HW04-1 F = 600 lb; 120° %3D Determine the magnitude and the direction of the resultant force act- ing on the pipe assembly. 60° F= 400 lb %3D
Q: The following are stress and strain tensors at any point. Determine the principal stresses or…
A: Given Data⇒ Problem definition⇒ Problem says Determine the principalstresses or strains and the…
Q: Determine the x and y components of reaction at the pin A. Express your answers using three…
A: As for guideline we can slove one question here we have to find reaction of beam
Q: Find the resultant force of the following? 2 m F- 600 N 3.5 m 0.5 m F 450 N 1.5 m 1m 1.5m 0.5 m y
A:
Q: Q 2. In the frg. shown below. Resolve the force lo0lb into taio Components one abng AB and the other…
A:
Q: Q1 show thot the force F-ljz-6xZ)+(2xyz) J+ (3xyz-6²z)is cors ervative, hence find i the Patenial…
A: Given: F=(y2z3-6xz2)i+(2xyz3)j+(3xy2z2-6x2z)k
Q: Q2/ The cable BC carries a tension of 750 N. Write this tension as a force T acting on point B in…
A:
Q: "The reaction at A is * 40N 200 mm В 300 mm 20N 300mm 45°
A: Let FBX and FBY are the horizontal and the vertical reactions at the hinge support B respectively.…
Q: Q2/ The cable BC carries a tension of 750 N. Write this tension as a force T acting on point B in…
A:
Q: 4.500 m 2. The pipe assembly is subjected to 500 kg of load. Determine the ff; a. Draw the FBD…
A:
Q: Q/ Use the conditions of equilibrium to solve the following problem and find the magnitude of the…
A: for the given system of forces To determine The magnitude of the resultant force and its…
Q: P4-4. Determine the friction force at the surface of contact. 500 N W = 200 N H = 02
A:
Q: 1- The work done by the force F 41-31+2 k to displace a body from point (3,2,-1) to point (2,-1,4)…
A:
Q: Q3/ By using the cosines law, if ( a = 40.9 %3D :)the force R equalS to 800 N P. a R 600 N Va T
A: To determine the resultant R using cosine law
Q: The pipe assembly is supported by smooth journal bearings at A. B. and C. Suppose that F = 310 N.…
A: F = 310 N Answer Ay , AZ = 0 N , 620 N Bx , BZ = 0 N , -1240 N CY , Cz = 0 N, 930 N
Q: u=7i-9j, w=-i-6j find w-u
A:
Q: 35 ft HW05-2 The cable attached to the shear-leg derrick exerts a force on the derrick of F = 350…
A:
Q: Determine the algebraic sum of the moments of forces relative to a point in F = 10.0 N; m =9.0 Nm, q…
A:
Q: Q/ Use the conditions of equilibrium to solve the following problem and find the magnitude of the…
A:
Q: 2. Which of the following equilibrium equations correctly relates the tension forces TDA and TDB…
A:
Q: Find the resultant force of the following? B, F-600 N 3.5 m 0.5 m F- 450 N 1.5 m 1m 1.5 m 0.5 m y X…
A:
Q: Q = 500 N T= 300 N 20° F- 600 N 30° P= 400 N
A: Determine angle made by force Q (500N) with X axis (Note- X axis is not horizontal it is inclined at…
Q: Determine the magnitude and location of the equivalent resultant force acting on the shaft in Fig.…
A:
Q: 600 lb 25t 25 ft OD 25 t 25t 1. The structure is: 2. The two-force member is: AB and CD v and its 3.…
A:
Q: Engineering Mechanics Statics (Equilibrium of a Particle) Ayad A. M. Q/ Use the conditions of…
A:
Q: Q3) Determine the maximum and minimum tensions if w. 8 kg /m as shown in fig. below? 50 m h-Sm…
A: Given: L = 50m h =5m w0 = 8 kg/m q =w0*g = 80 N/m Tension at support 1 is R1 and tension at support…
Q: For the crane system, determine the hydraulic cylinder force required to lift a 3500 N load O21349 N…
A: To Find The hydraulic cylinder force required to lift. FBD: The free body diagram.
Q: G2 0.3 r
A:
Q: The pressure loading on the plate varies uniformly along each of its edges. Determine the magnitude…
A: Given data: p=ax+by+c Need to determine the value of "c".
Q: 4 m + 4 m 150 KN 6m. 25 kN/m 10 m B
A: Draw the free-body diagram of the beam. Apply moment equilibrium about point A.…
Q: P14-1. Determine the work of the force when it displaces 2 m. 500 N - 2 m- (a) 98.1 N 2 m- (b) 2 m…
A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…
Q: Compute the work done by the indicated force when the disk undergoes the specified displacement…
A:
Q: Q.3) The force applied to a rigid body can: (a) not be translated along its line of action (b) not…
A: Since force is a first rank tensor, that requires not only magnitude but direction also. The force…
Q: P14-1. Determine the work of the force when it displaces 2 m. k = 10 N/m 2 m 500 N Spring is…
A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…
Q: The cable BC carries a tension of 750 N. Write the force in the cable as a vecto 12m- C 0.7 m 1.6 m.
A: The given problem can be solved by using the formulae FBC/|FBC| = rBC/|rBC| where FBCis the force…
Q: 5. F = x²i+ czj- yk If the force is conservative, the value of the constant c is O A OB O C O D OE…
A: To find: The value of constant c. Given: The force is F=x2i+czj-yk. The force is conservative.…
Q: C-6kN.m 0.2m 145 JAN -2m-
A:
Q: 5 Q5:The magnitude of the resultant ; (R ) of the force system shown in fig. -: below is equal to 3…
A:
Q: he region of safety in maximum shear stress theory contains which of the given shape *
A: The region of safety in maximum shear stress theory contains Hexagon.
Q: The magnitude of the moment produced by force F about segment AB of the pipe assembly is equal to…
A:
Q: 2. In the figure, D =0.5 ft; losses AB = 1.2 (v²/2g); losses BC = 0.8 (v²/2g). Determine the…
A: Given data: - The diameter of the pipe is D = 0.5 ft. The head loss between AB is hAB = 1.2v2/g.…
Q: F= (8i+ 6j + 8K)kN M= (-20î – 70j + 20k)kN-m 5m 3m 3m 6m 6m 4m 5m 7. Replace the forces with an…
A:
Q: Use the graphical method to construct the shear-force diagram and identify the magnitude of the…
A:
Q: the effect of force F2 on point P is F2 F3 F1 2 m 1 m O a. average normal stress and bending stress…
A:
Q: termine the the Reaction Force in the Vertical Direction at A
A: A is hinge joint so it will produce a vertical reaction. B is roller joint so it wont be able to…
Q: 2 m 3 m B 30° 1 m -0.75 m 60° The system shown is supported by journal bearings at points A, B, and…
A:
Q: • F1 = 10 N@ 120° • F2 = 75 N@ -90 then, what is the direction of the resultant force on the…
A:
Q: Which of the following is corresponds to the force acting at member AC? E 20 k 12 ft C D 12 ft 5 k B…
A: The free body diagram of the beam is as follow:
Q: The force F acting on the boom ABC at C points in the direction of the unit vector 0.5i - 0.4j +…
A:
Q: -240 mm C D 225 mm 1 225 mm 60 mm K 60 mm 135 mm 400 N
A:
Q: 4. For the Conduit shown, find the pressure head (P₂/y) at point (2). Knowing that: Q=25 L/s y =…
A: Pressure head at 1, P1γ=1.5 mElevation difference between 1 and 2, z1-z2=1.2 mFlow rate, Q=25…
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 3 images
- The A-36 steel pipe is subjected to the axial loading of 60 kN. Determine the change in volume of the material after the load is applied.How many 10-mm diameter rivets is needed to fasten member BF to the gusset plate at B if the member BF has thickness of 8 mm and the working stresses are 30 MPa for shear in the rivets and 45 MPa for bearing due to the rivets.The pressure relieve valve has a spool of 1.5 sq inches area, if a pressure of 150 psi is required to compress the sprint 0.25 inches to open the outlet port and reduce pressure(P) in the system. Evaluate the spring stiffness(k). F repestents spring force
- Perform the operation g(t)=2t+5f(t)= 2t+5find: (g+f)(t)The driver of the sports car applies his rear brakes and causes the tires to slip. If the normal force on each rear tire is 1800lb and the coefficient of kinetic friction between the tires and the pavement is { { \mu }_{ k }=0.5 }μk=0.5, determine the average shear stress developed by the friction force on the tires. Assume the rubber of the tires is flexible and each tire is filled with an air pressure of 225 kp.Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
- Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each having a radius of 45 mm. The cylinder is shown in the figure below. If the cylinder has a wall thickness of 2 Mm, determine the circumferential stress in the wall of the cylinder. Express your answer to three significant figures and include appropriate units.stress show complete solution and provide the -given -required -FBD -formula and solution4qwqwV4
- Determine the:1- Shear Strain2- Shear stress3- Friction CoefficientThe driver of the sports car applies his rear brakes and causes the tires to slip. If the normal force on each rear tire is 1800 N and the coefficient of kinetic friction between the tires and the pavement is { { \mu }_{ k }=0.5 }μk=0.5, determine the average shear stress developed by the friction force on the tires. Assume the rubber of the tires is flexible and each tire is filled with an air pressure of 225 K PThe 6-hp reducer motor can turn at 1200 rev>min. If the shaft has a diameter of 5 8 in., determine the maximum shear stress in the shaft.