What part is often changed with a water pump? Select one: a. A crankshaft pulley b. A timing belt

Q: name two advantages and two disadvantages that air has in comparison to oil when used in a fluid…

A: To write: The advantages and disadvantages of air over oil in a fluid power system. Explanation:…

Q: In Lin the center position port A and B are connected to tank port and pump port is blocked.

A: Hydraulics is a part in which the fluid power is used for various applications. The fluid pressures…

Q: Derive an espression for the height of propell governor

A: Deriving expression for proell governor considering proell governor taking moment about point…

Q: advantages and 5 disadvantages of using trash pumpp

A:

Q: What happens if the delivery valveof a running reciprocating pump is closed?

A:

Q: Explain the job of Rudder

A: The rudder is a primary flight control surface that controls rotation about the vertical axis of an…

Q: Multicylinder pump

A: Where more than one cylinder is being driven by one driver, the arrangement is named according to…

Q: ed between two large open reservo ne elevation When the pump adds

A:

Q: Explain what happens at each stage of the machine's cycle

A: A machine cycle is consist of four steps. These steps are fetch, decode, execute and store. The…

Q: 04: Complete the secetion of the reciprocating pump (shown in figure.2) by adding the details of the…

A: Gear box in the reciprocating pump The purpose of the gearbox is to convent rotating energy to…

Q: C- Mention three of the advantage of the positive displacement pump?

A: The question given is

Q: Name two ways of regulating flow to a hydraulic actuator.

A: There are many ways to control or regulate flow in hydraulic systems. There are many simple and…

Q: By the analysis of figure 1 above, compare the speed of the extend and retract of the hydraulic…

A: From the analysis of the given figure

Q: Which type of the pump is different from others in the same group? Select one: a. Piston pump O b.…

A: We have to find  Which type of the pump is different from others in the same group ?

Q: A single cylinder engine is used to drive an irrigation pump. The set-up has the following data:…

A: The diameter of the pump pulley: 305.5556 mm

Q: ". Compressor blades are twisted from root to tip:

A: Compressor blades are twisted from root to tip

Q: A- List three differences between the dynamic pump and peristaltic pump?

A: Given question: List three differences between the dynamic pump and peristaltic pump.

Q: With a neat sketch explain the Analysis of simple hydraulic Jack.

A: Jacks are pieces of industrial heavy equipment that raise or move heavy loads by multiplying force.…

Q: Which of the following situations will make a pump noisy? Select all that apply. O Excessive oil…

A: Answer:- All given situations will make the pump noisy.   The various situation that will make the…

Q: What areas within a vane pump or motor are the most susceptible to contamination-induced clearance…

A: Vane Pump :  A vane pump is a type of positive displacement pump that delivers a constant flow rate…

Q: Draw the symbol of pressure relief valve and briefly describe about use of the pump and motor?

A: The symbol of simple pressure relief valve is shown below:

Q: * write the advantages and disadvantages of Axial piston pump ? * Describe about use of pressure…

A: Axial Piston pump are also called reciprocating pumps and pressure build is up to 14,000 psi.…

Q: 2- A gear pump with a rotational

A: Gear Pump: A gear pump pumps fluid through displacement, and it does so by the meshing of gears.…

Q: C- Mention three of the advantage of the positive displacement 4 pump?

A: Given Data- Positive diaplacement pump given we have to list out its three advantage

Q: Draw a neat diagram and explain in detail about any one type of rotary compressor.

A: "Rotary Vane compressor" is one kind of rotary compressor. It  has sliding vanes  which are fit over…

Q: A- Briefly compare between actual and theoretical valves timing with drawing.

A: Theoretical valve timing diagram:  In theoretical valve timing diagram suction and exhaust valve…

Q: Name possible applications for 4/2-way hand lever valves.

A: Spool valve: Spool valve are the usual choice for directional control, because they can be…

Q: a hydraulic tu the full scale of the full scal

A:

Q: In pneumatic actuators, fluid is used instead of compressed gas as in hydraulic actuators. True or…

A: In pneumatic actuators , compressed gases are used to transfer power . In hydraulic incompressible…

Q: Identify the Pump which increase the pressure due to squeezing action and explain its working…

A: The pumps which is used to increase the pressure by squeezing action is gear pump or rotary pump.…

Q: (b) Describe the difference between: i. Reciprocating pump and Centrifugal pump ii. NPSHA and NPSHR

A:

Q: What are the reasons for a noisy aircraft engine driven hydraulic pump and how to troubleshoot it

A:

Q: The engine shown in the picture may be called

A: The engine shown in the picture may ...................... be called. Answer: 8-cylinder V-engine

Q: 5) What are the main components of a function of each part? centrifugal pump and what is the

A:

Q: An oil leak at the bellows of a rack and pinion could be caused by ______.

A: As per given question  What is the cause of Oli leak at bellows of a rack and pinion

Q: Name the following directional control valve: 4 1 O a.5/2 way double solenoid valve with bypass…

A: Given : To find: Name the valve

Q: 2- Draw theoretical valve timing diagram and compare it with actual one.

A:

Q: Explain what is meant by a hydraulically balanced vane pump. How is this accom- plished?

A: INTRODUCTION : A vane pump is a positive displacement pump which is use to maintains a constant flow…

Q: verno

A: governor: In technology, a governor is a mechanism that keeps the rotational speed of an engine or…

Q: Choose the symbol for Fixed displacement single rotation compressor. Select one: O a. O b. Oc. d.

A: option a is only for fixed displacement compressor  option b is double rotation direction variable…

Q: Explain the working principle of the lobe pump with the help of neat sketches?

A:

Q: The 3 basic oil seal designs to keep fluids from escaping around a rotating shaft are?

A: The three basic oil seal design to keep fluid from escaping around a rotating shaft are-

Q: The inside of a hydraulic power unit is shown. Identify pats A,C, and E

A: Solution: Given Data:

Q: Which type of the pump is different from others in the same group? Select one: a. Plunger pump b.…

A: Answer:-  Option (a) correct. Plunger pump.

Q: tate the operation principle of pressure-limiting variable vane pump according to the following…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.