Given the following open loop control system k G(s) = (9 + s)s Designing a-ve feedback controller that gives a damping ratio of 0.7 yields a percentage overshoot of Select one: a. non of the choices b. 4.599% C. 4.123% d. 4.321% e. 4.637%

Given the following open loop control system k G(s) = (9 + s)s Designing a-ve feedback controller that gives a damping ratio of 0.7 yields a percentage overshoot of Select one: a. non of the choices b. 4.599% C. 4.123% d. 4.321% e. 4.637%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: The G(s) for the unity feedback is shown below. Determine the location of z, for a PD controller if…

Q: Determine if a proportional controller design for the system K(z+0.9) G(z)=-0.2)(2-0.8) can meet the…

Q: Kd =1.56 For the closed-loop system shown, and given: G(s) = 38.40 s2+ 1.47 s+ 8.00 Design a PD…

Q: 3) A plant with the given transfer functoin Gp(s) is going to be controlled by a P-controller of…

A: The solution is given below

Q: .Aregulator system has a plant: Y(s) U (s) (s+1)(s+2)(s+3) 10 Define the state-variables as: 2 x,…

A: State feedback gain matrix:

Q: 5.22 Consider a feedback system with a plant model (8 – 1)(s – 3) (8 – 2)(s+ 1)²' Use the root-locus…

A: Controller: It is used to reduce the difference between real value and desired value. This is the…

Q: 22. The unity feedback system of Figure P7.1, where G(s)- K(s² + 3s + 30) *(s+5) is to have 1/6000…

A: Given data:

Q: For the system shown in the following open-loop transfer function, find the equation of the discrete…

A: Given the open-loop transfer function as given below: Gp(s)=9s(s+9) Using the procedure performed,…

Q: Suppose the proportial gain K is tuned so that the minimum requirement for the steady state error of…

A: 11.(b) The steady state of a system is dependent on the proportional constant which is K here input…

Q: The control system G(s) = Kp / s (s+2) (s+6) has a unity feedback a. Kp is variable, discuss…

A: Here given G(s) = Kps(s+2)(s+6)For the negative unity feedback system the characteristic equation…

Q: Consider an uncertain system i(t) = x(t) + u(t), where the c;'s are constants with unknown C2 values…

Q: Q2- A feedback control system given by its closed-loop transfe K(s+15) function : (7s6+18s…

A: ROUTH-HURWITZ CRITERIA: RH criteria are used to determine the stability of the control system from…

Q: A servomotor for position control of a rotatable mass is stabilized by viscous friction damping…

A: Given f= 12 Hz ωn =2πf =2π×12=75.4 rad/sec To determine i) expression for output of the system ii)…

Q: Q2- A feedback control system given by its closed-loop transfer K(s+15) function…

A: NECESSARY CONDITIONS FOR STABILITY: All the coefficients of the Characteristics equation are…

Q: A particular control system yielded a steady state error of 0.20 for unit step input. A unit…

A: Given, steady state error for unit step input is 0.2 i.e finite. We know steady state error for unit…

Q: Butterworth response is that A. it could submit assignment at last minute B. it is very…

A: Generally butter worth filter has the maximum flat band nature response. So it can resembles the…

Q: Q 1: Explain with figures:- a) closed loop poles and stability. b) Routh's criterion. c)…

A: We need to find the closed loop poles and stability.

Q: Consider the feedback control system shown in figure below. The steady- state error for a step input…

Q: Q4. Design a PID controller for the following unity feedback control system. 1 G(s) = s3 + 5s2 + 7s…

Q: For the PD controlled positioning system, where Ge(s) = K(s + 2) and Gp(s) = s+3 s(s+1) (a) Plot the…

A: Note: As per the Bartleby Portal, I am solving first three sub parts.

