Kindly do it as soon as possible I'll rate Two large reservoirs containing water ot 20°C are connected by a pipe, 9.7 m in length and 3 mgm in diometer, mode of galvanized iron. The elevationdifference of two tree surfaces in the reservoirs is 0.55 m. Neglecting any minor lonses, determine the flow rate through the pipe in Im/sl The tolerance ofyour answer is 2%

Two large reservoirs containing water at 20°C are connected by a pipo, 9.7 m in longth and 3 mm in…

Two large reservoirs contoining water ot 20C ore connected by a pipe, 9.7 m in length ond 3 mom in diometer, mode of golvanized iron The elevation difference of two free surtaces in the reservoirs is 0.55 m. Neglecting any minor losses, determine the flow rote through the pipe in (m/s) The tolerance of your onswer is 2%

Two large reservoirs contoining water ot 20C ore connected by a pipe, 9.7 m in length ond 3 mom in diometer, mode of golvanized iron The elevation difference of two free surtaces in the reservoirs is 0.55 m. Neglecting any minor losses, determine the flow rote through the pipe in (m/s) The tolerance of your onswer is 2%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rate of flow of water through a cylindrical tube that has an inner radius of 1.2 cm is 2791 cm3 in 88s at 293 K. Determine if the flow laminar or turbulent.
The volume flow rate of laminar and fully developed flow in an inclined pipe of length L can be calculated using the formula of Q=[(ΔP-ρgLsinθ)πD⁴]/128μL. When this pipe is placed on the horizontal plane under the same condition, which term of the above expression should be eliminated?
Water at 10 C flows in a 1.25-cm-diameter pipe at a rate of 1.33 L/min. The hydrodynamic entry length (in meters) is
A small centrifugal pump is used to pump 30-Celsius water at the rate of 6 L/s with ahead of 44.54 m. If the diameter of the pump is 20 cm and operate at 1200 rpm,determine;(i) head coefficient,(ii) capacity coefficient, and(iii) power coefficient. also the same small centrifugal pump is used to pump water at same rate but with a temperature of 15-Celsius. determine in which condition (15-Cor 30-C) is the pump perform better in term of;(i) power out, and(ii) pump efficiency.Justify your answer.
Water at 10 C flows in a 3.5-cm-diameter pipe at a velocity of 1.75 m/s. The Reynolds number for this flow is ?
Glycerin at 40°C with r = 1252 kg/m3 and m = 0.27 kg/m·s is flowing through a 4-cm-diameter horizontal smooth pipe with an average velocity of 3.5 m/s. Determine the pressure drop per 10 m of the pipe.
[CE Hydraulics] 5. For the case of turbulent flow in rough pipes, does the friction factor depend on the Reynolds number? Why?
A horizontal concrete pipe (material roughness = 1.3 mm) with diameter of 5 cm andlength of 300 m is used to transport acetic acid. The density and dynamic viscosity ofthe acetic acid is 1049 kg/m3and 0.001155 Pa.s. If the flow rate required for thetransportation is 30 litre per minute: Determine the required pump power to overcome the head loss using Moody chartand Colebrook-White equation; Determine the required pump power to overcome the head loss using Altshul’scorrelation as shown in the equation below; Compare the difference of pumping power between answers obtained in Q5(a) andQ5(b) and discuss the validity/accuracy for Altshul’s correlation.
Consider a flow of SAE 30W oil at 20°C through a 2.4-cm-diameter smooth pipe at 1 million N/h. Determine the Reynolds number for this flow. For SAE 30W oil at 20°C, take ρ = 891 kg/m3, μ = 0.29 kg/m-s, and π = 22/7. The Reynolds number is
A vertical channel of diameter 5 cm and length 10 m is conducting water in upward manner( water viscosity= 1x10 -6 m2/s , water density =1000 kg/m3 ). For the presence of laminar flow regime determine the maximum amount of flow rate approximately ( Use pi number as 3,14 )ANSWER: 0,09 kg/s
plzzzz help me with this one plzzz Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m3 ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate of 0.2 m3/s. If the pipe is cast iron of diameter 12 cm and the pump efficient is =0.44%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss.
Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe lengthis 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should bethe different in elevation between the upper and lower levels in order to achieve this pressure? Takethe density of water 1000 kg/m3 and gravity is 9.81 m/s2, consider the energy loss.