Problem 7-30:Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surfacetemperature of the 0.5-m-long flat plate is constant at 50°C. Determine (a) the local convection heattransfer coefficient at 0.2 m from the leading edge and the average convection heat transfercoefficient, and (b) repeat part (a) using the Churchill and Ozoe (1973) relation.Problem 7-76:In a geothermal power plant, the used geothermal water at 80°C enters a 15-cm-diameter and 400-m-long uninsulated pipe at a rate of 8.5 kg/s and leaves at 70°C before being reinjected back to theground. Windy air at 15°C flows normal to the pipe. Disregarding radiation, determine the averagewind velocity in km/h.Problem 7-112:Air is to be heated by passing it over a bank of 3-m-long tubes inside which steam is condensing at100°C. Air approaches the tube bank in the normal direction at 20°C and 1 atm with a mean velocityof 5.2 m/s. The outer diameter of the tubes is 1.6 cm, and the tubes are staggered with longitudinaland transverse pitches of S₂ = ST=4 cm. There are 20 rows in the flow direction with 10 tubes ineach row. Determine (a) the rate of heat transfer, (b) the pressure drop across the tube bank, and (c)the rate of condensation of steam inside the tubes. Evaluate the air properties at an assumed meantemperature of 35°C and 1 atm. Is this a good assumption?Problem 7-113:Repeat Prob. 7-112 for in-line arrangement with S,= ST = 6 cm.

Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surface temperature of the 0.5-m-long flat plate is constant at 50°C. Determine (a) the local convection heat transfer coefficient at 0.2 m from the leading edge and the average convection heat transfer coefficient, and (b) repeat part (a) using the Churchill and Ozoe (1973) relation.

Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surface temperature of the 0.5-m-long flat plate is constant at 50°C. Determine (a) the local convection heat transfer coefficient at 0.2 m from the leading edge and the average convection heat transfer coefficient, and (b) repeat part (a) using the Churchill and Ozoe (1973) relation.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.57P

See similar textbooks

Similar questions

Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
Airstream at 1 atm flows, with a velocity of 15 m/s, in parallel over a 3-m-long flat plate where there is an unheated starting length of 1 m. The airstream has a temperature of 20°C and the heated section of the flat plate is maintained at a constant temperature of 80°C. Determine (a) the local convection heat transfer coefficient at the trailing edge and (b) the average convection heat transfer coefficient for the heated section.
Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surface temperature of the 0.5-mlong flat plate is constant at 50°C. Determine (a) the local convection heat transfer coefficient at 0.2 m from the leading edge and the average convection heat transfer coefficient, and (b) repeat part (a) using the Churchill and Ozoe (1973) relation.
Air stream at 1 atm flows with a velocity of 2 m/s, in parallel over a 3 m long square flat plate, placed on ground, where there is an unheated starting length of 1 m. The air stream has a temperature of 20 °C and the heated section of the flat plate is maintained at a constant temperature of 80 °C. Determine the local heat transfer coefficient at trailing edge and average convection heat transfer coefficient for the heated section. Also calculate the heat loss by convection. Determine the average friction coefficient and wall shear stress and drag force.
Consider atmospheric air at 25?C and a velocity of 25 m/s flowing over both surfaces of a 1-m-long flat plate that is maintained at 125?C. Determine the rate of heat transfer per unit width from the plate for values of the critical Reynolds number corresponding to 5×105
The airflow at 1 atm has a free stream velocity and temperature of 5 cm/s and 25°C, respectively. Determine the heat flux on the plate surface and the convection heat transfer coefficient of the airflow.
A coated sheet is being dried with hot air blowing in cross flow on the sheet surface. The surface temperature of the sheet is constant at 90°C, while the air velocity and temperature are 0.3 m/s and 110°C, respectively. The length of the sheet subjected to the blowing hot air is 1 m long. Determine the convection heat transfer coefficient and the heat flux added to the sheet surface. Treat the coated sheet as a vertical plate in cross flow.
Please help with this questionHot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. Thegas at 220°C flow is parallel over the upper and lower surfaces of a 3-m-longflat plate at a velocity of 3 m/s. If the flat plate surface temperature ismaintained at 80°C.Determine the local convection heat transfer coefficient at 1 m fromthe leading edge and calculate the average convection heat transfer coefficient over theentire plate.
1.0 Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with velocity of 1 m/s: atmospheric air, water, engine oil, and mercury. For each fluid, determine the velocity and thermal boundary layer thicknesses, in mm, at a distance of 20 mm from the leading edge.
Air at 60°F flows over a 10-ft-long flat plate at 7 ft/s. Determine the local friction and heat transfer coefficients at intervals of 1 ft, and plot the results against the distance from the leading edge.
Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat plate where there is an unheated starting length of 5 cm. The heated section of the flat plate is maintained at a constant temperature of 50°C. Determine (a) the local convection heat transfer coefficient at the trailing edge, (b) the average convection heat transfer coefficient for the heated section, and (c) the rate of heat transfer per unit width for the heated section.
Water at 1500 kg/h and 10°C enters a 10-mmdiameter smooth tube whose wall temperature is maintained at 49°C. Calculate (a) the tube length necessary to heat the water to 40°C, and (b) the water outlet temperature if the tube length is doubled. Assume average water properties to be the same as in (a).