Given the following Resistances and Inductors in Series and Voltage Source:R1 = 46 ohmsR2 = 33 ohmsL1 = 0.3 Henry12 = 0.34 HenryVs = 10 VoltsFrequency = 95 HzWhat is the Total Reactance? Given the following Resistances and Inductors in Series and Voltage Source:R1= 46 ohmsR2 = 33 ohms%3DL1= 0.3 HenryL2 0.34 HenryVs10 VoltsFrequency = 95 Hz%3DWhat is the Total Reactance?

Answered: Image /qna-images/answer/40825b1f-d451-475b-b274-28a514d8b9db.jpg

Answered: Given the following Resistances and…

Given the following Resistances and Inductors in Series and Voltage Source: R1 = 46 ohms R2 = 33 ohms L1 = 0.3 Henry 12 = 0.34 Henry Vs = 10 Volts Frequency = 95 Hz What is the Total Reactance?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 1RQ: What is the phase angle relationship of current and the voltage dropped across a pure resistance?

See similar textbooks

Related questions

Q: f galvanometer is 8 mm / µ A. If the internal re cer is 80 ohm then the deflection of galvanome n…

A: In this question P,Q,R,S given..V given..Current sensitivity and internal resistance of galvanometer…

Q: R = 40 L=2 H 20 Volts C = 0.5 F

Q: Three resistors X, Y and Z are connected in series-parallel with X in series with the parallel…

Q: 13. Figure 3 is a 120/240 volt 3 wire service. What is the current on the neutral conductor? Figure…

A: Applying KCL at the neutral node ,

Q: A coil takes a current of 4 A when 24 V d.c. are applied and for the same power on a 50-Hz a.c.…

A: PART (a): For a Coil, Z=R+jXL Where, R= Resistance of the coil, XL=Inductive reactance of the coil.…

Q: An inductance of L Henries and a resistance of 15 ohms are connected in series with EMF of 135…

A: Apply KVL in loop and write the differential equation relating inductor current. Now using linear…

Q: √==G Circuit 1 00 Circuit 2 In the circuits shown in the diagrams above, an uncharged capacitor is…

Q: The relation between electric intensity E, voltage applied V and the distance d between the plates…

A: Electric field intensity E is defined as ratio of Voltage applied V and distance d between the…

Q: 5Ω Ic IR IL = 120 VZ0°( Xc 30 Ω R 60 Ω Vr

Q: DC Voltage has ______ polarity Types of grounds in electrical/electronic circuits.

A: DC voltage has fixed polarity. The polarity is either positive on one terminal and negative on…

Q: calculate the magnitude of the voltage drop across the jik ohm inductor 1.2 k2 jl k2 -j4.7 kQ j2.2…

Q: d) What is the value of R in this circuit e) Is the circuit behavior, more capacitive or inductive?…

Q: What will be value of the current flowing through the following circuit:

A: Since the inductor is connected across the voltage source, the voltage across the inductor will be…

Q: Across a 230v, 60Hz power supply is a 15 ohm non-inductive resistor. What is the equation of the…

A: We need to find out current through resistor for given voltage .

Q: A pure element is connected across an AC signal. CH1 and CH2 measures the voltage and current, r CH1…

A: Given waveform shown CH1 settingsVolts/Div :83 vTime/Div :3 msProbe Settings: X1CH2…

Q: A tungsten lamp filament has a temperature of 2050 degree celcius and a resistance of 500 ohms when…

A: Given parameters are: For Temperature, t1=2050oC Resistance, R1=500Ω For Temperature, t2=20oC…

Q: What is the thermal voltage equal to at T 400K? 25mV 25.9mV 34.5mV 40.2mV

A: We have to find the thermal voltage at 400K. as we know Thermal Voltage = k.Tqwherek =boltzmann…

Q: What is the resistance of a No. 14 iron wire, 600 feet long at 248 degrees Fahrenheit.

A: The length of No. 14 iron wire is 600 feet, which is equal to 182.88 in meters. We know that the…

Q: What is the Total Reactance in ohms?

Q: . When a circuit is interrupted, the _______ returning to the source is also interrupted. A. rating…

A: It is asked to choose the correct answer from the given options.

Q: A current of - 8 + 62-V (sin (wt + 30°)) A is passed through three meters. The respective readings…

Q: 19. Determine the resistor and inductor voltages for the circuit shown in Figure 3.33. Figure 3.33 4…

Q: Alternating current is __________. Select one: A. AN ALTERNATING FLOW OF ELECTRONS B. ELECTRONS…

Q: 3. A resistance of R ohms and an inductance of 0.5 henry are connected in series with an emf of 40…

Q: What will be different if there is no "Ce"? Can you make a solution based on the absence of "Ce"?…

A: given, β=120VBE=0.7VVA=100VCμ=1pFfT=600MHz

Q: If Be = 1.1 Tand Hc = 260 A-t, then the relative permeability is: Hr=

A: Flux density, Bc = 1.1T Magnetic field intensity, Hc = 260 A-t

Q: 1- Use the Oscilloscope (CRO) waveforms photos for the circuit in figure 1, to discuss the input,…

A: During On time circuit-:

Q: 5. A coil takes a current of 4 A when 24 V d.c. are applied and for the same power on a 50-Hz a.c.…

Q: Solve for the value of inductive reactance if R1 = 482 ohms, R2 = 21 ohms and L3 = 5.5 mH.

