2. Given that a steel cylinder of dimenslons 12.0 mm in dlameter and 70 mm long is subjected totensicn.(a) Determine the modulus of elasticity in the figure below.(b) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kNtension for ce.600500400500400E3003002002001001000.0000.0020.0040.006Strain8.000.040.030.120.160.20StrainTensile stress-strain behavior for a steel alloy.Daccri be io v ourMP MOrds the throo ctrongthanin garnin cize rad uction colidStress (MPa)Stress (MPa)

a) According to Hook's law within the elastic limit, stress is directly proportional to strain.…

Given that a steel cyInder of dimenslons 12.0 mm in dlameter and 70 mm bng is subjected to tensicn. (a) Determine the modulus of elastidity in the figure below. (E) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kN tension for e. 600 500 400 500 400 300 300 200 200 100 100 S000 0.002 0.004 0.006 Strain 8.00 0.04 0.20 0.08 0.12 0.16 Strain Tensile stress-strain behavior for a steel alloy. Sress (MPa) Stress (MPa)

Given that a steel cyInder of dimenslons 12.0 mm in dlameter and 70 mm bng is subjected to tensicn. (a) Determine the modulus of elastidity in the figure below. (E) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kN tension for e. 600 500 400 500 400 300 300 200 200 100 100 S000 0.002 0.004 0.006 Strain 8.00 0.04 0.20 0.08 0.12 0.16 Strain Tensile stress-strain behavior for a steel alloy. Sress (MPa) Stress (MPa)

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 35P

See similar textbooks

Similar questions

A piece of steel wire 100 feet long, with a cross-sectional area of 0.004 aq. in., must be stretched with a pull of 16 pounds when in use . if the modulus of elacticity of steel is 30,000 psi: a) what is the total elognation in the entire length of the wire? b) what tensile stress is producted by the pull?
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 412 mm2, 601 mm2 , and 260 mm2 respectively.Determine the change in length (in mm) of the bar if P = 30280 N.The moduli of elasticity are 81.17 GPa for bronze ,71.07 GPafor aluminum , and 202.36 GPa for steel . Round off the final answer to four decimal places.
An alloy steel having a diameter of 0.45 in. extends 0.002 in. over a gage length of 2.2 in. due to a tensile load of 3900 lb. What is the modulus of elasticity of this alloy steel? A)29,010 ksi B)27,000 ksi C)30,000 ksi D)28,000 ksi
Question 1: A 25mm diameter aluminum rod is loaded axially in tension with a load of 100kN. The rod is 4 m in length. Aluminum has a modulus of elasticity of 69GPa and a Poisson’s ratio of 0.35. 1) What is the decrease in diameter of the rod due to the applied load? 2) What is the new length of the rod?
A specimen is originally 1 ft long, has a diameter of 0.5 in., and is subjected to aforce of 500 lb. When the force is increased from 500 lb to 1800 lb, the specimenelongates 0.009 in. Determine the modulus of elasticity for the material if it remainslinear elastic.Note: Draw the given data.
A 59 kN axial load is applied to a metal bar with a rectangular cross-section, 11 mm wide by 21 mm thick. While the load is applied, the bar elongates 2.5 mm. The modulus of elasticity and the Poisson's ratio are 100 GPa and 0.35, respectively. Assuming that the bar is still behaving elastically, how long is the original length of the bar in meters? Round your answer to 1 decimal place.
Consider a 1 m-long bar of 2024-T81 aluminum alloy with a 20mm-diameter and the following property data: E=70GPa Y.S.=410MPa T.S.=480MPa %Elongation at failure=8% What will be the length of the bar under a structural load of 1.2×10^5N in tension? Your answer should be in units of meters (m).
A steel column is 3 mm long and0.4 m in diameter. It carries a loadof 50 MN. Given that the modulusof elasticity is 200 GPa, calculatethe strain.
Given that a steel cylinder of dimensions 12.0 mm in diameter and 70 mm long is subjected totension.(a) Determine the modulus of elasticity in the figure below.(b) Using the figure below, calculate the deformation in the steel cylinder subjected to 15 kNtension force.
A liquid compressed in a cylinder has a volume of 1000 cm3 at 0.95 MN/m2 and a volume of 1000 cm3 at 2.19 MN/m2. What is its bulk modulus of elasticity in MPa? Round off your answer to two decimal places.
A wire 4m long is stretched horizontally between points A and B 4m apart. A load W placed at the center of the wire produces a sag of 53.4mm,a. If the wire is 25mm2in cross-section and the Young’s modulus is 200GPa, what is the magnitude of load W?b. If the load was reduced by 40%, what will be the sag?
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.75 in2, 1.08 in2, and 0.56 in2 respectively.Determine the change in length (in inches) of the bar if P = 11599 lb.The moduli of elasticity are 30022 ksi for steel ,12071 ksifor bronze, and 10028 ksi for aluminum. Round off the final answer to four decimal places.