From the following figure identify a lathe operation using both longitudinal & cross feed. а. Job Tool feed Taper Turning

Q: A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an…

A:

Q: The length of a workpiece is 5.25 in. is tapered in the lathe. If the shafting has .035 taper per…

A: GIVEN DATA- LENGTH OF WORKPIECE = 5.25in. TAPER PER FOOT = 0.035 WE HAVE TO FIND AMOUNT OF OFFSET

Q: Note: All dimensions are in mm Ø 34 7. 3.) A 34 mm diameter x 120 mm shafting will be turned using a…

A: Given:- Dinitial=34 mm,Dfinal,Rough=31 mm,Dfinal,Finish=30 mm,L=50 mm,rough turn:-V=30 mmin,depth of…

Q: A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 49 mm for an…

A: there are 4 subparts posted above.As per honor code and answering guidelines I can answer 1st three…

Q: A ¾” – 6 external square thread is be to cut on a lathe, calculate the minor diameter of the thread.

A: we have to calculate the minor diameter of the thread

Q: in shaft turning Steel raw material, diameter 40 mm., length 200 mm. to obtain a lathe workpiece…

A: Given, D1 = 40 mm L1 = 200 mm D2 = 35 mm L2 = 150 mm Cutting Speed, S = 25 m/min feed rate, f = 0.2…

Q: In a lathe machine,tail stock on the lathe bed forms a pair

A: lathe machine - It is a machine that rotates the workpiece about an axis of rotation with the help…

Q: 18. Lathe sizes are usually designated by the. Select one: a.LENGTH OF THE BED b.LENGTH OF WORK…

A: lathe sizes are usually designated by - Distance  between centers  swing over bed

Q: Determine the total machining time for a workpiece 30mm in diameter and the required length is 145…

A: Given: Initial length of the material→X=149 mm Initial Diameter of the material→D=38 mm Depth of cut…

Q: Identify the Lathe operation, performed without the tool moving perpendicular to the aXIS Knurling…

A: Option a is correct.

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A: Given data: The cutting speed of the tool is v=22 mmin The feed of the tool is f=0.2 mmrev The depth…

Q: 8- Which one of the operation given below is forming? a) Broaching b) Contour turning C) Taper…

A: Forming: Forming is a process in which the material is deformed plastically to take the shape of the…

Q: By what the size of upright drill press is identified?   a)largest-diameter cut b)largest-diameter…

A: Upright drill machine  An upright drill machine is used to drill the workpiece vertically. In this…

Q: ф20 O 25 $10 25 10 45

A: Machining time is given by, T=LfNwhere, L=length of operationf= feed in mm/revN=rpmGiven:V=60…

Q: For one pass turning of a shaft neck from Do= 64mm to Dr= 60 mm over an length I= 250 mm. the lath…

A: Given ,  Do = 64 mm Df = 60 mm Length of the shaft , L =250 mm Speed of cut , N =600 rpm Feed , f =…

Q: D d a° L1 SI. Parameter in Dimension in No: Drawing mm 1 d 35 2 L1 28 Cutting speed (Cs) in m/…

A:

Q: Identify the lathe operation performed when the tool moves parallel to the axis of the job is…

A: Grooving - Grooving is a method of turning that involves cutting grooves or forming a narrow cavity…

Q: A cylindrical mild steel work piece of Ø55 X 200mm undergoes a turning operation on a lathe machine…

A: Given data Diameter of work piece = 55 mmLength of work piece = 200 mmFinal diameter = 45 mmCutting…

Q: A cylindrical work bar with 4.5 in diameter and 52 in length is chucked in an engine lathe and…

A: (a) The depth of cut is, d = 0.125 in. (b) The required feed is, f = 0.010 in/rev. (c) The cutting…

Q: A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine…

A:

Q: b) Derive an expression for the "peak to valley" height Rt of a turned surface cut on a lathe with a…

A: As per Bartleby's policy in case of multiple questions I can only one. Please repost last one as…

