How to calculate error % in viscosity?

Q: What is the relationship between sensitivity and radius?

A: The change in angle or gradient of the level that results in movement of the bubble is known as…

Q: 6. How can we write kinematic viscosity using the MLT system? a) [M][L][T]? b) [M]°[L]?[T]1 c)…

A:

Q: What exactly is a particle size analyzer, and how does it work?

A: Introduction: The analyzer of particle size A particle size analyzer is used to ascertain the size…

Q: Explain the Thickness of Layers.

A: Earth layer thickness:

Q: What is a secant Modulus?

A: Secant modulus:

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: Calculate the following: xbar (location of the centroid along x axis), mm ybar (location of the…

A:

Q: Define vibration

A: Vibration has been defined in the following step.

Q: Explain the benefits of using computer software in structural analysis and design.

A:

Q: computer aided engineering

A: Computer-aided engineering (CAE) is the use of computer software to simulate performance in order to…

Q: Answer the problem with complete solution and box the final answer with 4 significant figure and…

A: Solution:-

Q: Which of the followings does not help to produce good-quality technical sketches and drawings? a)…

A: Eraser: if we are using the eraser more frequently then the quality of drawing will decrease. Pens:…

Q: Describe the Particle Shapes and Sizes.

A: Particle size refers to the dimensions of particles (solid, liquid and gaseous. It is used for…

Q: What should be the name of the layer shown as " purple ?" As a numerical calculation, the fault line…

A: We will solve this question in step no. 2

Q: 6. How can we write kinematic viscosity using the MLT system? a) [M][L][T]? b) [M]°[L]?[T]*1 c)…

A:

Q: For the shape below, calculate: y a COLLAPSE IMAGES a = 80 cm b = 80 cm C = 110 cm

A: For bigger Rectangle : Area (A1)=c×2×a=110×2×80=17600 cm2X1¯=-c2=-1102=-55 cmY1¯=2×a2=2×802=80 cm…

Q: HYDROMETEOROLOGY Discuss how a Unit Hydrograph is used. And provide an example of how it is…

A:

Q: viscosity, vo VISCOSIT

A: S0 = 0.85 Density of oil = 0.85 x density of water Density of oil = 0.85 x 1000 = 850 kg/m3 Dynamic…

Q: Differentiate initial and boundary value problems.

A: Both type of problems are similar to each other except for that boundary value problem have…

Q: Find the area of the object below. Round to the nearest unit. SHOW YOUR WORK IN THE ANSWER BOX BELOW…

A: We will divide the whole area into 4 different parts.

Q: SIEVE ANALY SIS - US STANDARD SIEVE SIZES BIEVE NUMBER. HYDROMET 30 60 30 140 114 18 10 20 40 80 100…

A: given  LL = 34PL = 22IP = LL -PL ⇒12A - line = 0.7322-20               = 10.22

Q: the box. What is the probability ?that both marbles are red

A: Solution: Given that, No of yellow marbles = 3 No of red marbles = 2 No of green marbles = 4 No of…

Q: 32. Which of the following is the mathematical technique used to predict physical parameters? a)…

A: Physical values are described in terms of the structural dimensions when doing a dimensional…

Q: What sieve size has the lowest percent passing? (2 decimal places, no need for unit) Blank 1 Blank 1…

A:

Q: How is Ic = 0.3682 calculated through ratio and proportion? Show complete solution and neat…

A: to find - value of Ic based on graph . for further queries about question please upload full…

Q: Before taking measurements, someone usually calibrates the measuring instrument. Describe your…

A: Calibration is the comparison of measurement results provided by a system under test with a…

Q: Please include complete solution and diagram if possible.

A:

Q: What is a boundary value problem? Where did it occur?

A:

Q: Draw the following for the following figure (complete front section / horizontăl projęctión / side…

A:

Q: Draw a line segment 6 inches long. Subdivide it according to the golden ratio.

A: The length of the line segment is 6 inches. Let the length of the longer side be x and the length of…

Q: plete solution with clear calculations , don't miss anything.

A:

Q: Common problems in road construction

A:

Q: What are the common sources of error associated with measurements

A: to find  common sources of error associated with measurements

Q: What are the problems associated in primer designing?  Please answer at your own words.

A: Without primers, PCR machines become more sophisticated. Primers are more common than the final…

Q: would it be possible to show the line measurements in feet? autocad

A: Yes it is possible.

Q: Given the composite figure, 80 mm 30 mm 60 mm 90 mm 30 mm 20 mm The y-coordinate of the centroid…

A:

Q: x 6m deformed bars? t the correct response: 465 471 461 468

A:

Q: How to get TEC and TBC

A: Given data  0.77TEC + 0.8TBD = 1440...........(1) 0.514TEC - 1.6 TBD = 0...............(2)

Q: Enumerate the glasswares used in accurate volume measurements.

A: Solution:- The Graduated cylinders, beakers, volumetric pipets, burets and volumetric flasks are…

Q: 60 mm 60 mm

A: To find the centroid -

Q: Approximation, projection pr prediction of a quantity of work; a statement of the approximate or…

A: Brief concept introduction- The successful execution of the project needs proper planning,…

Q: What sieve size has the lowest percent passing? (2 decimal places, no need for unit

A: Percent passing decreases as we move down the sieve ( smallest sieve at bottom). Since smaller sieve…

Errors in surveying

An error in surveying is defined as the difference between two or more values of an identical quantity. However, the estimates are never accurate and there will always be a degree of variability regardless of the research tool or method used. These differences are known as errors that need to be reduced or eliminated to maintain certain levels of accuracy. Even if you carefully follow the prescribed test procedures, the considerations may contain errors.