Helium expands polytropically through a turbine according to the process pv15=C. The inlet temperature is 1000 K, the inlet pressure is 1000 kPa, and the exit pressure is 150 kPa. The turbine produces 100 MW. Determine (a) the exit temperature, (b) the heat transferred, and (c) the mass flow rate. Ans: 531.3 K; Q= 16,646 kJ/s; m=34.25 kg/s

Q: 36mmø CISE NO. 1 (REACTIONS) 50deg C A Support 6m 4m 5 RA 12 1. Compute the stress in the support at...

A: Given: The value of force is W=107 kN. The diameter of wire is d=36 mm. Determine the equation for...

Q: Determine the maximum torque of the tube shown if the allowable shearing stress is 46 Mpa. Given: t ...

A: Given data:allowable shear stress = 46 MPat = 2.73 mma= 33 mm

Q: Calculate the discharge through the 140-mm diameter orifice shown. Assume C = 0.62.

A: Need to find the discharge through orifice.

Q: A 1-in steel shaft is loaded with combined bending and torsion: Ma = 1,024 lbf · in, Ta = 0 lbf · in...

A: diameter of shaft= 1 inch  Amplitude of moment= Ma= 1024 lbf Amplitude of bending stress = σa=(32Ma)...

Q: Define and describe general buckling. Enumerate and differentiate the different types of general buc...

A:

Q: 500 5. Calculate the resultant of the force system, and express it as a force and a couple moment wi...

A:

Q: What downward acceleration should be applied to a tank containing a certain liquid such that the pre...

A:    When dealing with the pressures exerted by gases and liquids, however, it is most convenient to a...

Q: A Consider the double pendulum shown in Fig. P4.61. The two point masses of equal mass m are attache...

A:

Q: How is the Eulerian description of fluid motion differ from the Lagrangian description? (select all ...

A: To study the motion of the fluid in fluid science, the various approaches used are: Eulerian approa...

Q: A block of wood is compressed 2.00 nm when inward forces of magnitude 132 N are applied to it on two...

A: Given Data: The magnitude of force applied, F=132 N Compression of the block, 2.00 nm

Q: Determine the time required for a car

A: Need to Determine the time

Q: Calculate velocity gradients and shear stress for y = 0.0, 0.2, 0.4, and 0.6 m, if the velocity prof...

A:

Q: Let A = (V+3)  feet per minute per minute. Find s and t when V = 12 fpm. Vo=0

A:

Q: 1) Find the equivalent spring, N/mm 2) Find the force, F Kl: K5 k K2 x=10 mm K3 K4 K6 ........ .....

A: GIVEN DATA - A SPRING SYSTEM GIVEN WE HAVE TO FIND EQUIVALENT SPRING STIFFNESS AND FORCE

Q: Newtons and x is the displacement in meters. Assume displacement data is known The force vs. displac...

A:

Q: Between 300K and 600K is the operating temperature of a pair of heat pumps connected in series. The ...

A:

Q: 500 lb./ft. 200 lb. 300 lb./ft. 150 lb./ft. 8 ft. 4 ft. 4 ft. 2 ft.

A:

Q: The basic barometer can be used to measure the height of a building. If the barometric readings at t...

A: Given  Pressure at the bottom, Pbot = 29.7 Hg        Pressure at the top, Ptop = 28.7 Hg            ...

Q: QI: An R-134a refrigeration system produces 10 ton of refrigerating effect at the evaporating temper...

A: The refrigeration cycle, also known as a heat pump cycle, is a method of directing heat away from th...

Q: An open tank, with bottom dimensions of 6 x 8 meters, is 6 meters high. It has oil with specific gra...

A: Given data: A=6×8 m2h=6 mSG=0.884a=5.55 m/s2 Need to determining the resulting force at the bottom o...

Q: [40] Problem 1: A bearing supports a 28mm diameter solid steel torsion rod (plan view shown in Fig. ...

A: Diameter = 28 mm Arm= 300 mm Vertical load =2500N To find. Total stress  

Q: A cycle HE does 60kJ of work per cycle. If the efficiency of the heat engine is 60%. The heat reject...

A:

Q: 6.17 A spacecraft is in a 300-km circular earth orbit. Calculate (a) The total delta-v required for ...

A:

Q: thrust bearing journal bearing D A _B E – 4 ft - 4 ft 4 ft → 4 ft --4 ft 'SN Ibs FN Ibs

A: To find: The internal loadings at point E: Internal axial force at E is, NE = ? Internal shear force...

Q: Determine the equivalent torsional spring constant of the system that will be located in the positio...

A:

Q: Locate the centroid (x, y) of the uniform wire bent in the shape shown 100 mm- 20 mm

A: a1=a2=a3=a4=a5=a x1=0x2=1002=50mmx3=50mmx4=50+502=75mx5=502=25mm x=a1x1+a2x2+a3x3+a4x4+a5x5a1+a2+a3...

Q: Compute for the forces in all members of the truss shown below using method of joints. -6 ft+6 ft+6 ...

A: GIVEN DATA - A PLANE TRUSS GIVEN WE HAVE TO FIND FORCES IN ALL MEMBER

Q: A steel bar of 30 mm * 30 mm square cross section is subjected to an axial compressive load of 300KN...

A: Given Data : Cross Section Area A = 30mm×30mm = 900 mm2 Compressive Load P = 300 KN = 300000 N Lengt...

Q: Consider a wheelbarrow carrying a load of 85 kg with its centre of mass as point G, as depicted in t...

A: As per the guidelines of BARTLEBY we are subjected to solve only one question at a time. Please repo...

Q: ow is the energy loss captured by the apparatus? "In Bernoulli’s Theorem"

A: the bernoulli's theorem is the law of conservation of energy for fluid. It states the sum of datum h...

Q: 3- For a power plant producing 10 MW of power using air-standard regenerative Brayton cycle operatin...

A: Given: The T-s diagram is as follows:

Q: A stepped 100 N-m as shown in figure below. Modulus of rigidity of material is 90 GPa, then angle of...

A: Given data: Torque, T=100 N-m G=90 GPa

Q: In a cycle, a 4kg ideal gas(MW=3g/mol and k=2.3) confined in a controlled mass system went through t...

A: For solution refer below images.

Q: 1. Air expands through a nozzle from 75 to 15 psia. The enthalpy decreases by 48 Btu/lbm the flow is...

A:

Q: Nitrogen at 100°C and 110 kPa with a volume of 1.8 m3 compressed using an isothermal process until t...

A: Answer: (a) The work done during this process is -255.615 kJ ( Negative sign indicates work input is...

Q: A heat pump has a coefficient of performance of 3.1 in heating mode. If it requires 130 J of work pe...

A:

Q: Calculate Stresses at (x.y.z) (0 in, 0.5 in, 0 in). You do NOT need to show Shear and Moment Diagram...

A: Find stresses at a point

Q: Steam enters a convergent-divergent nozzle at pressure of 22 bar and temperature of 300°C. the exit ...

A: From steam tables at pressure of 22 bar, saturation temperature is 217.24oC. As the temperature of s...

Q: The load is supported by the four 304 stainless steel wires that are connected to the rigid members ...

A: Given: P = 500 lb   To find: Angle of tilt of the members AB and DC.

Q: Heat exchanger is device that facilitate the exchange of heat between two fluids that are at differe...

A:

Q: Air contained within a piston–cylinder assembly undergoes three processes in series: Process 1–2: C...

A:

Q: A torsional bar is subjected to two external torques (10Nm and 5Nm) and a distributed torque (15Nm/m...

A: according to the details given above

Q: heat removal rate from the refrigerated space and the power input to the compressor are 9.0KW and 1....

A: Given:Qr=9.0 kWP=1.8 kW

Q: To draw the internal normal force diagram, it is important to determine the internal normal force at...

A:

Q: Which of the following statements are correct in the context of thermal conductivity? (Check all tha...

A: Thermal conductivity: It is a measure of heat flow through the material or it is a measure of how fa...

Q: 3. The 200-N force is the resultant R of the R 100-N-m couple moment and three forces, two of which ...

A:

Q: A solar energy based HE which recieves 60KJ of heat at 900C and rejects 50kJ of heat to the ambient ...

A: Given data,  Q1= 60 kJ ,T1= 90°C  Q2= 50 kJ ,T2= 30°C   

Q: . Dry air at 25 °C and 1 bar are to be liquefied. The air is isothermally compressed to 180 bar. Ass...

A:

Q: Need correct solution.  If C is the mid-point of PQ; What is the magnitude of bending moment at fi...

A: Given data  Given force system.

Q: 7. Calculate the resultant of the force and couple system shown. Express your answer as a single for...

A:

Laws of thermodynamics

Thermodynamics is a field of research, which needs the creation of absolute and ideal states and logical and practical examination of the actual conditions. By considering all the laws and theories of thermodynamics, the chemical reactions, the occurrence of processes, and physiological functions can be predicted with this field.