Q: A controller with proportional gain K, is in series with a plant modelled as G(s) and employs a…

A: Solution-Given,G(s) = 1(s+2)(0.5s+3)

Q: Q3- For the closed-loop control system of feed forward transfer function-17 (5² +35) and Feedback…

A: Given that Gs=1.7s2+3ss2+4s2+7s+13Hs=65s+9s2 Find steady state error for unit ramp signal. Find…

Q: Which one of the following statement is correct for negative feedback? Select one: O a. A negative…

A: Need to find correct statement

Q: Q4) A particular control system yielded a steady state error of 0.20 for unit step input. A unit…

Q: Problem 2 Design a PI controller to drive the step response error to zero for the unity feedback…

A: The unity feedback system is shown below, Where, G(s)=K(s+1)(s+3)(s+10) The damping ratio of the…

Q: The forward path transfer functlon of unity feedback control system is given by Obtain an expression…

Q: - 6. The unity feedback system shown in Figure P9.1 with K(s+6) G(s) (s+2)(s + 3)(s + 5) is…

A: Given The unity feedback system with G(s) = K(s+6) / (5+2)(s+3)(5+5) is operating with a…

Q: 3. Consider a feedback control system with the plant, y(t) + 2y(t) = 2u(t), and controller, u(1) = K…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Q11 Given the following open loop control system k G(s) = s(s + 6) Designing a -ve feedback…

A: Given: In the given question they have mentioned the open loop transfer function of a closed loop…

Q: 40 new students come to a class each year. At the end of the year, 10% of the students leave the…

A: Note: As per our policy, I have attempted the first three questions.

Q: When a unit step input is applied to the closed-loop control of a system with G(s) function and…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: The loop gain of a feedback control system is given by: 130 G(s)H(s) = s2 (s+5)(s+10) %3D Determine…

Q: Given the error of Figure, plot a graph of a proportional-integral controller output as a function…

A: Given: The input waveform and parameters of a PI controller are given as KP=3, KI=4.7 s-1, p0=19.5%,…

Q: The block diagram of feedback control system shown in fig.s below find the transfer function…

Q: + JO loudspeaker is an electromechanical system that can be modeled by the electric circuit and the…

A: An electromechanical energy conversion device is one that transforms mechanical energy into…

Q: 120 6. For a simple feedback control system with G(s) = and H(s) obtain the characteristic…

Q: The block diagram in figure Q2 shows a plant G, (s) controlled by a controller Gc(s) using a unity…

Q: 5. For an unstable plant described by the following transfer function G(s) = (s – 1)(s+3)' how…

Q: The previous solutions are posted on screenshot. please refer to them for gain value. solve : An…

A: Draw the block diagram employing the PID controller as shown below:-

Q: D(s) G2(s) R(s) C(s) Gc(s) G1 (s) A feedback control system is given is given to the block diagram…

A: Given system, Where, G1(s)=2s+1G2(s)=4s+1 controlled by use of PI controller

Q: A negative feedback control system utilizing a Proportional Derivative (PD) controller was…

Q: - - For the closed-loop control system of feed forward transfer Function-17 (5² +35) and Feedback…

A: The steady state error can be calculated by using the error signal E(s) expression and the by using…

Q: (a) A P-controller with proportional gain K, is in series with a plant with the transfer function 4…

Q: Control Systems Question; 1 4. For the system given as; G(s) =: s* +2s +1 a) Obtain the state space…

A: The given system has a transfer function: Gs=1s2+2s+1 (a) State-space representation: The given…

Q: Consider the two feedback control strategies shown in Fig. (withG=GvGpGm) and the following transfer…

A: Given Gps=GDs=21-ssGvs=2Gms=1

Q: Precision grip dynamic measurements between the Index finger and the thumb have been performed using…

Q: Q2- A feedback control system given by its closed-loop transfer K(s +15) function…

A: ROOT LOCUS: The root locus technique is used to determine the stability of a closed-loop control…

Q: Q2: a) A unity feedback control system has the forward transfer function K G(s) = s(s+2)(s+3) The…

A: In the question, Unity feedback control system transfer function is given Determine the value of k…

Q: A general non-unity feedback second-order model of a linearized model of a torque- controlled crane…

Question

Given the following open loop control system
k
G(s) =
(9 + s)s
Designing a -ve feedback controller that gives a damping ratio of 0.7 yields a
percentage overshoot of
Select one:
a. non of the choices
b. 4.599%
C. 4.123%
d. 4.321%
e. 4.637%
Previous page
Next pa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Multiple Order System and Steady State Error