Q: Problem 76: A resistance of 120 ohms is supplied by a 250 V, 60 Hz source. Determine the equation of…

A: Given R = 120 ohms Vmax = 250 V and f = 60Hz or W = 120pi. Find VR and IR ?

Q: An alternating voltage e= 120 sin 314t is applied to a circuit in which an ohmic resistance of 30ohm…

Q: nèstion 15 What is the value of the conductance of z = 10 +5j ? 0.1 None of the answers 0.2 A Moving…

A: Conductance is inverse of resistance. G= 1/R

Q: 5. A circuit has a resistance of 20 ohm and a reactance of 30 ohm. What is the power factor of the…

Q: Find the current passing R2 in mA (when voltage source reaches the positive peak value= Vj). V2 Si…

A: Consider the given circuit,

Q: Given the following Resistances and Inductors in Series and Voltage Source: R1 = 74 ohms %3D R2 = 69…

Q: A string of suspension insulators consists of three units. The capacitance between each link pin and…

Q: The relation between electric intensity E, voltage applied V and the distance d between the plates…

Q: Given the following Resistances, Inductors and Voltage Source are parallel to one another:…

A: Given:

Q: Q1. Referring to the Figure Q1, answer the following questions: VI V1(@t) 40 V

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: resistor R is connected in parallel with a 10-ohm inductive reactance. The combination is then…

A: We need to find out the value of resistance for given circuit

Q: The voltage across a solenoid is shown in the figure, measured by an oscilloscope. What would be the…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Determine the power across 10 volts supply after solving the circuit by nodal analysis.

Q: Q1: For the network shown in figure (1), 1. If the switch is closed, write the mathematical…

A: Current expression through inductor can be expressed as: i(t)=i∞+i(0+)-i(∞)e-tτ Where i∞ is steady…

Q: Determine the voltages Vx and Vy. Complete solution with explanation.

A: In this question we will find unknown voltages..

Q: Question 4 a) A iii. B Figure 4 Figure 4 shows the graph of the ripple current. Answer the following…

A: Full wave Bridge Rectifier Circuit :

Q: (b) The diagram shows part of an electrical circuit. 20 mA 30 mA 15 mA Determine the magnitudes of…

Q: A 120 V, 60 W lamp is to be operated on 220 V, 50 Hz supply mains. For the lamp to operate in…

Q: A charge of 15C flow in a conductor in .5 *:2min, then the current produced is 125A O 0.125A O 12.5A…

A: I=q/t Q= 15C t= 2min = 120sec

Question

100%

Given the following Resistances and Inductors in Series and Voltage Source: R1 = 46 ohms R2 = 33 ohms L1 = 0.3 Henry 12 = 0.34 Henry Vs = 10 Volts Frequency = 95 Hz What is the Total Reactance?

Given the following Resistances and Inductors in Series and Voltage Source:
R1
= 46 ohms
R2 = 33 ohms
%3D
L1
= 0.3 Henry
L2 0.34 Henry
Vs
10 Volts
Frequency = 95 Hz
%3D
What is the Total Reactance?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
What is the phase angle relationship of current and the voltage dropped across a pure resistance?
Given the following Resistances and Inductors in Series and Voltage Source: R1 = 14 ohms R2 = 20 ohms L1 = 2 Henry L2 = 2 Henry Vs = 946 Volts Frequency = 8 Hz What is the Amplitude of the Current in amperes?
(a) (i) Capacitance in pF if dielectric material is air = Answer and unit for part 1 (ii) Capacitance in pF if dielectric with relative permittivity of 3.7 is used = Answer and unit for part 2 Q23 (b) Equivalent Capacitance (Ceq) = Answer and unit for part 3
The resitance of a wire is 25 ohms at 50°C and 20 ohms at 30°C. Determine the temperature coefficient at 24°C. Note: DRAW THE DIAGRAM
Identify the characteristics of AC and DC voltage. Runs at a higher temperature Answer 1Choose...DCAC More dangerous to transfer Answer 2Choose...DCAC Easy to produce Answer 3Choose...DCAC Easier to transform voltages Answer 4Choose...DCAC Voltage remains at a constant value Answer 5Choose...DCAC Cheaper to produce
An inductance of 2 henries and a resistance of20 ohms are connected in series with an emfof E volts. If the current is zero at time, t = 0,find the current at the end of 0.01 sec if E =100sin150t volts.
4.Suspension string has 3 units. Each unit can with stand a maximum voltage of 11kV. The capacitance of each joint and metal work is 30 percent of the capacitance of each disc. Find i) Maximum line voltage for which the string can be used?
please give solution and answer correctly. tysm po
1)Did you find the current i2 (t)? 2)Did you find the complex power over inductance?
The pure element is either resistor, inductor, or capacitor. Determine the values of either the resistance, inductance, or capacitance. Write the magnitude only in micro (µ) in four decimal places. the correct answer is 96.1171 please show the solution thank you.
An inductance of 2 Henries and a resistance of 20 ohms is connected in series with an emf of E volts. If the current is zero at time t = 0, find the current at the end of 0.01 sec if (a) E = 100V and (b) 100 sin 150t V.