HW Problem Determine the components of F1 and F2 in x-y and x'-y' systems F1 = 500 lb %3D 25° 45° 30° F2= 750 lb

Q: Determine the loads acting on the frame at A, D, and E. Treat each connection as a ball and socket…

A:

Q: Draw the free-body diagram of CBA and DB

A:

Q: The lift is holding a 190 lb welght as shown. Calculate the reaction force components reaction…

A:

Q: 2) Find the true magnitude and direction of the forces in all the members of the truss AB AND AC at…

A: Solution:

Q: Answer with proper explanations.

A: The free body diagram for the lighter block is given below,   The force equilibrium in y-direction,…

Q: C PROBLEM 10 25 12 Determine the tension in cable AC if the traffic light has a mass of 12 kg. A)…

A:

Q: (A) What is the work done by the spring force (– Fx). (B) how many degrees of freedom has the spring…

A: Work done by the spring force is defined as the dot product of the restoring force exerted by the…

Q: 13.] Thirteen spring balances are attached to the center ring of the force table. The following list…

A: For all the forces, consider below coordinate system, where positive x axis is along east and…

Q: Problem (3) Determine the horizontal and vertical components of reaction at pin C. 400 N -2 m 800N -…

A: Given structure:

Q: 2 m H. 4 m E B a -4 m - 4 m 4 m 4 m 5 kN 3 kN (a)

A: Given:-  To Find:-  Forces in each members Solution:-  Firstly find out the support reactions using…

Q: 4)Find true magnitude and direction of forces on the wheel and cable members at static…

A:

Q: Draw free-body diagrams of members AC and BG 3 m -8 m G 2 m 15 2 m 8 2 m A 300 N 3**3**3*

A:

Q: What is the force resisted by member EF? C D B 6 m 4 m 4 m E A 6 m 6 m G 6 m F 6 m

A: Concept of engineering mechanics used

Q: Fig. Q3 c E KN in c maximo at joint C

A:

Q: Part A When y is zero, the springs sustain a force of 54 lb. (Figure 1) Determine the magnitude of…

A:

Q: 3. The arm of the excavator can be approximated with weights W1 and W2 located at their indicated…

A:

Q: Develop a free body diagram based on the structure. There must be a system FBD and an FBD of one…

A:

Q: Draw Free Body Diagram for two *pulleys W = 200 kN W = 400 kN 1m 2 m B 5.6 m

A:

Q: Drill pipes of 1000 meter original length which is between top drive drilling motor and bottom hole…

A: Given :-  OD-200 mm, ID=175 mm, E = 50 GPa, G=77.2 GPa weight: drill pipe = 100,000 N, bottom hole…

Q: Determine the N.F. of the D.O.F. Springs - Mass Systems as shown in Figures below? k M1 k M2 X2 k M3…

A:

Q: The beam as shown, has negligible weight. If the system hangs in equilibrium when FWi 500.0N, what…

A:

Q: View Policies Current Attempt in Progress Determine the magnitude of the pin force at A. Assume W =…

A: To find : The magnitude of pin force at A . Given data : The Weight is W=565 lb. The values are…

Q: The horizontal reaction at support O will be at the 100 lb 1 ft 50 lb 3 ft 3 ft 3. 4 150 lb O non of…

A: Option 4th is correct. (In the positive direction)

Q: For the frame shown below draw the influence lines for Ey, Fy, VC and MC using the equilibrium…

A: Given dataLA=4mLB=3m

Q: 30° а ст 2r Figure 3 D Č, 4) There are three cylinders located as in the figure 4. Two of them which…

A: The free-body diagram of the system is given below, The value of angle θ, θ=cos-1r3r=70.528o

Q: Arm ABC is connected by pins to a collar at Band to crank CD at C. Neglect the effect of friction.…

A: From the given diagram the point C is a hinge, so it has a horizontal and a vertical reaction, B is…

Q: bearings at A and D exert only vertical reaction on the shaft. The loading is applied to the pulleys…

A:

Q: Determine the magnitude of the pin reactions at Band Cif W = 1720 Ib. 3.7' 3.7' BI 2.0' Answers: B =…

A:

Q: Analyze the given cable and determine the maximum tension that will occur in DE 6m D. 20KN 1.5m 30KN…

A:

Q: Question 4 ZA し2m cable 3m cabile cable -strut Char) Werght W= 80N

A: Write the coordinates of the point:- A≡0,0,0B≡-3,-2,8C≡-3,2,8D≡-3,0,0 Write the vector co-ordinate…

Q: Drill pipes of 1000 meter original length which is between top drive drilling motor and bottom hole…

A: Given :-  OD-200 mm, ID=175 mm, E = 50 GPa, G=77.2 GPa weight: drill pipe = 100,000 N, bottom hole…

Q: The 100 kg cylinder is suspended from the ceiling by cables attached at points B, C and D. Calculate…

A: ∑F=TAB+TAC+TAD-9.81=0rBA=(xB-xA)1 +0~(yB-yA)j^ + (zB-zA)k^    = (4i°+4j+zk^)m°r^BA= rBArBA=…

Q: The load D has a mass of 410 kg and is being hoisted by the motor M with constant velocity. (Figure…

A:

Q: Drill pipes of 1000 meter original length which is between top drive drilling motor and bottom hole…

A: Given :-  OD=200 mm, ID-175 mm, E = 50 GPa, G = 77.2 GPa weight: drill pipe = 100,000 N, bottom hole…

Q: Q 10/Determine the force in member CK of the loaded truss. 1.5m 15m H 1m -3m M IN /1.5m 1.5m G 2.25…

A:

Q: 8 pulg 8 pulg 18 pulg 48 pulg 106 pulg -8 pulg E 5000 lb

A: Given : The weight lifted by crane = 5000 lb Solution : A 5000 lb load is lifted by the crane with…

Q: PROBLEM 1 P1, P2 = 30 kips %3D Determine the internal force in the ff. members: [ Select] 1. DG (…

A:

Q: he _____ of a pressure regulator houses mechanical components a. body b. piston c. popp

A: Given: Pressure regulator houses

Q: Based on the diagram below, what is the force in Cable B so that the traffic signal is in static…

A: Given, W = 74 lb FA = 280 lb   Consider below FBD:

Q: E2 ft+l ft IC |B D 100 lb/ft 3 ft 4 ft

A: A free body diagram is a diagrammatic representation of all the forces acting on the system…

Q: Which of the following is a zero-force member

A: A zero-force member is a member in the truss in which neither tension nor compression is present.

Q: 8 pulg; 8 pulg 18 pulg D 106 pulg -8 pulg - 48 pulg E 5000 lb

A: The weight lifted by crane = 5000 lb Solution : Consider the free body diagram of the crane as shown…

Q: To test the deflection on a uniform 100-kg beam, a boy of who weighs 50 kg exerts a pull of 150N on…

A: Equilibrium of rigid bodies in equilibrium refers to when both the resultant force and the resultant…

Q: • Exercise: Obtain the equivalent stiffness for the following spring networks. kl xl i) Wwww x2 Www…

A:

Q: PROBLEM 8.3 Hg = 0.30 Hx = 0.20 250 lb Determine whether the block shown is in equilibrium and find…

A:

Q: 6. If the 2.30 kg uniform beam shown in static equilibrium, what is the magnitude of F, ? 30 0° 5.00…

A: Given: Mass of the beam (m)=2.3kg

Q: Determine the S.F. component sustained by the web of ISLB 450 ( b f= 170.0 mm , tf = 13.4 mm ,tw =…

A:

Q: YA A В L, =162 (57° L = 77 L, = 73 3. 027 X

A: given:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.