between the semi-circular cylinders and the ground. Calculate themaximum value of distanced (in m) shown so that thearrangement can be in static equilibrium (answercorrect to 2 decimal places).

givenradius of circular cylinder r=0.14mmass of circular cylinder m=2.2kgradius of semi circular…

Answered: frictionless 1

Engineering

Mechanical Engineering

frictionless 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A disk and a ring both homogeneous with masses M1=0.94 kg and M2=M1/6 and radii R1=0.36 m and R2=R1/2, respectively, are coupled by an ideal C strap, as shown in the figure below . At a given moment, a work of modulus W=35 J is performed on the system that, starting from rest, makes the disk and the ring rotate around their symmetry axes. In view of this, answer: what is the value of the linear velocity v at the edge of the disk? Consider that the strap does not slide over the edge of objects. Choose one: Escolha uma: a. 14,80 m/s b. 12,68 m/s c. 10,57 m/s d. None of the other alternatives e. 19,02 m/s f. 16,91 m/s g. 8,46 m/s h. 6,34 m/s
A centrifugal clutch has four shoes, each of mass 0·35 kg. When at rest, the radialclearance between the shoes and the clutch drum is 15 mm and the radius to the centre ofgravity of the shoes is 225 mm. The shoes are held on retaining springs of stiffness 10kN/m and the internal diameter of the clutch drum is 600 mm. The coefficient of frictionbetween the drum and the shoes is 0·3.Determine:(a) The speed (in rev/min) at which the clutch starts to engage. For a rotational speed of 1200 rev/min:(b) The force each shoe exerts on the drum. (c) The torque transmitted. (d) The power transmitted.
A wheel tractor has a 200HP engine.If the weight of the wheel tractor is 30 tons and the weight on the drivingwheels is 50% of this weight, and it is operating at an altitute of 1000m above sea level, at an average temperature of 25 degree celcius, and at an average speed of 12km/hr. What is the maximum available rimpull if thecoefficient of traction is 0.25?. Take rimpull efficiency as 85%
A prop shaft of a heavy duty truck has two bearings which are positioned at 3 meters from each other. The shaft must rotate 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of 10 kg and 5 kg acting at the extremities of the arms 0,45 m and 0,6 m long, respectively. The planes in which these masses rotates are 1,2 m and 2,4 m, respectively, from the left end bearing supporting the shaft. The angle between the arms is 60 degrees. If the masses are balanced by two counter-masses named X and Y rotating with the shaft acting at a radius of 0,3 m and placed at 0,3 m from each bearing centre. 1.Draw a diagram illustrating the position of masses on the shaft. 2.Calculate the dynamic force in Newtons 3.Calculate the moment acting on the shaft in Newton-metre.
A motor vehicle of mass 1000 kg has road wheels of 600 mm rolling diameter. The total moment ofinertia of all four road wheels together with the half shafts is 10 kgm2, while that of the engine andclutch is 1 kg-m2. The engine torque is 150 N-m, the transmission efficiency is 90 per cent and thetractive resistance is constant at 500 N. Determine 1. Gear ratio between the engine and the roadwheels to give maximum acceleration on an upgrade of 1 in 20, and 2. The value of this maximumacceleration.
The mass of the belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN.the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N, of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley are 150° and 50cm respectively.with the addition of centrifugal tension, Design the belt drive by determine (A) velocity of the belt (B) centrifugal tension (C) tension on the slack side of the belt (D) power transmitted at this speed in kilowatts (E) maximum
the cylinder with a mass m1=2kg and radius r=0,1m is placed at a plate with mass m2=4kg. We are applying force F at this plate. Find an acceleration of the plate, when the friction coefficient μ=0,2
A prop shaft of a heavy-duty truck has two bearings which are positioned at 3 metres from each other. The shaft must rotate at 30 rad/s when the truck travels at the speed of 40 m/s. Such a shaft carries two masses of (MA = 10 kg) and (MB = 5 kg) acting at the extremities of the arms 0.45 m and 0.6 m long, respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively, from the left end bearing supporting the shaft. The angle between the arms is 60°. If the masses are balanced by two counter-masses (named X and Y) rotating with the shaft acting at a radius of 0.3 m and placed at 0.3 m from each bearing centre:
A shaft with 3 meters span between two bearings carries two masses of 10 kg and 20 kg acting at the extremities of the arms 0.45 m and 0.6 m long respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively from the left end bearing supporting the shaft. The angle between the arms is 60°. The speed of rotation of the shaft is 200 r.p.m. If the masses are balanced by two counter-masses rotating with the shaft acting at radii of 0.3 m and placed at 0.3 m from each bearing centers, estimate the magnitude of the two balance masses and their orientation with respect to the X-axis, i.e. mass of 10 kg ‎‏Note: It must be solved using the graphic method, not the equations method.
A shaft with 3 meters span between two bearings carries two masses of 10 kg and 20 kg acting at the extremities of the arms 0.45 m and 0.6 m long respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively from the left end bearing supporting the shaft. The angle between the arms is 60°. The speed of rotation of the shaft is 200 r.p.m. If the masses are balanced by two counter-masses rotating with the shaft acting at radii of 0.3 m and placed at 0.3 m from each bearing centers, estimate the magnitude of the two balance masses and their orientation with respect to the X-axis, i.e. mass of 10 kg.
A body Diagram of A nonconducting container filled with 25 kg of water at 20°C is fitted with a stirrer,which is made to turn by gravity acting on a weight of mass 35 kg. The weight fallsslowly through a distance of 5 m in driving the stirrer. Assuming that all work doneon the weight is transferred to the water and that the local acceleration of gravity is9.8 m·s−2, determine:(a) The amount of work done on the water.(b) The internal energy change of the water.(c) The final temperature of the water, for which CP = 4.18 kJ·kg−1·°C−1.(d) The amount of heat that must be removed from the water to return it to its initialtemperature.(e) The total energy change of the universe because of (1) the process of loweringthe weight, (2) the process of cooling the water back to its initial temperature, and(3) both processes together.
A. A motorcycle and rider have a combined mass of 350kg. The wheels each have a mass of 20kg, diameter of 500mm and radius of gyration of 200mm. The rider accelerates uniformly from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. The average resistance to motion, including drag, is 105 N. 1. Determine the total work done as the motorcycle ascends the incline. 2. Calculate the amount of power developed during the climb. B. At another point in its journey, the motorcycle and rider travel at 80 km/h around a left-hand bend of radius 30m. Calculate: 1. The angular velocity of each of the wheels. 2. The moment of inertia of each wheel. 3. The magnitude and effect of the gyroscopic torque produced on the bike.