hich of the following statements is not true about the operation of an op-amp? In an op-amp, amplification of the opposite input signals is much greater than that of the common input signals. Op-amp's dlose loop operation employs negative feedback that takes portion of the output and applies it back ou input. Op-amp's close loop operation employs positive feedback that takes portion of the output and applies it back ou In open-loop operation, the output of the op-amp is driven to saturation with Vo = +Vsat.

hich of the following statements is not true about the operation of an op-amp? In an op-amp, amplification of the opposite input signals is much greater than that of the common input signals. Op-amp's dlose loop operation employs negative feedback that takes portion of the output and applies it back ou input. Op-amp's close loop operation employs positive feedback that takes portion of the output and applies it back ou In open-loop operation, the output of the op-amp is driven to saturation with Vo = +Vsat.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

A certain op-amp has three internal amplifier stages with midrange gains of 30 dB, 40 dB, and 20 dB. Each stage also has a critical frequency associated with it as follows: fc1 = 600 Hz, fc2 = 50 kHz, and fc3 = 200 kHz. (a) What is the midrange open-loop gain of the op-amp, expressed in dB? (b) What is the total phase shift through the amplifier, including inversion, when the signal frequency is 10 kHz?
A certain op-amp is used in a feedback configuration having a gain of 20 and a bandwidth of 500 kHz. a)If the external resistor values are changed to increase the gain to 40, what is the new bandwidth? The new bandwidth is 250khz What is the unity-gain bandwidth of the op-amp ??
Assume that the R2/R1 ratio of a feedback amplifier with voltage supply of +/- 10 V is 3.0 and that a value of 1.0 V is applied to the non inverting input of the op-amp. What is the output voltage value?
Assume that the R2/R1 ratio of a feedback amplifier with voltage supply of +/- 10 V is 3.4 and that a value of 8.5 V is applied to the inverting input of the op-amp. What is the output voltage value?
An amplifier has voltage gain with the feedback of 100. If the gain without feedback changes by 409 and the gain with feedback should not vary more than 8%, the values of open-loop gain and feedback ratio will be respectively given by
A gain of 10 is required from a noninverting constant-multiplier op-amp circuit. If the input resistor is 9 k Ω, what should be the value of the feedback resistor? Rf=_____kohms
If an opamp is perfroming by keeping two input voltages as 40 mV and 80 mv at inverting and non inverting amplifier respectivelyThen Calculate the output voltage for inverting amplifier with keeping input resistanceof 20 ohm and feedback resistance is 60 ohm.
Activity 2:You are asked to examine the performance of three op-amp circuits. 2-A) Categorize the circuits in terms of using a feedback or not, and the specific type of thefeedback connection (positive or negative, shunt or series, voltage or current).2-B) Explain the principle of operation of Circuit A. Explain limitations of this circuit in termsof practical applications. What is the technical name describing this circuit?2-C) Explain the principle of operation of Circuit B. What is the advantage of this circuitcompared to Circuit A? What is the technical name describing this circuit?2-D) Explain the principle of operation of Circuit C. What is the advantage of this circuitcompared to Circuits A and B? What is the technical name describing this circuit?2-E) Draw the block diagram of Circuit C and define the forward path gain A and feedbackpath gain β. Derive the overall circuit gain relating input to output.2-F) Build all circuits in MultisimTM using one ‘uA741CP‘op-amp IC fed by…
Q2/B)- Show the connection of three combination op-amp stages ( Parallel and series connection) using an LM348 IC to provide outputs that are 110, 400, and 2601 times larger than the input. Use a feedback resistor of Rf = 500 k? in all stages, while can use only (R= 50 k? for first stage), (R= 25 k? for second stage), and (R= 10 k? for third stage
An op-amp has an open-loop gain of 104 and a dominant open-loop pole at 4Hz. If an inverting amplifier with a gain of -100 is made from this op-amp, what is the resulting amplifier bandwidth? What is the gain-bandwidth product?
Please answer this two part question A) It is known that when an Op-amp is operated using the negative feedbackconfiguration, the output impedance reduces. Derive an expression that proves this. B) It is known that when an Op-amp is operated using the positive feedbackconfiguration, the output impedance increase. Derive an expression that proves this.
A certain op-amp is used in a feedback configuration having a gain of 20 and a bandwidth of 500 kHz. a)If the external resistor values are changed to increase the gain to 40, what is the new bandwidth? What is the unity-gain bandwidth of the op-amp in Question 34?