How many compression ring and oil ring a IC engine piston will have? O a. 2 compression ring and 1 oil ring O b. 1compression ring and 2 oil ring O c. 2 compression ring and 2 oil ring O d. 1 compression ring ,1 oil ring and 1 pressure ring

Q: according to the C15 A.C.E.R.T caterpillar engine manual =, how is TDC 1o r 6 located

A: On a C-15 serial # 6NZ there is a threaded pipe plug on the front side of the flywheel…

Q: In a four-cylinder engine with a firing order of 1-3-4-2, what stroke is piston #4 on when #1 is on…

A: By the given firing order we can conclude that the 1st cylinder is 2 strokes ahead of 4th cylinder.…

Q: How many compression ring and oil ring a IC engine piston will have? a. 2 compression ring and 1…

A: Piston of internal combustion engine have three rings for each cylinder. Top two rings are called…

Q: A six-cylinder engine has a 1 5 3 6 2 4 firing order. Technician A says that after cylinder number 1…

A:

Q: 1-what are the parts of an engine? How are engine parts made? 2- Piston rings are used on the piston…

A: Solution:   Note; Dear Student! As per our guidelines, we are only allowed to answer three sub-parts…

Q: Master cylinder that is the terms used in

A: Brake  Pump

Q: Q2/ How will the following increase efficiency of the I.C. engine? 4. Movement of the piston to pass…

A: Given question: How will the following increase efficiency of the IC engine? 4. Movement of the…

Q: Explain with neat sketch of crank and lever mechanism used in oil and gas industry.

A: Crank and slotted lever mechanism:-

Q: e intake process wherein the pressure of the air entering the engine is increased by means of a…

A: The answer is given below:

Q: Which of the following are complexities that are ignored when assuming air-standard for an…

A: When combustion of fuel takes place within the closed heat engine, the heat produced due to…

Q: What happens to the engine due to high temperature ?

A: Engine: It is a mechanical device which is used to convert chemical energy of the fuel into…

Q: The diesel engines operates with low pressure than petrol engine

A: Correct option is:

Q: ne position of the piston when it is nea

A: 12) bottom 13)clearance

Q: How is the air exhausted at the back of the piston when the piston retracts?

A: By employing a single acting air cylinder in the application rather than a more traditional…

Q: Explain the working of two stroke petrol engine with a diagram

A:

Q: Which of the following best approximates pressure variations in an internal combustion engine?…

A: The cycle that best approximate pressure variation in an internal combustion engine is:-

Q: Write a note and explain about Modification of turbojet engine

A: TURBOJET ENGINE  A turbojet engine has all the power by expelling a high-energy gas stream from the…

Q: Which one of the following is a component of a centrifugal compressor? a. Suction valve b. Nozzle…

A: Although the centrifugal compressor is unlikely to be used in gas turbine plants where specific fuel…

Q: What is the method by which the pressure of the air entering the engine is raised using a compressor…

A:

Q: 1. Explain the difference between stoker, CFB, and PC from the three types of steam generators,…

A: CFB (Circulating Fluidised Bed) Boiler The circulating fluidized bed (CFB) is a developing…

Q: Why does BSFC decrease with load inthe engine?

A: Conversion efficiency of the fuel is the main reason for the reduction in BSFC with load. At higher…

Q: 1. Explain with neat sketch of crank and lever mechanism used in oil and gas industry.

A:

Q: The piston top surface is generally flat in the indirect injection  True False

A: Given: The piston top surface is generally flat in the indirect injection

Q: How many degrees the crankshaft will rotate with both the intake and exhaust valves seated when the…

A: Calculate the degrees for which the crankshaft rotates with the intake and exhaust valve seated.…

Q: too lean mixture is supplied to the engine and may be caused in:

A:

Q: umerate the advantages and disadvantages of the following types of engine: a.) Rotary or Wankle…

A: C) Rotary Engine Advantages 1.it has higher power to weight ratio. 2. it has no reciprocating…

Q: Briefly explain a 2 and 4 stroke Engines and how each operation.

A: Engines are classified based on the number of strokes as 2 stroke engine and 4 stroke engines. In 2…

Q: Number of explosions of piston on a single cylinder, four stroke cycle engine in 100 revolutions of…

A: Given data To determine the number of explosions of piston on a single cylinder, four stroke cycle.

Q: The bolt size of cylinder head in a reciprocating compressor is a. M16

A: The bold size of the cylinder head in a reciprocating engine M16 option (a) is correct.

Q: The bolt size of cylinder head in a reciprocating compressor is _____ a. M20 b. M16 c. M24…

A: As it has a trend to fatigue failure in Reciprocating Compressor... So, we need higher sized bolt...

Q: al cup of equired to pach job f 240 cc ecificatio

A: Given: The radius of hemispherical cup is 15cm The force required to deform is 8KN. The approach…

Q: Where should the temperature difference be the greatest to make the Sirling engine operate well? O…

A: A Stirling engine operates by the expansion and compression of a working fluid (Mostly gas) and so…

Q: What would happen if one of the Flow Controls were reversed in a cylinder?  What are the…

A: Consider the cylinder as an open system. To implement the flow controls, consider the control volume…

Q: INTRODUCTION ABOUT VALVE SYSTEM IN INTERNAL COMBUSTION ENGINE

A: In this solution we will only discuss about the brief introduction about the valve mechanism in the…

Q: Why does a free-to-move piston hold a constant pressure in the cylinder?

A: Free-to-move piston is the one in which the friction is zero and the atmospheric pressure outside…

Q: The 4 basic classifications of engine gaskets are?

A: Determine the 4 types of engine gasket as given below. (a) Cylinder head gasket - Copper and…

Q: The function of carburettor used in engine is to O a. mix air, petrol and diesel in engines b. mix…

A:

Q: What part is often changed with a water pump? Select one: a. A crankshaft pulley b. A timing belt

A: Generally, the idler pulleys, tensioner and water pump ought to continuously be replaced when the…

Q: The diesel engines operates with low pressure than petrol engine O a TRUE Ob. FALSE

A: The diesel engine operates on a diesel cycle while the petrol engine operates on an otto cycle. The…

Q: Diesel engine fuel is rated by?

A: It is required to rate the diesel fuel

Q: List out the design requirements of diesel engine combustion chamber

A: Diesel engines work on the diesel cycle. In diesel engines, the air is compressed alone and at the…

Q: Write short note on engine capacity

A: The engine capacity is one of the important specification in IC engine.

Q: What is definition of natural gas compressor?

A: Natural Gas Compressor: Generally compressor used for increasing the pressure and temperature of the…

Q: argue briefiy thất thế heat capacity at constant pressure is capacity at constant volume for a gas…

A: Thermodynamics: It is a branch of science which deals with work , heat , energy.  Also it studies…

Q: P -P -8 in. -8 in.- (a) (b) /hich of the following best explains why cylinder (b) har a binh

A: Given: Which of the following best explains why cylinder (b) has higher longitudinal stress in its…

Q: nal combustion engine that ion and operation. Due to

A: Assume 1 kg of working subsance Process 1 -2 : Isentropic process  Process 2-3 : Heat supply at…

Q: Discuss the differences of diesel and gasoline engine.

A:

Q: Why diesel engine doesn’t have spark plug?

A: spark plugs is used to ignites the air/fuel mixture for creating the explosion inside the piston…