(i) A chopper circuit drives an inductive load from 360 DC supply. Given the load resistance as 8 2, the average load current as 20 A and operating frequency is 480 Hz. When the chopper is ON, 7 V is dropped. Calculate (a) conduction period (in milliseconds) (b) blocking period of the chopper (in milliseconds) (c) duty cycle of the chopper (d) draw the ON and OFF time period waveform (ii) Draw the circuit diagram of the single phase bridge rectifier which is used in two quadrant operation (RL load) and explain its operation. -

(i) A chopper circuit drives an inductive load from 360 DC supply. Given the load resistance as 8 2, the average load current as 20 A and operating frequency is 480 Hz. When the chopper is ON, 7 V is dropped. Calculate (a) conduction period (in milliseconds) (b) blocking period of the chopper (in milliseconds) (c) duty cycle of the chopper (d) draw the ON and OFF time period waveform (ii) Draw the circuit diagram of the single phase bridge rectifier which is used in two quadrant operation (RL load) and explain its operation. -

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
a) For the 2-Bus AC system given in Figure (a) find V1 (amplitude and angle). All the values are given in p.u. Note: Mind complex power concept! b) For the HVDC equivalent circuit given in Figure (b) calculate V2. All the values are given in p.u.
1- Derive expression for the output rms voltage for single phase ac voltage controller with resistive load
For type A chopper, dc source voltage = 250 V, load resistance = 10 Ω. Take a voltage excess of 2V across chopper when it is on. For a duty cycle of (0.004*Vs ), calculate (a) average and rms values of output voltage and (b) chopper efficiency.
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
A power plant comprises three turbine-generators rated 1000 MW, 800 MW and 600 MW respectively. The regulation constant of each generator is 0.05 pu based on its own rating. Each unit is initially operating at one-half of its own rating, when the system load suddenly increases by 250 MW. Calculate the following:a) Per-unit area frequency response characteristic on a 1000 MW system base [CR9]b) Steady-state drop in area frequency [CR4]c) The share of the load increase on each generator [CR9]d) Total load on each generator after the increase in system load [CR3]Assume the reference power setting of each turbine is unchanged.
Draw the circuit diagram of Two quadrant chopper which is having average load current might be positive or negative. Explain each quadrant operation with neat sketch
How does reactive power compensation improve the efficiency of power transmission?
Subject: Electrical & Electronics Engineering Course: Power Systems Question: What is GMR and GMD? Explain your answer in case of a composite conductor.
AA chopper circuit in the figure, 400 ? (???)Control the power of an ohmic load from a 50 ?? source.. Since the load resistance is 20 Ω and ? = 30 °,a) The effective voltage, current and power of the load,b) Input power factor,c) Apparent, active and reactive powers drawn from the network,d) Minimum blocking voltage of thyristor,e) Average value of each thyristor current,f) The required firing angle for the power transferred to the load to be 80% of the maximum power,calculate.
Name the component operating with ac power which best compares to the buck chopper.
Explain the concept of power factor correction and its significance in industrial power systems.