i need clear ans by hand and solve very very fast in 20 min and thank you | Consider the system shown in figure (1). Design a compensator network Ge(s) that the static velocity error constant is 20 sec-¹ Verify the results of your design. R(s) Input Ge(s) Figure (1) 16 s(5+4) Y(s) output

i need clear ans by hand and solve very very fast in 20 min and thank you | Consider the system shown in figure (1). Design a compensator network Ge(s) that the static velocity error constant is 20 sec-¹ Verify the results of your design. R(s) Input Ge(s) Figure (1) 16 s(5+4) Y(s) output

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ex. 449. K*G(s)=K*1/(s(s+3)(s+6)) is the FTF of a unity-feedback closed-loop system. Calculate the asymptote centroid and show it on a professional root locus plot. Draw the asymptote plot separately. Determine the break-away point and K at the break-away point and show both on the plots. Formal documentation required. ans: 3
The previous solutions are posted on screenshot. please refer to them for gain value. solve : An integrator is added to the PD controller, leading to a PID controller C(s) = kp +ki/s + kds. Keep the PD controllers gains kp and kd from above, and plot the closed-loop poles as the gain ki varies from 0 ! 1 (Hint: The closed-loop poles satisfy 1 + P (s)C(s) = 0, translate this to Evan’s form 1 + kiG(s) = 0). Determine gains such that a load disturbance is rejected in about 10 time units, while keeping the amount of overshoot (from r to y) under 20%. Why can ki not be too large?
Assume any finite duration discrete time signal x(n) following the necessary condition satisfying the property of energy signal of your own choice. Now consider a discrete time system whichperforms Amplitude scaling operation followed by time reversal operation based on y(n) = ax(n) + x(-n). Sketch the output of resultant signal. Now classify and justify your answer with necessary and sufficient conditions that whether the above system based on all types of system.
a) What is the currenr flowing in the input resistor (i1) for t>0? b) What is the value of the feedback resistor Rf? c) What is the capacitor voltage in steady state (Vc( ∞ ))?
Exercise 10: Schmitt TriggerWe have the following Schmitt trigger, and our amp is powered by a+ -10V symmetrical source1 What type of Schmitt trigger is it? Calculate V'h, V'I and Vref2 Plot the hysteresis of this system
Consider ab N-bit DAC whose output varies from 0 to VFS (where the subscript FS denotes "full scale"). (a) Show that a change in the least significant bit (LSB) induces a change of VFS/(2N-1) in the output.This is the resolution of the converter. (b) Convince yourself that the DAC can produce any desired output voltage between 0 and VFS with at most VFS/2(2N-1) error (i.e., one-half the resolution). This is called quantization error of the converter. (c) For VFS = 5 V, how many bits are required tp obtain a resolution of 2 mV or better? What is the actual resolution obtained? What is the resulting quantization error?
For an op-amp having a slew rate SR = 8 V/ms, what is the maximum closed-loop voltage gain that can be used when the input signal varies by 0.5 V in 10 ms? Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below.
Figure 1 shows the equivalent circuit of a voltage amplifier with a source and aload connected to its input and output, respectively. Suppose that the sourceinternal resistance is Rs = 5 kΩ, the amplifier input resistance is RIN = 95 kΩ, theamplifier gain is A = 100, the amplifier output resistance is ROUT = 150 Ω and theload resistance is RL = 5 kΩ. For a sinusoidal input with amplitude VS = 5 mV, whatis the amplitude of the voltage VL across the load resistor RL? What would thevoltage across the load be without the amplifier?
For the op-amp circuit as shown below, given that RS = 46 kΩ, RL = 15 kΩ, R1 = 15 kΩ, R2 = 11 kΩ, R3 = 6.5 kΩ, R4 = 2.5 kΩ, R5 = 3 kΩ.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: FEEDBACK OSCILLATORS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:An amplifier without feedback has an internal gain of -500 with a distortion of 10% and a normal input of 0.5-volt, negative feedback with β = 0.10 was added. Determine the following:A. Gain of amplifier when the feedback was addedB. Percent reduction in distortion when feedback was addedC. The voltage required in the input of the amplifier in order that output voltage is the same as the voltage without feedback
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: FEEDBACK OSCILLATORS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:An amplifier without feedback has an internal gain of -500 with a distortion of 10% and a normal input of 0.5-volt, negative feedback with β = 0.10 was added. Determine the voltage required in the input of the amplifier in order that output voltage is the same as the voltage without feedback
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: FEEDBACK OSCILLATORS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:An amplifier without feedback has an internal gain of -500 with a distortion of 10% and a normal input of 0.5-volt, negative feedback with β = 0.10 was added. Determine the percent reduction in distortion when feedback was added