Q: A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an…

A: there are 4 subparts posted in 1 question, as per honor code and answering guidelines I can answer…

Q: Determine the approximate compound-rest in-feed for cutting a 1½-12 UNF 2A thread

A: Compound-rest in-feed =0.7NHere, N=Number of feed=12 for 1½-12 UNF 2A threadCompound in-feed…

Q: A mild steel specimen of  Initial diameter of  30.5 mm is turned to final diameter of 27 mm for an…

A: Turing is a material removal operation in which the diameter of the workpiece is reduced. It…

Q: 1-Example: calculate the change gears to cut a single start thread of 1.5mmpitch in a lathe machine…

A: Hi and thanks for the questions. If you have asked multiple questions, we will solve the first…

Q: 3.) A 3 inches diameter 5-tooth cemented-carbide-tipped face milling cutter is to use for milling a…

A: (a) The feed rate in inch per minute is 15.28 in/min. (b) The cutting time omitting the over travel…

Q: Note: All dimensions are in mm A 34 mm diameter x 120 mm shafting will be turned using a lathe to…

A: given: Diameter of the shaft→Di=34 mm Total length of the shaft→Li=120 mm machinable length of…

Q: dentify the taper turning method in which the taper is produced by moving the tool in both…

A: Combining feeds Method    More advanced taper turning methodology is taper turning by combining…

Q: In lathe machine, the movement of the tool parallel to the axis of the job is known…

A: Basics of Lathe machine.

Q: A mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 45 mm for an…

A: Turning is a machining process used to decrease the diameter of a workpiece. Turning is done using a…

Q: 6-Internal or external tapers on a turret lathe can be turned by... a) Face turning attachment. b)…

A: Taper turning:  It is a type of machining operation in which the diameter of cylindrical object…

Q: A-List the characteristics of screw thread. B- Calculate the change gears for cutting 16 thread per…

A: Screw threads are shortened threads which are available in helical structure. These threads are…

Q: 15 1) broaching II) contour turning III) profile milling IV) thread cutting

A: generation process - the geometry of tool is impressed on to the workpiece

Q: (a) With the help of suitable sketches outline five turning operations that can be performed on a…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: D d. a° L1 El. Parameter in Dimension in lo: Drawing mm d 35 L1 28 |Cutting speed (Cs) in m/ minute…

A:

Q: In which lathe operation enlarging the already drilled hole can be produced.

A: Boring is a process in which a drilled hole made enlarged. It uses a single-point cutting tool.

Q: (a)Find number of passes to finish the entire turning operation (b) Total time required to complete…

A: for solution refer below images.

Q: the rod to 16 mm and also facing operation on both sides is done. Assume cutting speed is 30 m/min…

A: Given, L = 120 mm d = 35 mm V = 30 m/min f = 0.7 mm/rev

Q: Use the necessary data from the figure to find out the taper angle for taper turning operation?

A: It is required to determine taper angle for given part

Q: Marking tool. 10. The manufacturing process shown in the figure below is calledt a. Turning process.…

A:

Q: Identify the part of a lathe machine which is used to give longitudinal feed motion for the tool.…

A: option  ( B )   carriage

Q: A slab milling operation is performed on the top surface of a steel rectangular workpiece 12.0 in…

A:

Q: is the lathe operation, which is performed without the cutting tool moving perpendicular to the axis…

A: A lathe is a machine tool that holds and rotates a workpiece about an axis of rotation, and then…

Q: Compound-lever snips, as shown in Figure 4.13, are often used in place of regular tinner snips when…

A: When the jaw is opened, use the top handle as a frame to graphically move the snips' components.To…

Q: b) Derive an expression for the "peak to valley" height Rt of a turned surface cut on a lathe with a…

A: Ans a.) In general, we understand that surface quality is an evaluation of the surface imperfection…

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A: Given dataCutting speed Vc = 22m/minFeed f = 0.2mm/revolutionDepth of cut d = 0.5mmTaper angle α =…