Q1: An aluminum pan whose thermal conductivity is 237 W/m-°C has a flat bottom whose diameter is 20 cm and thickness 0.6 cm. Heat is transferred steadily to boiling water in the pan through its bottom at a rate of 700 W. If the inner surface of the bottom of the pan is 105°C, determine the temperature of the outer surface of the bottom of the pan.

Q1: An aluminum pan whose thermal conductivity is 237 W/m-°C has a flat bottom whose diameter is 20 cm and thickness 0.6 cm. Heat is transferred steadily to boiling water in the pan through its bottom at a rate of 700 W. If the inner surface of the bottom of the pan is 105°C, determine the temperature of the outer surface of the bottom of the pan.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material in which energy is released at a uniform rate per unit volume , is
1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.
In determining the average rate of heating of a tank of 20% sugar syrup, thetemperature at the beginning was 20°C and it took 30 min to heat to 80°C. Thevolume of the sugar syrup was 50 ft3 and its density 66.9 lb/ft3. The specific heat ofthe sugar syrup is 0.9 Btu lb-1°F-1.(a) Convert the specific heat to kJ kg-1°C-1.(b) Determine the rate of heating, that is the heat energy transferred in unit time, in SI units (kJ s-1)
Example 9: A 2-kW resistance heater wire whose thermal conductivity is k = 15 W/m ·°C has a diameter of D = 4 mm and a length of L = 0.5 m, and is used to boil water. If the outer surface temperature of the resistance wire is Ts = 105°C, determine the temperature at the center of the wire.
THERMOFLUID A student living in a 3-m X 4-m X 4-m dormitory room turns on her 100-W fan before she leaves the room on a summer day, hoping that the room will be cooler when she comes back in the evening. Assuming all the doors and heat trans windows are tightly closed and disregarding any heat fer let through the walls and the windows, determine the temperature in the room when she comes back 8 h later. Use specific heat values at room temperature, and assume room to be at 100 kPa and 20°C in the morning she leaves.
What is the ton of refrigeration required to cool 15,000 lbm of fresh pork from a temperature of 89°F to 32°F in one day? Specific heat above freezing of fresh pork is 0.68 BTU/lbm-°F.
2. A large sheet of glass 2” thick is initially at 300oF throughout. It is plunged into a stream of running water having a temperature of 60oF. How long will it take to cool the glass to an average temperature of 100oF. For glass k = 0.40BTU/ft-hroF, ρ = 155 lb/ft3 and Cp = 0.20 BTU/lboF.
Located near the bottom of an insulated cylinder is a rigid plate. Between the rigid plate and the bottom of the cylinder is 0.4 kg (ma) of air at 250 kPa (Pa1) and 300 K (Ta1). Between the rigid plate and a moveable piston 0.5 kg (mw) of superheated water vapor at 300 Celsius (Tw1) and 100 kPa (Pw1) is added. Consider these to be the initial conditions (state 1) of this multi-component system. The rigid plate is conductive allowing heat to pass between the air and water vapor, but the piston is well insulated. The water vapor is manually compressed in an unknown process until the volume of water vapor (Vw2) is halved and the pressure is 200 kPa (Pw2), at which point the air and water vapor are in temperature equilibrium.Determine the following:A. The change in entropy of air and water in kJ/K B. The change in entropy of the combined system, S2-S1, in kJ/K, neglecting the mass of the rigid plate C. The entropy produced, σ, of the combined system during the process
By superheating the stream to a high temperature, the average steam temperature during heat rejection can be increased. True or False
A cylindrical vessel (D=98,4 cm) is filled with water (ρ=1000 kg/m3, c=4.187 kJ/kg.K) to a depth of 113,64 cm. The initial temperature of the water is 15°C. Determine the time [min] required to increase the water temperature to 50°C when it is immersed into tank, filled with oil at 105°C. (NOTE: The overall heat transfer coefficient between the oil and the water is 284 W/m2.K. The surface area is 4.2 m2.)
Consider a heat engine with a piston chamber that has a diameter of 30 mm, a cold reservoir at 285 K and hot reservoir at 350 K. It is also equipped with a metal can cylinder that has a volume of 0.0002 m3. How many moles of air are present in the system if the metal cylinder is in the cold tank and the measured pressure and the total air volume are 104160 and 0.00015 m3, respectively?
In a power plant, pipes transporting superheated vapor are very common. In a certain plant, superheated vapor is flowing at a rate of 0.3 kg/s inside a 5 cm diameter pipe of 10 m length. The air in the plant is maintained at 20oC while the surface temperature of the pipe is 100oC. If the temperature drop between the inlet and exit of the pipe is 30oC and the specific heat capacity of the vapor is 2190 kJ/kg.K, determine the convective heat transfer coefficient at the pipe surface. If necessary, how could this coefficient be increased?