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 1) In a dynamic system with expression [img1] in the time domain, all initial conditions are assumed to be zero. This system will be used in the standard unit feedback control system, and the reference input is unit stepfunction, the controller is a PD controller given with [img2]. Accordingly, fill in the table below. The numerical solver (Configuration Parameters under Simulation in the menu) parameters for this stage are shown above. Table 1: Design Results Exceed (%) ?? Rise time (s) ?? Sitting time (s) ?? Peak time (s) ??
Each item below describes key characteristics of a particular system (that is, a plant transfer function). For each system, describe the effect of proportional control on the stability of the closed-loop system. Specifically, 1) what can you say for small gains, and 2) what for large gains? (E.g., stable, unstable, inconclusive.) Provide a short explanation of your answers, with sketches as necessary.
Consider the two feedback control strategies shown in Fig. (withG=GvGpGm) and the following transfer func-tions:Gp(s)=Gd(s)=2(1−s)/s,Gv(s)=2,Gm(s)=1(a)Design an IMC controller,G∗c,usingafilter,f=1/(τ꜀s+1).(b)Suppose that the IMC controller will be implemented as a controller Gc in the classical feedback control configurationof (a). Derive an expression forGcandreportitinastandard form (e.g., P, PI, or PID).
Control system! (a) For what ranges of α and β is the closed-loop system stable and (b) Given that β is fixed at some positive value, for what value of α is the closed-loop systemmarginally stable and what are the associated locations in the s-plane of those marginally stable poles?
. Question 04: A process has a liquid storage tank has an open loop transfer function given by G(s). a) Since it is desired that the closed loop system presents Mp = 10% and Ts = 4.5 sec, design a PID controller using the LGR method. Explain why this controller should be used. b) With the controller designed, obtain the closed loop transfer function of the system. Note: Consider the step-type reference and unitary and negative feedback and response.
Ignoring the “zero” in the numerator, and based only on the denominator of the closed-looptransfer-function, determine the range of constants Kp and Ki such that the rise-time of theclosed-loop system is equal (or less than) ?r =0.18 s and so that the relative damping factor ζ isequal to (or greater than) 0.8. Use the textbook approximation for the rise-time.
below is the representation of a linear control system in the state space.a) examine the controllability and observability of this systemb) estimate the unit digit response by finding the current eigenvalues of this systemC) find the feedback Matrix K= (k1 k2) that must be applied so that the system can be a two - layer root in-2
Oscillations are typical of closed-loop responses when this mode of control is used.A. proportionalb. on/off c.integral d.derivative Which mode of control effectively eliminates offsets in the controlled variable?a. integral b. on/off c. proportional d. derivative Which of the following is not a requirement for the Routh stability test? a. all coefficients positive b. even-degree polynomial c. polynomial characteristic equation d. terms arranged in standard order
3. Consider the system a) Use state feedback ? = ?? to assign the eigenvalues of ? + ?? at −0.5 ± ?0.5. Plot TT x(t) = [x1(t), x2(t)] for the open- and closed-loop system with x(0) = [−0.6, 0.4] . b) Design an identity observer with eigenvalues at −? ± ?, where ? > 0. What is the observer gain ? in this case? c) Use the state estimate ?̂ from (b) in the linear feedback control law ? = ? ?̂, where ? was found in (a). Derive the state-space description of the closed-loop system. If ? = ? ?̂ + ?, what is the transfer function between ? and ?? TT d) For ?(0) = [−0.6, 0.4] and ?̂(0)= [0, 0] , plot ?(?), ?̂ (?), ?(?), and ?(?) of the closed- loop system obtained in (c) and comment on your results. Use ? = 1, 2, 5, and 10, and comment on the effects on the system response. Remark: This exercise illustrates the deterioration of system response when state observers are used to generate the state estimate that is used in the feedback control law.
Please dont try to solve it with Chatbot GPT, it does not give the correct answers g) Suppose you want to design the controller C(s) to produce a closed-loop response to a reference step input that has no more than 30% maximum overshoot (Mp ≤ 0.30) and a peak time of no more than 8 sec (tp ≤ 8). Given the specifications on Mp and tp , compute the constraints on the damping ratio ζ and the damped natural frequency ω, assuming that the closed-loop system is approximated as a 2nd-order underdamped system. Sketch the allowable regions in the complex plane (the s-plane) that these constraints define, and shade in the regions where the poles should not be placed. Submit your calculations and your sketch.
A gas stove system has to be in automation form to enhance easy regulation and control. Make a drawing of a functional block diagram which shows the output and input transducers, the plant, controller response & reference.
The characteristics equation of a closed loop system is s2+4s+16=0. The natural frequency of oscillation and damping constant respectively are ?