How does peak time, settling time, and percent overshoot relate with pole location of the underdamped system

Q: Define the followings: a) Hydrothermal scheduling problem? b) System blackout? c) Spinning reserve?

A: NOTE :- Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: Magnetic Tape Recording Explain briefly the mechanism of Magnetic Tape Recording and how is…

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Q: Generator 1 is committed to the bus bar. Specification says that it has to be in service for 120…

A: Choose the correct option Generator 1 is committed to the bus bar. Specification says that it has to…

Q: 7.Write down the safety issues related to Power Supply? а. b. c. d. 8. Write down the safety issues…

A:

Q: Ability of the power system to remain in synchronism after large disturbance is called as transient…

A: Transient and steady state stability are two important stabilities in power system.

Q: What is the Auto-re-closure scheme? Where this protective scheme is applied, and what are the key…

A: Each line circuit breaker is provided with an auto reclose relay that recloses the appropriate…

Q: Draw a simple block diagram of 'Open-Loop Control System' and 'Closed-Loop Control System' Not…

A: Note -  CS - control system

Q: Why six lamps are used in this dark lamp method of synchronization?

A:

Q: Explain briefly how will you give Combined Leakage and Overload Protection

A: Normally for leakage protection earth fault relay is used and for overload protection overload relay…

Q: Question 3: Interrelate the core saturation and different characteristics of over-current relay.…

A: Relation of core saturation and different characteristics of overcurrent relay is different for…

Q: Which of the following is not a type of energy requiring lockout or tagout procedures

A: Which of the following is not a type of energy requiring lockout or tagout procedure?

Q: What will happen when a generator suddenly fails while in operation a. System frequency will…

A: There are a lot of generators in the generating unit to meet the load requirements. If a generator…

Q: Classify whether Train door system (driverless train) is an open loop or closed loop control system.…

A: In driverless train the door opening system is always sensing the speed of the train.If the speed is…

Q: What are the different options to reject disturbances on a system? Comment briefly on feasibility of…

A: Disturbance rejection in process control  The unsettling influences could be outer or produced by…

Q: Give detailed information about Jury’s stability test.What are the conditions for Jury’s stability…

A: In signal processing and control theory,the jury stability test is the method of determining the…

Q: Give a real time example of an open loop system and explain with neat diagram the operation of it.…

A: an open-loop system is a type of control system in which the output of the system depends on the…

Q: 4. Why is less overshoot desired for practical systems?

A: Overshoot: It is the manifestation of a function or signal that exceeds its target.

Q: how the solder pot thermal overload unit operates during an overload situation?

A: we need to answer how the solder pot thermal overload unit operates during an overload situation.

Q: Describe the effect of the step size on the slope overload phenomena?

A: Slope overload phenomenon happens when the slope of the input signal is greater than the delta…

Q: What is a Bimetallic strip? Explain its function in Overload relay

A: The bimetallic strip is the device that work on the principle of thermal expansion. The thermal…

Q: For the Starting Up the Power Station Simulator Why are certain operations blocked by isolators

A:

Q: 1- What are the factors that affect the slope overload phenomena.

A: Since there are 5 questions, as per the guidelines, the first problem have been solved.

Q: What are the possible consequences of failure of the entire DC supply system in the station

A: It is known that at  the power generation unit ,DC supply system  is responsible for source of power…

Q: Earth system heated

A: The climate system is powered by rays from the sun, with about 49% absorbing the earth's surface,…

Q: Explain the difference between load and auxiliary contacts.

A: Auxiliary contacts are small. These are used as part of control circuit .

Q: Explain the reasons for applying system grounding in electric power systems.

A:

Q: What is the function of an arc chute

A: function of an arc chute

Q: Describe briefly circling the block diagram of fixed speed wind energy systems.

A: The short terms involved in the figure above are; SCIG :  Squirrel cage induction generator PCC :…

Q: How will you give Combined Leakage and Overload Protection?

A: It is a usual practice to provide combined leakage and overload protection for transformers. The…

Q: Determine whether the system is liner/non linear,time variant/time invariant,casual/anti…

A:

Q: Classify whether Train door system (driverless train) is an open-loop or closed-loop control system.…

A: Train door system in a driverless train is closed loop control system.

Q: Determine the closed loop poles for a 2nd order underdamped system knowing its settling time (2%…

A:

Q: Explain the following terms                                    a)     Operating Time b)     IDMT…

A: As per the guidelines, we are supposed to answer the first three-part of the question at a time so…

Q: What are words for being stable

A:

Q: Give a brief description for under/over voltage time relay.

A:

Q: What should be the K range for the system to be stable?

A:

Q: Q/ Do you observe any relation between the system damping ratio and the system settling time.

A: We need to tell about relationships between damping ratio and settling time

Q: Tp(peak time),Ts(settlign time),Tr(rise time),%OS(percent overshoot

A: The solution can be achieved as follows.

Q: hat is “Voltage collapse”? Why does voltage instability occur? What are the countermeasures to deal…

A: Voltage collapse is the process in which the voltage at significant part of the power system becomes…

Q: wing the locations of the system will be stable or r unstable? Why? 10s?

A: Since you have asked a multiple question we will solve the first question for you, If you want any…

Q: 25) How can eddy current loss be minimized?

A: Eddy current loss :- eddy current losses due to eddy current. Eddy current produced if any magnetic…

Q: When expansion fittings are installed in a run of metallic raceway, the electrical continuity and…

A: Bonding conductor or jumper is a reliable conductor that ensures the required electrical…

Q: Why six lamps are used in this dark lamp method of synchronization?

A: