Hydraulic drive is considered heavy duty and provide a smooth and strong movement within themachine tool design. Analyze the diagram of figure 1 below and answer the questions.OperativeelementHydraultccylinderRockingleverDirection-control vatve-ThrottlePressurevalve- Gear pumpFigure 1: Translatory Hydraulic Drivea) From your analysis, which of the component that is controlling the pressure delivered to thehydraulic cylinder?b) By the analysis of figure 1 above, compare the speed of the extend and retract of the hydrauliccylinder above.c) Define the function of the rocker arm in the figure.

From the analysis of the above figure

Hydraulic drive is considered heavy duty and provide a smooth and strong movement within the machine tool design. Analyze the diagram of figure 1 below and answer the questions. Operative element Hydraulfc cylinder Rocking lever Direction- control vatve -Throttle Pressure valve -Gear pump E Figure 1: Translatory Hydraulic Drive a) From your analysis, which of the component that is controlling the pressure delivered to the hydraulic cylinder? b) By the analysis of figure 1 above, compare the speed of the extend and retract of the hydraulic cylinder above. c) Define the function of the rocker arm in the figure.

Hydraulic drive is considered heavy duty and provide a smooth and strong movement within the machine tool design. Analyze the diagram of figure 1 below and answer the questions. Operative element Hydraulfc cylinder Rocking lever Direction- control vatve -Throttle Pressure valve -Gear pump E Figure 1: Translatory Hydraulic Drive a) From your analysis, which of the component that is controlling the pressure delivered to the hydraulic cylinder? b) By the analysis of figure 1 above, compare the speed of the extend and retract of the hydraulic cylinder above. c) Define the function of the rocker arm in the figure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q 2. (a) Why mechanical actuators are used in mechatronic system? What is the use of cams and followers in any system, compare the various cams in detail?(b) Give one example of a ratchet & pawl in design of any mechanical system? Give insight regarding application areas of hydraulic and pneumatic actuators?
Need help with this Dynamic problemwith a FBD .
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
What is the importance of time ratio? And explain the performance of four bar chain mechanismand conditions with neat diagram used in pump jacks in oil and field industries
pleassssse solve question 8, statics
20. A regenerative braking system stores kinetic energy of a car so that it can be recovered when the vehicle resumes moving. One way to do this is to “store” the energy in a spinning flywheel. One such design uses a solid disk flywheel with moment of inertia 0.040 kg m2 and maximum rotation rate 45000 rpm. (a) What is the maximum energy storage? (b) In principle it could store the kinetic energy of a 1700 kg car moving at what speed before braking? (c) If this energy is used to start the car moving again in 10.0 s, what is the power output of the system?
In a gear power transmission situation, the torque apppied on one gear is always created by: ____, no matter whay types of gears employed. Normal Force Tangential Force Radial Force Axial Force
The crank radius of a single-cylinder IC engine is 60 mm and the diameter of the cylinder is 80 mm. What is the swept volume of the cylinder?
What is the function of data acquisition system in mechatronic system? Explain the evolution of human machine interface? Why rack and pinion mechanism is used in industrial aspects, explain its principle with a possible sketch (a) Why mechanical actuators are used in mechatronic system? What is the use of cams and followers in any system, compare the various cams in detail? (b) Give one example of a ratchet & pawl in design of any mechanical system? Give insight regarding application areas of hydraulic and pneumatic actuators?
HWAC ENGG533
SUBJECT :DJJ40153 PNEUMATIC & HYDRAULIC POLITEKNIK MALAYSIA COURSE:DIPLOMA IN MECHANICAL ENGINEERING Draw the electro hydraulic circuit to controlled two double-acting cylinders and two hydraulic motors fixed displacement and the cylinder is electrically controlled with a single solenoid 4/2 valve THANK YOU SO MUCH
What is the main difference between a crankshaft and a cam shaft