he following half-wave rectifier circuit of has an ideal transformer inserted between the source an emainder of the circuit. The source is 240 V ms at 50 Hz, and the load resistor is 20 ohm. a) Determine the required turns ratio of the transformer such that the average load current is 12 A b) Determine the average current in the primary winding of the transformer. c) The power delivered by the source d) The power absorbed by the load

he following half-wave rectifier circuit of has an ideal transformer inserted between the source an emainder of the circuit. The source is 240 V ms at 50 Hz, and the load resistor is 20 ohm. a) Determine the required turns ratio of the transformer such that the average load current is 12 A b) Determine the average current in the primary winding of the transformer. c) The power delivered by the source d) The power absorbed by the load

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, The transformer is specified to have a 12 V rms secondary voltage for the standard 110 V across the primary. (2nd Approximation)
An ideal single-phase full wave rectifier circuit has a non-inductive resistanceload, negligible tube drops and no transformer losses. What is therectification or conversion efficiency in percent?
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
Describing the concept of discontinuous conduction mode in power converters, how does continuous conduction mode differ?Make a DC-DC converter circuit that operates in discontinuous conduction mode.
A 3.3-V, 30-A dc power supply is to be designed with a ripple of less than1.5percent. Assume that a half-wave rectiﬁer circuit (60 Hz) with a capacitor ﬁlter is used. (a) What is the size of the ﬁlter capacitor C? (b)What is the PIV rating for the diode? (c)What is the rms value of the transformer voltage needed for the rectiﬁer?(d) What is the value of the peak repetitive diode current in the diode? (e) What is the surge current at t =0+?
Explain the operation of both signal- and three-phase rectifier circuit by making reference to the sketched waveform.
1- A testing transformer 220 V/100 kV (rms), 50 Hz is supplying a half wave rectifier circuit. If the load resistance is 5 MΩ, find: a- The value of the smoothing capacitor so that the time constant is 10 times the supply periodical time. b- The rated peak inverse voltage (PIV) of the rectifier. c- The number of series connected rectifiers if the rated PIV of a rectifier is 20 kV. d- The ripple and the output voltages. the sub-parts to be solved.
1- A testing transformer 220 V/100 kV (rms), 50 Hz is supplying a half wave rectifier circuit. If the load resistance is 5 MΩ, find: a- The value of the smoothing capacitor so that the time constant is 10 times the supply periodical time. b- The rated peak inverse voltage (PIV) of the rectifier. c- The number of series connected rectifiers if the rated PIV of a rectifier is 20 kV. d- The ripple and the output voltages.
2.A single phase uncontrolled half wave rectifier has a transformer with a turns ratio of 5:1, has a source of 220Vrms at 60 Hz frequency, its supplies the load with a 100ohm resistance. Find: A. Average voltage and current and also in RMS B. Power and ripple factor
a half-wave rectifier circuit in the figure below has a transformer inserted between the source and the remainder of the circuit. The source is 240 Vrms at 60 Hz, and the load resistor is 20 ohm. (a) Determine the required transformer turns ratio (Ns/Np) so that the average load current is 12 A. (b) Determine the average current in the primary winding of the transformer.
i) Draw the circuit diagram of the single phase full wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation. (ii) A single phase fully controlled bridge rectifier circuit has DC output voltage 175 V for an AC supply voltage of 210 V rms. Find the firing angle delay of the circuit for the following cases (a) Converter mode (b) Inverter mode
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz, and is feeding a load 15 Ω and 10 mH. The firing angle α = 60˚ and the current extinction angle β =250˚; Determine (a) Average load voltage and current (b) RMS load voltage and current (c) AC and DC powers absorbed by the load (d) Determine the efficiency of the converter (e) Sketch the appropriate load voltage and load current waveforms (f) Determine whether the current is continuous or discontinuous