Part B Taking in your consideration the head losses accumulated by the fluid when flowing in the pipeline: 'Now determine water velocity at the pipeline exit as a function of time. Note that friction factor f can be calculated by using Blasius formula ( f = (100 * Re)0.25 ) if Reynolds number is less than 105

Part B Taking in your consideration the head losses accumulated by the fluid when flowing in the pipeline: 'Now determine water velocity at the pipeline exit as a function of time. Note that friction factor f can be calculated by using Blasius formula ( f = (100 * Re)0.25 ) if Reynolds number is less than 105

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 8 Two reservoirs are connected by a pipe whose total length is 360m.From the upper reservoir the pipe is 300mm in diameterfor a length of 150m and the remaining 210m is 450mm in diameter.The difference in water levels between the two reservoirs are 8m.Take f=0.006 for the smaller pipe and f=0.005 for the larger pipe.If all the changes in pipe sections are sharp and sudden, calculate the flow rate which can be delivered.
An air-conditioning system is designed to have a ductwith a rectangular cross section 1 ft by 2 ft, as shown. Duringconstruction, a truck driver backed into the duct and made it atrapezoidal section, as shown. The contractor, behind schedule,installed it anyway. For the same pressure drop along the pipe,what will be the ratio of the velocity in the trapezoidal duct tothat in the rectangular duct? Assume the Darcy-Weisbach resistance coefficient is the same for both ducts.
A fountain and a water tank will be powered by water from a nearby lake. The elevations and pipe connections are depicted in the diagram below. The fountain's jet water should reach a height of at least 2.5 m from the nozzle outlet. The tank, on the other hand, is elevated to allow gravity to distribute water. The table below contains the specifications for nozzles, suction and discharge pipes. What is the minimum power input to the pump in kW, assuming negligible minor head losses? Assume that the pump efficiency is 88 percent and the motor efficiency is 95 percent. The fountain's water is returned to the lake via a drainage system.
Water is pumped through a vertical 2-in. new galvanized-iron pipe to an elevated tank on the roof of a building. The pressure on the discharge side of the pump is 200 lb per sq in. What pressure can be expected at a point in the pipe 250 ft above the pump when the flow is 150 gpm? Answer should be: 37 lb per sq. inch Show your handwritten solution, thank you.
During the daytime, water is drawn from an upper reservoir and is run through a turbine on its way to a lower reservoir in order to produce power. The pipe is 300 feet long and has a 2.0-foot diameter. It is constructed of commercial steel which has a roughness height of = 0:0018 in. Find the power extracted by the turbine if the downward volume áow rate is 20,000 gallons per minute.(Recall that H2O = 1:94 slugs/ft3, H2O = 2:4 10^-5 slugs/fts.) You may assume that the turbine is 100% efficient.(b) Find the maximum power the turbine can deliver. What is the volume flow rate (in gallons per minute) for maximum power output? (Hint: plot power vs. flow rate in order to answer this question.)
What is the horsepower requirement for a water pump, if the required flow rate is 200 gpm and the required pressure increase assigned to the pump is 32 psi?
water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir height=220ft length of pipe= 1500ft final aubdivisiion= 24ft, 20psi 1)determine the normal pipe size 2) if the pipe size is not avalible what size combination will work 3) if we used a 8 inch pipe determine the min thickness 4)determine the max pressure that can deelope in the 8in system
Water at 60°F is pumped from a reservoir to the top of a mountain through a 6-in. Schedule 120 pipe at an average velocity of 12 ft/s. The pipe discharges into the atmosphere at a level 3,000 ft above the level in the reservoir. The pipeline itself is 4,500 ft long. If the overall efficiency of the pump and the motor driving it is 70 percent and the cost of electric energy to the motor is 4 cents per kilowatt hour, what is the hourly energy cost for pumping this water?
Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K copper tube if the volume flow rate of water at 60'F is Q 0.5 gal/min. Use increments of 0.05 in and include the velocity at the centerline. please be through and provide all calculus and graphs/tables
A reservoir has a depth of 20 ft. A pipe at the base of the reservoir needs to convey discharge of 2 cfs at 60°F. Find the diameter of the pipe. Assume no losses due to friction
10.) A horizontal pipe gradually reduces from 300 mm diameter section to 100 mm diameter section. The pressure at the 300 mm section is 100 kPa and at the 100 mm section is 70 kPa. If the flow rate is 15 liters/sec of water, compute the head lost between the two sections. Answer: 2.872m Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
A pump draws 24 li/s of water from the lower reservoir and lifts it to upper reservoir. The head lossfrom the inlet 150 mm pipe diameter is three times the velocity head and the head loss going to theoutlet 100mm pipe diameter is 25 times its velocity head. What is the power generated by the pump tothe system in horsepower. (Note: Velocities from the reservoir are different from the velocities of thepipe and pleaseee draw a diagram if you can thank you so much)