I Review A solar water heater mounted on the roof consists of two flat plates. Water enters at A and exits at B. Assume the average temperature of the water is 45°C. (Figure 1) Part A If the gap between the plates is a = 1.34 mm determine the maximum allowable pressure drop from A to B so that the flow remains laminar. Express your answer to three significant figures and include the appropriate units. HẢ ? Apmax = |2.37 kPa Figure < 1 of 1 > Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining 2 m Provide Feedback Next >

I Review A solar water heater mounted on the roof consists of two flat plates. Water enters at A and exits at B. Assume the average temperature of the water is 45°C. (Figure 1) Part A If the gap between the plates is a = 1.34 mm determine the maximum allowable pressure drop from A to B so that the flow remains laminar. Express your answer to three significant figures and include the appropriate units. HẢ ? Apmax = |2.37 kPa Figure < 1 of 1 > Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining 2 m Provide Feedback Next >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. What is the likelihood that a flow with an average velocity of 0.15 f t/s in a 6 in. water pipe is laminar? Find the speed at which the flow will always be laminar. 2. If the critical Reynolds number for a river is 2000 based on average velocity and depth, what is the maximum speed for laminar flow in a river 10 f t deep? 2 f t deep? Do you expect any river flow to be laminar?.
As shown in figure below, oil can be siphoned from a tank using a flexible hose, provided that the end of the hose at Point B, is below the free surface in the tank at Point A. The maximum elevation of the hose is at Point C. Oil is being siphoned from the tank through a constant-diameter hose. The end of the siphon at Point B is 6.71 meters below the oil top surface level of the tank at Point A. If the gauge pressure at Point C is 90.257 KPa and the density of oil is 890 fraction numerator k g over denominator m cubed end fraction , the vertical distance between Point C and Point B in meters is
13000000 ft3/day of CO must be delievered to aucstomer 60 miles away. The minimum pressure required at the customer's site is 300 psig. The pipe has a diameter of 10 in. Determine the source pressure required. Long pipelines may be considered isothermal at ground temperature at 60 oF. Standard conditions: T = 70 oF, P = 1 atm.
Air at a temperature of 40∘C∘C flows through the duct at A� with a velocity of 1.9 m/sm/s . ρair�air = 1.127 kg/m3kg/m3 Determine the change in pressure between A� and B�. Account for the minor loss caused by the sudden change in diameter of the duct. Express your answer to three significant figures and include the appropriate units.
Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1 and 2 are found to be 20 psi and 25 psi, respectively. The elevation of point 1 is 12 feet, and the elevation of point 2 is 0 feet. There is 15 feet of pipe between the two points. a. Determine the direction of flow. b. What is the minimum discharge above which the flow will not be laminar?
The figure shows a siphon that is used to draw waterfrom a large open tank. If the absolute vapor-pressureof the water is pv = 1.23 kPa. (a) determine the shortest drop length L of the50-mm-diameter tube that will cause cavitation in thetube. Show all your calculations. (b) Also draw the energy and hydraulic grade lines forthe length of the tube. Be sure to indicate the pressureheads, elevation heads, and dynamic heads. And toshow all your calculations.
A venturi meter is used to measure the flow rate of water at 55 degrees Celsius. The venturi meter has a throat diameter of 75mm, and it is situated in a 250-mm pipeline. A mercury (SG = 13.6) manometer measures the pressure difference, and the reading is 24 mm. Determine a.) the Reynolds number of the flow, b.) the average velocity, c) the volumetric flow rate, and d.) the power loss if 12% of the pressure drop is permanently lost.
1) 2) Determine the Reynolds number in the pipe system and the significance of this Information? 3) Using Bernoulli’s equation, find the water pressure at point C? 4) Determine the head losses accumulated by the fluid when flowing in the pipeline? 5) Calculate the energy that the fluid will lose after passing through the turbine by applying theenergy equation? 6)If the used turbine converts only two-thirds of the energy that the fluid will lose after passing through the turbine, what is the efficiency of this turbine? 7) Identify the most common water turbines and the limitations that exist within these differenttypes? 8) Although hydraulic turbines considered one of the most efficient power plants, theirecological impact is a big concern. Discuss this issue and suggest remedies for such problems by writing 100 words at least?
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 35m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = ..... b. Energy Loss along the straight pipe = ..... J / kg. c. Energy Loss at curves = ..... J / kg. d. Total energy to overcome friction = ..... J / kg. e. Energy to raise water according to height = ..... J / kg. f. The theoretical energy requirement for the pump is kg ethanol / second = ..... J / kg. g. Actual pump power requirement = ..... watts.
A water pump is used to pump the water to a large water tank as shown in Figure. The free surfaces of both water tanks are under atmospheric pressure. Dimensions and local losses are given below. The flow rate of the pump is determined as 16.2 L/min. Calculate the required manometric head of the pump and the required motor power if the total efficiency is 76.2 percent. The water at 10oC. density r = 996.2 kg/m3, dynamic viscosity µ = 1.362x10-3kg /ms. z2-z1 = 7.62 m (height difference), D = 2.62 cm (pipe diameter), L = 176.2 m (total pipe length), ɛ = 0.2562 mm (pipe roughness value) Local loss coefficients: KL,inlet = 0.562 (pipe inlet) KL,valve = 16.2 (valve), KL,elbow = 0.9262 (there are 5 elbows totally in pipe line), KL,outlet = 1.0562 (pipe outlet).
Determine the internal pressure of a liquid pipeline having an outside diameter of 8.625 in, a wall thickness of 0.5 in, and a yield strength of 32000 psi.
A rigid pipe has a diameter of 150 mm and a length of 1020 m. Water having bilk modulus of 2.0164 x109 Pa flows in the pipe. Calculate the velocity of sound in the water.